In smart grids, homes are equipped with smart meters (SMs) to monitor electricity consumption and report fine-grained readings to electric utility companies for billing and energy management. However, malicious consumers tamper with their SMs to report low readings to reduce their bills. This problem, known as electricity fraud, causes tremendous financial losses to electric utility companies worldwide and threatens the power grid’s stability. To detect electricity fraud, several methods have been proposed in the literature. Among the existing methods, the data-driven methods achieve state-of-art performance. Therefore, in this paper, we study the main existing data-driven electricity fraud detection methods, with emphasis on their pros and cons. We study supervised methods, including wide and deep neural networks and multi-data-source deep learning models, and unsupervised methods, including clustering. Then, we investigate how to preserve the consumers’ privacy, using encryption and... [more]

Electric vehicles (EVs) are spreading fast as they promise to provide better performance and comfort, but above all, to help face climate change. Despite their success, their cost is still a challenge. Lithium-ion batteries are one of the most expensive EV components, and have become the standard for energy storage in various applications. Precisely estimating the remaining useful life (RUL) of battery packs can encourage their reuse and thus help to reduce the cost of EVs and improve sustainability. A correct RUL estimation can be used to quantify the residual market value of the battery pack. The customer can then decide to sell the battery when it still has a value, i.e., before it exceeds the end of life of the target application, so it can still be reused in a second domain without compromising safety and reliability. This paper proposes and compares two deep learning approaches to estimate the RUL of Li-ion batteries: LSTM and autoencoders vs. CNN and autoencoders. The autoencode... [more]

OpenMOC-HEX, a neutron transport calculation code with hexagonal modular ray tracing, has the capability of domain decomposition parallelism based on an MPI parallel programming model. In this paper, the optimization of inter-node communication was studied. Starting from the specific geometric arrangement of hexagonal reactors and the communication features of the Method of Characteristics, the computation and communication of all the hexagonal assemblies are mapped to a graph structure. Then, the METIS library is used for graph partitioning to minimize the inter-node communication under the premise of load balance on each node. Numerical results of an example hexagonal core with 1968 energy groups and 1027 assemblies demonstrate that the communication time is reduced by about 90%, and the MPI parallel efficiency is increased from 82.0% to 91.5%.

The operation of a water supply system (WSS) is inextricably linked with the possibility of different types of failure. It is very common for these failures to be random in nature. The results of reliability studies carried out in many water supply systems revealed, for example, the possibility of incidental water pollution, power supply issues, failure in machinery, damage to water plants, or natural disasters. As a result of the WSS failure, we deal with a state of threat to safety (TSS) or a state of loss of safety (LSS). Using Markov processes, we developed a failure model of the WSS to determine the possibility that the system may find itself in different states of safety. As a result, a mathematical model using Markov processes has been proposed for each of these distinct states of safety (complete safety state—CSS; threat to safety state—TSS; and loss of safety state—LSS). The proposed approach in the water supply system will limit emergency states by optimizing working and repa... [more]

Hydrogen (H2) energy is an ideal non-polluting renewable energy and can achieve long-term energy storage, which can effectively regulate the intermittence and seasonal fluctuation of solar energy. Solid oxide fuel cells (SOFC) can generate electricity from H2 with only outputs of water, waste heat, and almost no pollution. To solve the power generation instability and discontinuity of solar photovoltaic (PV) systems, a hybrid PV-SOFC power generation system has become one feasible solution. The “digital twin”, which integrates physical systems and information technology, offers a new view to deal with the current problems encountered during smart energy development. In particular, an accurate and reliable system model is the basis for achieving this vision. As core components, the reliable modelling of the PV cells and fuel cells (FCs) is crucial to the whole hybrid PV-SOFC power generation system’s optimal and reliable operation, which is based on the reliable identification of unknow... [more]

To effectively improve the dust reduction rate of fine dust and prevent the occurrence of secondary dust, surfactant-charged water mist dust reduction technology is proposed. First, the water mist induction-charged atomization mechanism was perfected by an induction-charged spray experiment and the optimal atomization-charged voltage was determined to be 10 kV. Second, by surface tension and spray experiments on AEO-9-charged solutions, the lower the surface tension and viscosity of the solution, the better the atomization effect; the best atomization solution was 10 kV and 0.02% AEO-9. Finally, according to an electrostatic adsorption experiment, it was identified that there was an electrostatic interaction between coal dust and charged droplets. The contact angle experiment showed that the contact angle of the AEO-9 droplets decreased by 68.44% compared with water after 3 s of contact with coal dust. The wetting effect of bituminous coal was significantly improved by adding AEO-9 to... [more]

