In this paper, the object of study is secure transmission and green energy transfer in full-duplex (FD) wireless-powered relay (WPR) secure systems, where an FD relay collects the power from radio-frequency signs and transmits the information in the face of multiple eavesdroppers. In order to improve the efficiency and safety of the contemporaneous wireless energy and information delivery, we propose a joint energy-signal- (ES-) aided secure beamforming and time-switch scheme under the self-power circulation protocol at the relay. The question formulated in this paper is to maximize the confidentiality rate according to energy restrictions at both the relay and energy receiver. As the question is non-salient and hard to resolve directly, we transform it into two sub-problems. For the first sub-problem, a two-level optimization technique is suggested to separately gain the optimal beamforming as well as the ES covariance. The extrinsic rank is a single-variable majorization question, wh... [more]

Organic Rankine cycle (ORC) is considered a promising heat-to-power technology to utilize waste heat and renewable energy, including solar, biomass and geothermal. However, since the thermodynamic, economic and environmental performance is usually conflict, the single objective design could no longer meet the requirements of the ORC system, putting forward urgent requirements for multi-objective optimization, which has attracted increasing attention with lots of papers published. However, due to these different decision variables, optimization objectives and approaches, existing research is significantly different from each other and is difficult to compare without a systematic summary. Therefore, this paper provides an overview of ORC multi-objective research from three perspectives: optimization objective, method and optimization parameters. Based on the classification of different objectives, this work summarizes the involved variables and provides a recommendation for selecting app... [more]

A deeply buried pipe energy pile (DBP-EP) combines the advantages of a ground source heat pump (GSHP) and an inside buried pipe energy pile (IBP-EP) and is an efficient, clean, and energy-saving technology. Based on field tests and numerical simulations, this paper explores the temperature distribution and heat exchange effects of DBP-EP under different influencing factors. The results show that when the pile-to-well ratio is approximately 0.3−0.4, the heat exchange of the energy pile obtains the best benefit; the inlet water temperature is the most significant factor affecting the heat exchange effect of the energy pile, and when combined with a reasonable pile-to-well ratio, the energy pile obtains the best heat exchange effect; the flow rate has a significant impact on the heat exchange effect of the energy pile, but needs to be set reasonably according to the pile-to-well ratio; the influence of inlet water temperature, well depth, flow rate, and pile length on the heat exchange ef... [more]

Transportation agencies optimize signals to improve safety, mobility, and the environment. One commonly used objective function to optimize signals is the Performance Index (PI), a linear combination of delays and stops that can be balanced to minimize fuel consumption (FC). The critical component of the PI is the stop penalty “K”, which expresses an FC stop equivalency estimated in seconds of pure delay. This study applies vehicular trajectory and FC data collected in the field, for a large fleet of modern vehicles, to compute the K-factor. The tested vehicles were classified into seven homogenous groups by using the k-prototype algorithm. Furthermore, multigene genetic programming (MGGP) is utilized to develop prediction models for the K-factor. The proposed K-factor models are expressed as functions of various parameters that impact its value, including vehicle type, cruising speed, road gradient, driving behavior, idling FC, and the deceleration duration. A parametric analysis is c... [more]

Propylene glycol monomethyl ether acetate (PGMEA) is a commonly used solvent in the rapidly developing semiconductor industry. Ultra-high purity PGMEA is required for this ultra-precision industry and to satisfy the current strict waste management regulations. The traditional PGMEA production process consumes considerable energy and has a high production cost. In this study, a novel heat integrated and intensified design, which applies a dividing wall column, reactive distillation, and pressure swing techniques, was proposed for improving the energy efficiency and reducing the cost of PGMEA production. Heat integration was applied to maximize the heat recovery of the process. All processes were simulated using the commercial simulator Aspen Plus V11. The economic and environmental parameters of the process alternative were assessed for a fair comparison with the conventional process. The results showed that heat integration of the optimal pressure swing-based reactive distillation and... [more]

