Globally, buildings account for nearly 40% of the total primary energy consumption and are responsible for 20% of the total greenhouse gas emissions. Energy consumption in buildings is increasing with the increasing world population and improving standards of living. Current global warming conditions will inevitably impact building energy consumption. To address this issue, this report conducted a comprehensive study of the impact of climate change on residential building energy consumption. Using the methodology of morphing, the weather files were constructed based on the typical meteorological year (TMY) data and predicted data generated from eight typical global climate models (GCMs) for three representative concentration pathways (RCP2.6, RCP4.5, and RCP8.5) from 2020 to 2100. It was found that the most severe situation would occur in scenario RCP8.5, where the increase in temperature will reach 4.5 °C in eastern Australia from 2080−2099, which is 1 °C higher than that in other cli... [more]

In this study, the influence of architectural design parameters (the exterior window area, the wall height at a corridor-side, and the door gap of a toilet unit) on the airflow patterns and malodorous volatile substance (acetic acid) distributions within toilet units were investigated via computational fluid dynamics (CFD), with the restrooms in K−12 public schools (kindergarten through grade 12) of Taiwan as research objects. The results show that when there is a 2 m/s north wind in winter, all the cases exceed the required 12 air changes per hour (ACH), and most are above 43.75 ACH. When there is a 0.5 m/s south wind in summer, nearly half of the cases fail to reach 12 ACH. Maintaining an adequate natural ventilation rate and an acceptable level of odor pollution through passive design and architectural design is difficult. Thinking about how to improve the ventilation efficiency of toilet units with the aid of simple, appropriate, and energy-saving mechanical ventilation approaches... [more]

The recent advances in computing technologies and the increasing availability of large amounts of data in smart grids and smart cities are generating new research opportunities in the application of Machine Learning (ML) for improving the observability and efficiency of modern power grids. However, as the number and diversity of ML techniques increase, questions arise about their performance and applicability, and on the most suitable ML method depending on the specific application. Trying to answer these questions, this manuscript presents a systematic review of the state-of-the-art studies implementing ML techniques in the context of power systems, with a specific focus on the analysis of power flows, power quality, photovoltaic systems, intelligent transportation, and load forecasting. The survey investigates, for each of the selected topics, the most recent and promising ML techniques proposed by the literature, by highlighting their main characteristics and relevant results. The r... [more]

In the paper, a model of a three-phase frequency-controlled induction electric drive has been developed in Simulink Matlab 2019 (MathWorks, Natick, MA, USA). This model is mathematically converted into a two-phase model by transforming equations. It is proposed to compensate the voltage drop in the power system during start-up operation under load by using supercapacitors as a buffer power source. A block of supercapacitors was calculated. Simulation modeling was performed at a different voltage than the network. The diagrams of the transient processes occurring in the electric drive when the power supply is changed were prepared. It was found that such a principle of implementing an additional source of electric energy allows to start induction electric drives in areas remote from industrial networks without significantly affecting their static and dynamic characteristics.

Empty fruit bunch, a significant by-product of the palm oil industry, represents a tremendous and hitherto neglected renewable energy resource for many countries in South East Asia and Sub-Saharan Africa. The design and simulation of a plant producing pure hydrogen through autothermal reforming (ATR) of palm empty fruit bunch (PEFB) was carried out based on successful laboratory experiments of the core process. The bio-oil feed to the ATR stage was represented in the experiments and in the simulation by a surrogate bio-oil mixture of 11 organic compounds shown to be main constituents of PEFB oil from previous work, and whose combined elemental composition and volatility was determined to be as close as possible to that of the real PEFB bio-oil. The experiments confirmed that H2 yields close to equilibrium predictions were achievable using an in-house synthetised Rh-Al2O3 catalyst in a packed bed reactor. Initial sensitivity analysis on the plant revealed that feed molar steam to carbon... [more]

The Frontier Observatory for Research in Geothermal Energy (FORGE) site is a multi-year initiative funded by the U.S. Department of Energy for enhanced geothermal system research and development. The site is located on the margin of the Great Basin near the town of Milford, Utah. Work has so far resulted in the compilation of a large amount of subsurface data which have been used to improve the geologic understanding of the site. Based on the compiled data, a three-dimensional geologic model describing the structure, composition, permeability, and temperature at the Utah FORGE site was developed. A deep exploratory well (Well 58-32) and numerous tests conducted therein provide information on reservoir rock type, temperature, stress, permeability, etc. Modeling and simulation will play a critical role at the site and need to be considered as a general scientific discovery tool to elucidate the behavior of enhanced geothermal systems and as a deterministic (or stochastic) tool to plan an... [more]