Thermal design and the choice of turbulence models are crucial for motors. In this project, the geometrical model of the vertical shielding induction motor for a small nuclear main pump was established by SolidWorks software and the finite volume method was adopted to investigate the temperature of the motor, especially the temperatures of bearings lubricated water. To make the numerical simulation of flow and heat transfer in the rotating clearance of the shielding induction motor more accurate, the effects of four types of different two equation turbulence models on the temperature field of the shielding induction motor were studied. The results showed that different choices of turbulence models had little effect on the temperature of the winding insulation but influenced the temperature of the lower guide bearing lubricating water and the secondary cooling water outlet. The SST k-ω model showed the lowest relative error result of the temperature of the winding insulation and the bea... [more]

To further the development of low-enriched uranium fuels, precedence has been placed on delivering the same amount of power while lowering the fuel temperature and radial temperature gradient. To address this, modeling efforts have resulted in a novel design featuring conductive fins of varying thermal conductivities and geometries inserted into the fuel matrix. These conductive inserts were not allowed to exceed 6% of the original fuel volume. This constraint was imposed due to other designs displacing 10% of fuel volume. A parametric study was performed that consisted of 2.56 million BISON simulations involving varying fin characteristics (i.e., fin thermal conductivity, number, and geometry) to determine the optimal geometric configuration for a desired amount of fuel volume displaced. The results from this study show that the thickness and length of each fin affect the fuel temperature and temperature gradient more than varying the number and thermal conductivity of the fins. The p... [more]

Studying a large number of scenarios is necessary to consider the uncertainty inherent to the energy transition. In addition, the integration of intermittent renewable energy sources requires complex energy system models. Typical days clustering is a commonly used technique to ensure the computational tractability of energy system optimisation models, while keeping an hourly time step. Its capability to accurately approximate the full-year time series with a reduced number of days has been demonstrated (i.e., a priori evaluation). However, its impact on the results of the energy system model (i.e., a posteriori evaluation) is rarely studied and was never studied on a multi-regional whole-energy system. To address this issue, the multi-regional whole-energy system optimisation model, EnergyScope Multi-Cells, is used to optimise the design and operation of multiple interconnected regions. It is applied to nine diverse cases with different numbers of typical days. A bottom-up a posteriori... [more]

To ensure the applicability of accident-tolerant fuels, their behaviors under various accidental conditions must be assessed. While the dependences of the behavior of single physical parameters can be investigated in single- or separate-effect experiments, and more complex phenomena can be investigated using integral-effect tests, the behavior of an entire system as complex as a nuclear power plant core must be investigated using computer code modeling. One of the most commonly used computer codes for the assessment of severe accidents is MELCOR 2.2. In version 18019, the authors enabled the modeling of the behavior of the nuclear fuel with FeCrAl cladding (namely, alloy B136Y3) for the first time, using the GOX model. The ability of this model to reasonably accurately predict the behavior of FeCrAl cladding in accident conditions with quenching was verified in this work by modeling the QUENCH-19 experiment carried out in the Karlsruhe Institute of Technology on the QUENCH experimental... [more]

One method to reduce CO2 emissions from vehicle exhaust is the use of liquified petroleum gas (LPG) fuel. The global use of this fuel is high in European countries such as Poland, Romania, and Italy. There are a small number of computational models for the purpose of estimating the emissions of LPG vehicles. This work is one of the first to present a methodology for developing microscale CO2 emission models for LPG vehicles. The developed model is based on data from road tests using the portable emission measurement system (PEMS) and on-board diagnostic (OBDII) interface. This model was created from a previous exploratory data analysis while using gradient-boosting machine learning methods. Vehicle velocity and engine RPM were chosen as the explanatory variables for CO2 prediction. The validation of the model indicates its good precision, while its use is possible for the analysis of continuous CO2 emissions and the creation of emission maps for environmental analyses in urban areas. T... [more]

In light of the rapidly growing number of photovoltaic micro-grids, the modelling of their short-term power yields based on meteorological measurements is increasing in significance. This requires the knowledge of total and diffuse instantaneous solar radiation; however, most meteorological stations conduct actinometric measurements only with regard to total solar radiation, especially on a minute scale. This paper contains an analysis of the currently used PV cell mathematical model and suggests its modification aimed at calculating PV cell power with satisfactory accuracy, without the knowledge of diffuse solar radiation. Three function families were proposed to approximate the relationship between diffuse irradiance and the total and theoretical total irradiance variance for a cloudless sky. A program has been implemented to identify functions from the aforementioned function families. It leverages an evolution strategy algorithm and a fitness function based on the least-squares poi... [more]

This paper proposes a component-oriented modeling method for power system simulation, which optimizes the modeling process of the FPGA-based real-time digital simulator (FRTDS) to enhance its computational efficiency. In this paper, a component modeling method for various types of elements in the power system is presented, which makes the modeling process in FRTDS more user-friendly and highly scalable. By applying the concepts of combination and reconstruction of components to electrical components, the component-oriented modeling method becomes better suited for combined elements with fixed connection modes and elements that require online model replacement in the power system. Utilizing the characteristics of component-oriented modeling, the variable declaration structure and node elimination strategy in the simulation script are optimized, enabling the simulation script to fit better with the hardware structure of FRTDS. Additionally, a substation is simulated in FRTDS with a simul... [more]