Nowadays, robust and efficient solid waste collection is crucial to motivate citizens to participate in the circular economy by sorting recyclable solid waste. Vocational vehicles, including garbage trucks, contribute significantly to CO2 emissions; therefore, it is strongly recommended, and in the European Union it is mandatory, to replace conventional-fuel-based garbage trucks with electric ones. For providing sustainable and energy-efficient solid waste collection with a heterogeneous fleet, in-depth mathematical computations are needed to support solving complex decision-making problems, including crew rostering and vehicle routing, because the distance and capacity of electric garbage trucks differ from conventional-fuel-based ones. However, the literature on solid waste collection using electric garbage trucks is still relatively scarce. The main contribution of this paper is developing an optimization problem for balancing travel distance assigned to each garbage truck of a hete... [more]

Co-torrefaction of microalgae and lignocellulosic biomass was evaluated as a method to process microalgae sludge produced from various effluents and to obtain biochars with suitable properties for energy or material valorization. The influence of four independent variables on biochar yield and properties was evaluated by a set of experiments defined by response surface methodology (RSM). The biochars were characterized for proximate and ultimate composition, HHV, and methylene blue adsorption capacity. HHV of the biochars was positively correlated with carbonization temperature, residence time, and lignocellulosic biomass content in the feed. Co-torrefaction conditions that led to a higher yield of biochar (76.5%) with good calorific value (17.4 MJ Kg−1) were 250 °C, 60 min of residence time, 5% feed moisture, and 50% lignocellulosic biomass. The energy efficiency of the process was higher for lower temperatures (92.6%) but decreased abruptly with the increase of the moisture content o... [more]

Owing to scale-up and complex wake effects, the centralized control that processes the command from turbines may be unsuitable, as it incurs high communication overhead and computational complexity for a large offshore wind farm (OWF). This paper proposes a novel decentralized non-convex optimization strategy for maxing power conversion of a large OWF based on a modified beetle antennae search (BAS) algorithm. First, an adaptive threshold algorithm which to establish a pruned wake direction graph while preserving the most critical wake propagation relationship among wind turbines are presented. The adaptive graph constraints were used to create wake sub-digraphs that split the wind farm into nearly uncoupled clustering communication subsets. On this basis, a Monte Carlo-based beetle annealing search (MC-BAS) nonlinear optimization strategy was secondly designed to adjust the yaw angles and axial factors for the maximum power conversion of each turbine subgroup. Finally, the simulation... [more]

The Rankine cycle is widely used for electricity production. Significant weight and size characteristics of the power equipment working on superheated steam are the main disadvantages of such power plants. The transition to supercritical carbon dioxide (S-CO2) working fluid is a promising way to achieve a significant reduction in equipment metal consumption and to increase energy efficiency. This paper presents the results of thermodynamic analysis of S-CO2 thermal power plants (TPPs) utilizing the heat of combustion products of an energy boiler. It was found that the net efficiency of the developed S-CO2 TPP with a pulverized coal-fired boiler reached 49.2% at an initial temperature of 780 °C, which was 2% higher compared to the efficiency level of steam turbine power plants (STPPs) at a similar turbine inlet temperature.

This paper presents a comparison between two design methodologies applied to permanent magnet synchronous machines for hybrid and electric vehicles (HEVs and EVs). Both methodologies are based on 2D finite element models and coupled to a genetic algorithm to optimize complex non-linear geometries such as multi-layer permanent magnet machines. To reduce the computation duration to evaluate Induced Voltage and Iron Losses for a given electrical machine configuration, a new methodology based on geometrical symmetries and magnetic symmetries are used and is detailed. Two electromagnetic models have been developed and used in the design stage. The first model was the stepped rotor position finite element analysis called abc model which considered the spatial harmonics without any approximation of the waveform of flux linkage inside the stator, and the second model was based on a fixed rotor position called dq model, with the approximation that the waveform of flux linkage inside the stator... [more]