Cyberattacks against the elements of technological data transmission networks represent a rather significant threat of disrupting the management of regional electric power complexes. Therefore, evaluating the functioning quality of data transmission networks in the context of cyberattacks is an important task that helps to make the right decisions on the telecommunication support of electric power systems. The known models and methods for solving this problem have limited application areas determined by the admissible packet distribution laws. The paper proposes a new method for evaluating the quality of the functioning of data transmission networks, based on modeling the process of functioning of data transmission networks in the form of a stochastic network. The proposed method removes restrictions on the form of the initial distributions and makes the assumptions about the exponential distribution of the expected time and packet servicing in modern technological data transmission ne... [more]

Radiant cooling systems (RCS) are gaining acceptance as a heating, ventilation, and air conditioning (HVAC) solution for achieving adequate thermal comfort and maintaining acceptable indoor air quality inside buildings. RCS are well known for their energy-saving potential; however, serious condensation problem hinders the growth of this technology. In order to prevent the risk of condensation, the supply water temperature is kept higher than the dew point temperature of the air inside the room. The full potential of the cooling power of a radiant cooling panel is limited. Therefore, this article is on maximizing the cooling capacity of a radiant cooling panel, in terms of flow configuration. Radiant cooling panels (RCP) with different chilled water pipe configurations are designed and compared, side by side with the conventional serpentine flow configuration. The cooling performance of the radiant cooling panels is evaluated by using computational fluid dynamics (CFD) with Ansys Fluent... [more]

The paper presents the results of experimental and model tests of transport of dispersed fluid droplets forming a cloud of aerosol in a stream of air ventilating a selected section of the underground excavation. The excavation selected for testing is part of the ventilation network of the Experimental Mine Barbara of the Central Mining Institute. For given environmental conditions, such as temperature, pressure, relative humidity, and velocity of air, the distribution of aerosol droplet changes in the mixture of air and water vapor along the excavation at a distance was measured at 10 m, 25 m, and 50 m from the source of its emission. The source of aerosol emission in the excavation space was a water nozzle that was located 25 m from the inlet (inlet) of the excavation. The obtained results of in situ tests were related to the results of numerical calculations using computational fluid dynamics (CFD). Numerical calculations were performed using Ansys-Fluent and Ansys-CFX software. The... [more]

In this paper, we used a self-developed anisotropic cubic core holder to test anisotropic relative permeability by the unsteady-states method, and introduced the anisotropic relative permeability to the traditional numerical simulator. The oil−water two-phase governing equation considering the anisotropic relative permeability is established, and the difference discretization is carried out. We formed a new oil−water two-phase numerical simulation method. It is clear that in a heterogeneous rock with millimeter to centimeter scale laminae, relative permeability is an anisotropic tensor. When the displacement direction is parallel to the bedding, the residual oil saturation is high and the displacement efficiency is low. The greater the angle between the displacement direction and the bedding strike, the lower the residual oil saturation is, the higher the displacement efficiency is, and the relative permeability curve tends towards a rightward shift. The new simulator showed that the a... [more]

The article deals with the problems of single-phase short-circuit current distribution in overhead power lines. Short-circuit disturbances cause many negative phenomena in power networks. Since experimental studies of short-circuits in real networks are practically impossible to perform, these effects can be evaluated only theoretically, based on short-circuit current calculations with the use of appropriate mathematical models. Although short-circuit modeling is considered to be one of the simplest power system calculations, the exact mathematical description of the phenomena occurring at short-circuits is complex. Simplified normative methods are often used for short-circuit current calculations; however, this does not give ground for a thorough analysis of short-circuit current distribution in power lines. The distributions are analyzed using power line models with different degrees of complexity in line with the assumptions made for a given model. The paper presents the problem of... [more]

The charge transport in polypropylene was studied under DC electric fields at different temperatures. By the experimental measurement and simulation of the BCT model, we studied conduction currents, breakdown strength, and space charge distribution. In particular, the conduction characteristics under high temperature and high field, especially the conduction characteristics before the breakdown, were studied by systematic experiments, and the conduction characteristics and the breakdown mechanism were further studied by simulation. The results show that in the process of measuring conduction currents until breakdown, both high temperature and high electric field will promote charge transport. However, the free volume will increase at high temperature, which will easily lead to faster charge transport and breakdown. In the breakdown process at different temperatures, there are different breakdown mechanisms. At 20−60 °C, the electric breakdown process has mainly occurred in polypropylen... [more]

Plasma Pulse Geo Drilling (PPGD) is a contact-less drilling technique, where an electric discharge across a rock sample causes the rock to fracture. Experimental results have shown PPGD drilling operations are successful if certain electrode spacings, pulse voltages, and pulse rise times are given. However, the underlying physics of the electric breakdown within the rock, which cause damage in the process, are still poorly understood. This study presents a novel methodology to numerically study plasma generation for electric pulses between 200 and 500 kV in rock pores with a width between 10 and 100 μm. We further investigate whether the pressure increase, induced by the plasma generation, is sufficient to cause rock fracturing, which is indicative of the onset of drilling success. We find that rock fracturing occurs in simulations with a 100 μm pore size and an imposed pulse voltage of approximately 400 kV. Furthermore, pulses with voltages lower than 400 kV induce damage near the ele... [more]