Compositional engineering is considered one of the recent interesting techniques used in the field of perovskite solar cells (PSCs). In this method, more than one material was used in a specific cation in the perovskite structure. This work aims to simulate the cesium-containing triple-cation perovskite (TCP) via the SCAPS-1D simulation program with a device structure of ITO/SnO2/TCP/Spiro-OMeTAD/Au. First, we studied the effect of interface defects on the PCSs with respect to experimental results and found that when no interface defects occur, the power conversion efficiency (PCE) reaches a value of 22.16% which is higher than the reported PCE, implying that the fabricated cell suffers from the interface defects as a main effect on cell degradation. Incorporating interface defects into the simulation results in a very good match between the experimental and simulated data with a PCE of 17.92%. Further, to provide possible routes to enhance the performance of the solar cell under inves... [more]

A suspended open-type ceiling radiant cooling panel (CRCP) has been proposed recently. The main challenge is improving its cooling performance to overcome limitations for extensive use. Therefore, this study aims to optimize the design of CRCPs with curved and segmented structure to enhance heat transfer. A three-dimensional CFD model was developed to investigate the cooling capacity and heat transfer coefficient of the CRCPs installed inside a single enclosed room. Panel structure was determined based on four dependent parameters: the panel curvature width (L, m), the panel curvature radius (r, m), the void distance (d, m) between each panel or panel segment, and the panel coverage area (Ac, m2). The panel surface area (As, m2) and the ratio of panel curvature width to radius (L/r) were also examined. A total of 35 designs were compared under 7 different cooling load conditions, and 245 cases were carried out. The results show that the nominal cooling capacity and heat transfer coeffi... [more]

Currently, 90% of Kazakhstan’s oil is situated in 15 oil and gas fields where simple cycle gas turbines are utilized for electricity generation. The need for developing techniques to enhance the efficiency and eco-friendliness of fuel consumption in Kazakhstan’s oil fields is imperative. In this article, methods for improving the energy efficiency of a simple gas turbine power plant functioning in an oil field are discussed, with consideration given to the impact of ambient temperature and specific environmental constraints, such as water scarcity and high temperatures. Two schemes to increase efficiency are evaluated: the first involves the utilization of a waste heat boiler for steam production intended for technological purposes, while the second involves electricity generation through a combination of a waste heat boiler and a steam turbine. Models based on Aspen HYSYS were formulated, with actual gas turbine power plant operation taken into account. Analysis indicated that a waste... [more]

Molten carbonate fuel cells (MCFCs) use molten carbonate as an electrolyte. MCFCs operate at high temperatures and have the advantage of using methane as a fuel because they can use nickel-based catalysts. We analyzed the performance of an internal manifold-type MCFC, according to operating conditions, using computational fluid dynamics. Different conditions were used for the external and internal reforming-type MCFCs. Flow directions, gas utilization, and operating temperatures were used as the conditions for the external reforming-type MCFCs. The S/C ratio and reforming area were used as the conditions for internal reforming-type MCFCs. A simulation model was developed, considering gas transfer, reforming reaction, and heat transfer. The simulation results of external reforming-type MCFCs showed similar pressure drops in all flow directions. As the gas utilization decreased, the temperature decreased, but the performance increased. The performance improved with increasing operating t... [more]

Asymmetric thermal zones or even non-rectangular structures are common in residential buildings. These types of structures are not easy to model with specialized programs, and it is difficult to know the heat flows and the relationships between the different variables. This paper presents a methodology for modeling structures with multiple thermal zones using the graph theory arrangement. The methodology allows for generating a mathematical model using all the walls of each thermal zone. The modeling method uses the lumped parameter technique with a structure of two resistors and two capacitors for each thermal zone. The walls and internal surfaces of each zone define the thermal resistances, and the elements for the network structure are created by reducing resistances. The structure selected as a case study is similar to a residential apartment, which demonstrates the possibility of modeling complex and non-traditional structures. The accuracy of the generated mathematical model is v... [more]

The 5th generation (5G) cellular networks offer high speeds, low latency, and greater capacity, but they face greater penetration loss through buildings than 4G due to their higher frequency bands. To reduce this loss in energy-efficient buildings, a passive antenna system was developed and integrated into sandwich walls. However, the thermal effects of this system, which includes highly thermally conductive metals, require further study. In this research, three-dimensional heat transfer simulations were performed using COMSOL Multiphysics to determine the thermal transmittances (U-values) of 5G antenna walls. The results revealed that, using stainless steel as the connector material (current design), the U-value rose from 0.1496 (for the wall without antenna) to 0.156 W/m2K, leading to an additional heating loss per year of only 0.545 KWh/m2 in Helsinki. In contrast, with the previous design that used copper as the connector material, the U-value increased dramatically to 0.3 W/m2K, e... [more]