The use of hybrid renewable energy systems (HRES) has become the best option for supplying electricity to sites remote from the central power system because of its sustainability, environmental friendliness, and its low cost of energy compared to many conventional sources such as diesel generators. Due to the intermittent nature of renewable energy resources, there is a need however for an energy storage system (ESS) to store the surplus energy and feed the energy deficit. Most renewable sources used battery storage systems (BSS), a green hydrogen storage system (GHSS), and a diesel generator as a backup for these sources. Batteries are very expensive and have a very short lifetime, and GHSS have a very expensive initial cost and many security issues. In this paper, a system consisting of wind turbines and a photovoltaic (PV) array with a pumped hydro energy storage (PHES) system as the main energy storage to replace the expensive and short lifetime batteries is proposed. The proposed... [more]

Energy saving is an important issue for multiple-chiller systems. Optimal chiller loading (OCL) in multiple-chiller systems has been investigated with many optimization algorithms to save energy. Particle swarm optimization (PSO) algorithm has been successful in solving this problem in some cases, but not in all. This study innovatively added a team evolution to the original particle swarm optimization algorithm, called team particle swarm optimization (TPSO). The TPSO enhances the effectiveness of original particle swarm optimization to better solve the OCL problem. The TPSO algorithm is composed of two evolutions: particle evolution and team evolution. The partial load ratio (PLR) of each operating chiller and the on-off state of each chiller are the particle evolution parameters and team evolution parameters, respectively. To evaluate the performance of the proposed method, this paper adopts three case studies so the results generated from the proposed algorithm TPSO, the original p... [more]

Unmanned aerial vehicles (UAVs) have been widely used in military and civilian applications. However, the insufficient cruising range restricts the development of UAVs due to the limitation of their battery. Inductive power transfer (IPT) is an effective way to charge the battery and solve this problem. Magnetic coupler is a key component of the IPT system, which greatly affects the power transfer and efficiency of the IPT. This paper proposes a new magnetic coupler with vertical spiral coils and ferrite PQI cores for the IPT system of UAVs, which can enhance the magnetic coupling and improve the performance of the IPT system. Finite element simulations are used to investigate the magnetic field distribution and coupling capability of the proposed magnetic coupler. In addition, an experimental platform is built to prove the validity of the IPT system using the proposed magnetic coupler. The results show that the coupling coefficient can reach 0.98, and the system transfer efficiency is... [more]

Energy efficiency (EE) is of great concern in cognitive radio networks since the throughput and energy consumption of secondary users (SUs) vary with the sensing time. However, the conditions of the detection probability and false alarm probability should be respected to better protect primary users (PUs) and to improve the sensing performance of SUs. Additionally, the PUs’ minimum averaged power provision should also be regarded as a key problem of interactive linking to SUs. Therefore, an integrated design between the PU and SUs is desired for the coordination of the whole cognitive radio system, especially regarding the satisfaction of EE and performance metrics. This study formulates sensing constraints in a unified way and calculates the minimum SNR of SUs, based on which the essential PU power provision is computed. Furthermore, EE is proved as a decreasing function with the PU’s active ratio, where the maximum EE is obtained corresponding to the minimum QoS requirements of the s... [more]

The highest economic costs of a geothermal plant are basically related to well drilling and heat exchanger maintenance cost due to the chemical aggressiveness of geothermal fluid. The possibility to reduce these costs represents an opportunity to push toward geothermal plants development. Such challenges are even more important in the sites with a low-medium temperature geothermal fluids (90−120 °C) availability, where the use of these fluids for direct thermal uses can be very advantageous. For this reason, in this study, a direct geothermal heating system for a building will be investigated by considering a plastic plate heat exchanger. The choice of a polymeric heat exchanger for this application is upheld by its lower purchase cost and its higher fouling resistance than the common metal heat exchangers, overcoming the economic issues related to conventional geothermal plant. Thus, the plastic plate heat exchanger was, firstly, geometrical and thermodynamical modeled and, after, exe... [more]