Oil and gas well productivity can be affected by a number of different skin factors, the combined influences of which contribute to a well’s total skin factor. The skin caused by deviated wells is one such well-known factor. The present study aimed to investigate skin effects caused by deviated well slants when considering vertical-to-horizontal permeability anisotropy. The research employed computational fluid dynamics (CFD) software to simulate fluid flows in inclined wells through the injection of water with Darcy flow using 3D geometric formations. The present work investigates the effects of four main characteristics—namely, the permeability anisotropy, wellbore radius, reservoir thickness, and deviation angle—of open-hole inclined wells. Additional investigations sought to verify the effect of the direction of perforations on the skin factor or pressure drop in perforated inclined wells. In the case of an inclined open hole well, the novel correlation produced in the current stud... [more]

Natural gas sweetening is an essential process within hydrocarbon processing operations, enabling compliance with product quality specifications, avoiding corrosion problems, and enabling environmental care. This process aims to remove hydrogen sulfide (H2S), carbon dioxide, or both contaminants. It can be carried out in fixed-bed adsorption towers, where iron oxide-based solid sorbent reacts with the H2S to produce iron sulfides. This study is set out to develop a fluid-dynamic model that allows calculating the pressure drop in the H2S adsorption towers with the novelty to integrate reactivity aspects, through an iron sulfide layer formation on the solid particles’ external skin. As a result of the layer formation, changes in the particle diameter and the bed void fraction of the solid sorbent tend to increase the pressure drop. The shrinking-core model and the H2S adsorption front variation in time support the model development. Experimental data on pressure drop at the laboratory sc... [more]

Emissions pathways after COVID-19 will be shaped by how governments’ economic responses translate into infrastructure expansion, energy use, investment planning and societal changes. As a response to the COVID-19 crisis, most governments worldwide launched recovery packages aiming to boost their economies, support employment and enhance their competitiveness. Climate action is pledged to be embedded in most of these packages, but with sharp differences across countries. This paper provides novel evidence on the energy system and greenhouse gas (GHG) emissions implications of post-COVID-19 recovery packages by assessing the gap between pledged recovery packages and the actual investment needs of the energy transition to reach the Paris Agreement goals. Using two well-established Integrated Assessment Models (IAMs) and analysing various scenarios combining recovery packages and climate policies, we conclude that currently planned recovery from COVID-19 is not enough to enhance societal r... [more]

The primary task of the design and feasibility study for the use of wind power plants is to predict changes in wind speeds at the site of power system installation. The stochastic nature of the wind and spatio-temporal variability explains the high complexity of this problem, associated with finding the best mathematical modeling which satisfies the best solution for this problem. In the known discrete models based on Markov chains, the autoregressive-moving average does not allow variance in the time step, which does not allow their use for simulation of operating modes of wind turbines and wind energy systems. The article proposes and tests a SDE-based model for generating synthetic wind speed data using the stochastic differential equation of the fractional Ornstein-Uhlenbeck process with periodic function of long-run mean. The model allows generating wind speed trajectories with a given autocorrelation, required statistical distribution and provides the incorporation of daily and s... [more]

The article deals with the estimation of information quality (IQ) in information and communication technologies (ICT) systems. A number of recent publications were analyzed, as well as ISO standards concerning quality and information quality. Due to the limitations of the known methods of estimating IQ, the authors present their own proprietary concept based on multidimensional and multi-layer modeling using methods of estimating uncertainty. The modeling proposed in this publication uses sixteen dimensions of quality known from the literature. The features of dimensions are taken into account as another layer and information states as successive steps in the IQ model. An example of calculations is also presented in which the mathematical evidence method used in estimating the uncertainty is extended to the modeling of dependent elements. The article also presents a simulation based on the presented example. This simulation shows the assumed dependencies between the output and input va... [more]

Magnetohydrodynamic (MHD) phenomena, due to the interaction between a magnetic field and a moving electro-conductive fluid, are crucial for the design of magnetic-confinement fusion reactors and, specifically, for the design of the breeding blanket concepts that adopt liquid metals (LMs) as working fluids. Computational tools are employed to lead fusion-relevant physical analysis, but a dedicated MHD code able to simulate all the phenomena involved in a blanket is still not available and there is a dearth of systems code featuring MHD modelling capabilities. In this paper, models to predict both 2D and 3D MHD pressure drop, derived by experimental and numerical works, have been implemented in the thermal-hydraulic system code RELAP5/MOD3.3 (RELAP5). The verification and validation procedure of the MHD module involves the comparison of the results obtained by the code with those of direct numerical simulation tools and data obtained by experimental works. As relevant examples, RELAP5 is... [more]