Adiabatic Compressed Air Energy Storage (ACAES) is regarded as a promising, grid scale, medium-to-long duration energy storage technology. In ACAES, the air storage may be isochoric (constant volume) or isobaric (constant pressure). Isochoric storage, wherein the internal pressure cycles between an upper and lower limit as the system charges and discharges is mechanically simpler, however, it leads to undesirable thermodynamic consequences which are detrimental to the ACAES overall performance. Isobaric storage can be a valuable alternative: the storage volume varies to offset the pressure and temperature changes that would otherwise occur as air mass enters or leaves the high-pressure storage. In this paper we develop a thermodynamic model based on expected ACAES and existing CAES system features to compare the effects of isochoric and isobaric storage. Importantly, off-design compressor performance due to the sliding storage pressure is included by using a second degree polynomial fi... [more]

Digital reflections of physical energy plants can help support and optimize energy technologies within their lifecycle. So far, no framework for the evolution of virtual representations throughout the process development lifecycle exists. Based on various concepts of virtual representations in different industries, this review paper focuses on developing a novel virtual representation framework for the process development environment within the energy sector. The proposed methodology enables the continuous evolution of virtual representations along the process development lifecycle. A novel definition for virtual representations in the process development environment is developed. Additionally, the most important virtual representation challenges, properties, and applications for developing a widely applicable framework are summarized. The essential sustainability indicators for the energy sector are listed to standardize the process evaluation throughout the process development lifecy... [more]

This paper presents a numerical model of a four-pass supercritical steam superheater with a complex flow system. The specific heat of steam is a function of temperature and pressure, and the specific heat of flue gas is a function of temperature. Pressure and temperature changes along the length of the tubes were also determined. The modified Churchill equation was used to calculate the steam-side friction factor of Darcy−Weisbach. The flue gas temperature variations behind the individual superheater tube rows were calculated. The steam and wall temperature distributions were determined in each tube row along its length. Knowing the temperature of the tube walls and the steam along the flow direction enables the selection of the correct steel grade for the tubes. Thanks to this advantage of the proposed method, the investment can be reduced in superheater construction without the danger of overheating the tube material. The results of the superheater simulation were compared with the r... [more]

A unique rotary kite turbine designed with tensile rotary power transmission (TRPT) is introduced in this work. Power extraction, power transmission and the ground station are modelled in a modular framework. The TRPT system is the key component of power transmission, for which three models with different levels of complexity are proposed. The first representation is based on the stationary state of the system, in which the external and internal torques of a TRPT section are in equilibrium, referred to as the steady-state TRPT model. The second representation is a simplified spring-disc model for dynamic TRPT, and the third one is a multi-spring model with higher degrees of freedom and more flexibility in describing TRPT dynamics. To assess the torque loss on TRPT, a simple tether drag model is written for the steady-state TRPT, followed by an improved tether drag model for the dynamic TRPT. This modular framework allows for multiple versions of the rotor, tether aerodynamics and TRPT... [more]

Similar to parafoils, ram-air kites are flexible membrane wings inflated by the apparent wind and supported by a bridle line system. A major challenge in estimating the performance of these wings using a computer model is the strong coupling between the airflow around the wing and the deformation of the membrane structure. In this paper, we introduce a staggered coupling scheme combining a structural finite element solver using a dynamic relaxation technique with a potential flow solver. The developed method proved numerically stable for determining the equilibrium shape of the wing under aerodynamic load and is thus suitable for performance measurement and load estimation. The method was validated with flight data provided by SkySails Power. Measured forces on the tether and steering belt of the robotic kite control pod showed good resemblance with the simulation results. As expected for a potential flow solver, the kite’s glide ratio was overestimated by 10−15%, and the measured teth... [more]

In this study, thermodynamic modeling and simulations were used to optimize the design point performance of the Allam cycle. The topic fits perfectly with the strategies for power sector decarbonization toward net zero emission. In fact, it offers an environmentally friendlier alternative to natural gas combined cycle (NGCC) plants. The focus is on oxyfuel combustion that, combined with supercritical CO2 (sCO2) stream as working fluid, produces high-purity CO2, electricity, and water by means of a highly recuperated Brayton cycle. The former is ready for sequestration, pipeline injection, or other applications, such as enhanced oil recovery or industrial processes. Being designed within the last decade, large-scale plants are poorly documented in the published literature and not yet ready for operation. Accordingly, a thermodynamic model was developed for a net power (Pn) output of 300 MW. After validation against the little data available from academic studies, simulation sets were co... [more]