Syngas fermentation via the Wood-Ljungdahl (WL) pathway is a promising approach for converting gaseous pollutants (CO and CO2) into high-value commodities. Because the WL involves several enzymes with trace metal components, it requires an adequate supply of micronutrients in the fermentation medium for targeted bioprocessing such as bioethanol production. Plackett-Burman statistical analysis was performed to examine the most efficient trace elements (Ni, Mg, Ca, Mn, Co, Cu, B, W, Zn, Fe, and Mo) and their concentrations for Clostridium ljungdahlii on ethanol production. Overall, 1.5 to 2.5 fold improvement in ethanol production could be achieved with designed trace element concentrations. The effects of tungsten and copper on ethanol and biomass production were determined to be the most significant, respectively. The model developed was statistically significant and has the potential to significantly decrease the cost of trace element solutions by 18−22%. This research demonstrates th... [more]

This paper aims to explore torque optimization control issue in the turning of EV (Electric Vehicles) with motorized wheels for reducing energy consumption in this process. A three-degree-of-freedom (3-DOF) vehicle dynamics model is used to analyze the total longitudinal force of the vehicle and explain the influence of torque vectoring distribution (TVD) on turning resistance. The Genetic Algorithm-Particle Swarm Optimization Hybrid Algorithm (GA-PSO) is used to optimize the torque distribution coefficient offline. Then, a torque optimization control strategy for obtaining minimum turning energy consumption online and a torque distribution coefficient (TDC) table in different cornering conditions are proposed, with the consideration of vehicle stability and possible maximum energy-saving contribution. Furthermore, given the operation points of the in-wheel motors, a more accurate TDC table is developed, which includes motor efficiency in the optimization process. Various simulation re... [more]

The circulating cooling water system is widely used in various industrial production fields, and its operating cost largely depends on external factors, such as ambient temperature and working medium flow. Considering the relative elevation of the heat exchanger, this study establishes a total system operation cost analysis and optimization model based on the superstructure method. The model uses ambient dry bulb temperature, ambient wet bulb temperature, and working medium flow as random variables. Water supply temperature is adopted as the decision variable, and the minimum operating cost of the system is used as the objective function. An analysis of the effect of the three random variables on the operation cost shows that the effect of ambient dry bulb temperature on the operation cost is negligible, and the effect of ambient wet bulb temperature and working medium flow on the operation cost is significant. In addition, a control equation of water supply temperature is established... [more]

In the process of gas prediction and early warning, outliers in the data series are often discarded. There is also a likelihood of missing key information in the analysis process. To this end, this paper proposes an early warning model of coal face gas multifactor coupling relationship analysis. The model contains the k-means algorithm based on initial cluster center optimization and an Apriori algorithm based on weight optimization. Optimizing the initial cluster center of all data is achieved using the cluster center of the preorder data subset, so as to optimize the k-means algorithm. The optimized algorithm is used to filter out the outliers in the collected data set to obtain the data set of outliers. Then, the Apriori algorithm is optimized so that it can identify more important information that appears less frequently in the events. It is also used to mine and analyze the association rules of abnormal values and obtain interesting association rule events among the gas outliers i... [more]

Solar Tracking Systems are useful to increase the generation efficiency of photovoltaic technology, mainly for concentration technology, where dual-axis is required on account of the high accurate alignment to the Sun. Even when there exists a strong relation between tracking error and energy efficiency, multiple technological and research developments have sought to solve these problems independently. The present research proposes a novel concurrent design methodology for optimizing the overall performance of two-axis trackers, allowing to keep a balance between the tracking error and the energy consumption from the design stage, from an optimization approach. The concurrent approach was implemented to design a Solar Tracker as a solar monitoring system, was compared with four commercial systems, obtaining a similar pointing accuracy with a mixed tracking error of 0.0942°. The system has the best energy balance, consuming only 0.9641% of the energy generated for the tracking action, b... [more]