Despite the extensive use of ejectors in the process industry, it is complex to predict suction and motive fluids mixture characteristics, especially with multiphase flows, even if, in most cases, mixture pressure control is necessary to satisfy process requirements or to avoid performance problems. The realization of an ejector model can allow the operators to overcome these difficulties to have real-time control of the system performance. In this context, this work proposes a framework for developing a Digital Twin of an ejector installed in an experimental plant able to predict the future state of an item and the impact of negative scenarios and faults diagnosis. ANNs have been identified as the most used tool for simulating the multiphase flow ejector. Nevertheless, the complexity in defining their structure and the computational effort to train and use them are not suitable for realizing standalone applications onboard the ejector. The proposed paper shows how Swarm Intelligence a... [more]

The aerospace industry develops prognosis and health management algorithms to ensure better safety on board, particularly for in-flight controls where jamming is dreaded. For that, vibration signals are monitored to predict future defect occurrences. However, time series are not labeled according to severity level, and the user can only assess the system health from the data mining procedure. To that extent, a clustering algorithm using a deep neural network core is developed. Time series are encoded into pictures to be fed into an artificially trained neural network: U-NET. From the segmented output, one-dimensional information on cluster frontiers is extracted and filtered without any parameter selection. Then, a kernel density estimation finally transforms the signal into an empirical density. Ultimately, a Gaussian mixture model extracts the latter independent components. The method empowered us to reveal different degrees of severity faults in the studied data, with their respecti... [more]

The production of a single gas well is influenced by many geological and completion factors. The aim of this paper is to build a production prediction model based on machine learning technique and identify the most important factor for production. Firstly, around 159 horizontal wells were collected, targeting the Duvernay Formation with detailed geological and completion records. Secondly, the key factors were selected using grey relation analysis and Pearson correlation. Then, three statistical models were built through multiple linear regression (MLR), support vector regression (SVR), gaussian process regression (GPR). The model inputs include fluid volume, proppant amount, cluster counts, stage counts, total horizontal lateral length, gas saturation, total organic carbon content, condensate-gas ratio. The model performance was assessed by root mean squared errors (RMSE) and R-squared value. Finally, sensitivity analysis was applied based on best performance model. The analysis shows... [more]

During a severe accident in a nuclear power plant, hydrogen can be generated, leading to risks of possible deflagration and containment integrity failure. To manage severe accidents, great experimental, analytical, and benchmarking efforts are being made to understand combustible gas distribution, deflagration, and detonation processes. In one of the benchmarks—SARNET H2—flame acceleration due to obstacle-induced turbulence was investigated in the ENACCEF facility. The turbulent combustion problem is overly complex because it involves coupling between fluid dynamics, mass/heat transfer, and chemistry. There are still unknowns in understanding the mechanisms of turbulent flame propagation, therefore many methods in interpreting combustion and turbulent speed are present. Based on SARNET H2 benchmark results, a two-dimensional computational fluid dynamics simulation of turbulent hydrogen flame propagation in the ENACCEF facility was performed. Four combustible mixtures with different dil... [more]

In times of unprecedented climate change and energy scarcity, the design and delivery of energy-efficient and sustainable buildings are of utmost importance. This study aimed to design a hotel building for hot and dry climate conditions and perform its energy performance analysis using energy simulation tools. The model of the hotel building was constructed by a graphical tool OpenStudio and EnergyPlus following the ASHRAE Standard 90.1. To reduce the energy demand of the hotel, parametric analysis was conducted and building envelope parameters such as the thickness of insulation layer in the exterior wall and the roof, thermal conductivity of insulation layer, rate of infiltration, U-factor of windows, and thermal resistance of air gap in the interior walls (R-value), window-to-wall ratio, and orientation of the building were tested and the impact on the energy use of the building was analyzed. It was found that most of the design assumptions based on the ASHRAE standard were already... [more]

Fuel cells, designed for mobile applications, should feature compact and low-weight designs. This study describes a design process that fulfills the specific needs of target applications and the production process. The key challenge for this type of metallic bipolar plate is that the combination of two plates creates three flow fields, namely an anode side, a cathode side, and a coolant. This illustrates the fact that each cell constitutes an electrochemical converter with an integrated heat exchanger. The final arrangement is comprised of plates with parallel and separate serpentine channel configurations. The anode and cathode sides are optimized for operation under dry conditions. The final plate offers an almost perfect distribution of coolant flow over the active area. The high quality of this distribution is almost independent of the coolant mass flow, even if one of the six inlet channels is blocked. The software employed (OpenFOAM and SALOME) is freely available and can be used... [more]