We analyzed the potential of thermoelectrics for electricity generation in a combined heat and power (CHP) waste heat recovery system. The state-of-the-art organic Rankine cycle CHP system provides hot water and space heating while electricity is also generated with an efficiency of up to 12% at the MW scale. Thermoelectrics, in contrast, will serve smaller and distributed systems. Considering the limited heat flux from the waste heat source, we investigated a counterflow heat exchanger with an integrated thermoelectric module for maximum power, high efficiency, or low cost. Irreversible thermal resistances connected to the thermoelectric legs determine the energy conversion performance. The exit temperatures of fluids through the heat exchanger are important for the system efficiency to match the applications. Based on the analytic model for the thermoelectric integrated subsystem, the design for maximum power output with a given heat flux requires thermoelectric legs 40−70% longer th... [more]

This paper studies energy consumption management of seawater Reverse Osmosis (RO) desalination plants to maintain and enhance the Voltage Stability (VS) of Power Systems (PS) with Photovoltaic (PV) plant integration. We proposed a voltage-based management algorithm to determine the maximum power consumption for RO plants. The algorithm uses power flow study to determine the RO plant power consumption allowed within the voltage-permissible limits, considering the RO process constraints in order to maintain the desired fresh water supply. Three cases were studied for the proposed RO plant: typical operation with constant power consumption, controlled operation using ON/OFF scheduling of the High-Pressure Pumps (HPPs) and controlled operation using Variable Frequency Drive (VFD) control. A modified IEEE 30-bus system with a variable load was used as a case study with integration of three PV plants of 75 MWp total power capacity. The adopted 33.33 MW RO plant has a maximum capacity of 200,... [more]

Economic Dispatch (ED) problems have been solved using single-objective optimization for so long, as Grid System Operators (GSOs) previously only focused on minimizing the total production cost. In modern power systems, GSOs require not only optimizing the total production cost but also, at the same time, optimizing other important objectives, such as the total emissions of the greenhouse gasses, total system loss and voltage stability. This requires a suitable multi-objective optimization approach in ensuring the ED solution produced is satisfying all the objectives. This paper presents a new multi-objective optimization technique termed Multi-Objective Immune-Commensal-Evolutionary Programming (MOICEP) for minimizing the total production cost and total system loss via integrated Economic Dispatch and Distributed Generation installation (ED-DG). This involved the application of a weighted-sum multi-objective approach that combined with an optimization technique called Immune-Commensal... [more]

The analytical solutions of complex dynamic PRO systems pose challenges to ensuring that maximum power can be harvested in stable, rapid, and efficient ways in response to varying operational environments. In this paper, a boosted particle swarm optimization (BPSO) method with enhanced essential coefficients is proposed to enhance the exploration and exploitation stages in the optimization process. Moreover, several state-of-the-art techniques are utilized to evaluate the proposed BPSO of scaled-up PRO systems. The competitive results revealed that the proposed method improves power density by up to 88.9% in comparison with other algorithms, proving its ability to provide superior performance with complex and computationally intensive derivative problems. The analysis and comparison of the popular and recent metaheuristic methods in this study could provide a reference for the targeted selection method for different applications.

This paper presents research results on heat pipe numerical models as optimization of heat pipe heat exchangers for intensification of heat exchange processes and the creation of heat exchangers with high efficiency while reducing their dimensions. This work and results will allow for the extension of their application in passive and low-energy construction. New findings will provide a broader understanding of how heat pipes work and discover their potential to intensify heat transfer processes, heat recovery and the development of low-energy building engineering. The need to conduct research and analyses on the subject of this study is conditioned by the need to save primary energy in both construction engineering and industry. The need to save primary energy and reduce emissions of carbon dioxide and other pollutants has been imposed on the EU Member States through multiple directives and regulations. The presented numerical model of the heat pipe and the results of computer simulati... [more]