In recent years Asian Nations showed concern over the Life Cycle Assessment (LCA) of their civil infrastructure. This study presents a contextual investigation of a residential apartment complex in the territory of the southern part of India. The LCA is performed through Building Information Modelling (BIM) software embedded with Environmental Product Declarations (EPDs) of materials utilized in construction, transportation of materials and operational energy use throughout the building lifecycle. The results of the study illustrate that cement is the material that most contributes to carbon emissions among the other materials looked at in this study. The operational stage contributed the highest amount of carbon emissions. This study emphasizes variation in the LCA results based on the selection of a combination of definite software-database combinations and manual-database computations used. For this, three LCA databases were adopted (GaBi database and ecoinvent databases through One... [more]

The United Nations Sustainable Goal 7, access to affordable and clean energy, is unlikely to be achieved, with an estimated 600 million people still without access to electricity by 2030. One potential route to support this goal is through the use of mini-grids to provide electricity in densely populated rural areas for which grid connection is not possible. This paper presents the results of a life cycle assessment of a mini-grid, designed for construction in Malawi. It analyses the cradle to end of use for this mini-grid configuration, for a grid sized for lighting, refrigeration and phone charging, and for a grid sized for electric cooking (e-cooking). The results suggest that for lighting configuration, the main contributors to environmental impact are the poles, the overhead cabling, and the PV panels. The use of a chromium-based preservative is the main issue for the poles, and a switch to concrete poles can deliver significant benefits. When the grid is sized for e-cooking, the... [more]

Swimming pools are used around the world for recreational, rehabilitation and physical activity. From an energy and environmental standpoint, grey water as a waste thermal potential of swimming pools is a valuable heat source produced continuously in extensive, measurable and large quantities. The main objective of this article is to analyse the feasibility of proposed grey water heat recovery (GWHR) system from the showers and backwater from swimming pool filters for an indoor pool located in recreation centre in Poland. Analysis, calculations and results were obtained and discussions of water and energy consumption were carried out for the mentioned indoor swimming pool on the basis of real measurements case study for water flow rate, water temperature in swimming pools and showers. The results ensure a significant potential of energy savings by using the proposed GWHR system, which allows to reduce the energy demand by 34% up to 67% for pool water preheating and domestic hot water (... [more]

Understanding the influence of method choices on results in life-cycle assessments is essential to draw informed conclusions. As the climate impact of bioenergy remains a debated topic, the focus of this study is how the chosen temporal framing influences a comparison of the climate impact of utilizing residual biomass for biofuel production to that of leaving the biomass to decay. In order to compare the biofuel scenario to its corresponding reference scenario where biomass is left to decay, a variety of analytical approaches were used: using time-aggregated and time-dependent life-cycle inventories and climate-impact assessment methods, assuming biogenic carbon to be climate neutral or not, using metrics for cumulative or instantaneous climate impact, and with different time horizons. Two cases of residual biofuel feedstocks were assessed: logging residues from Norway spruce forest, and straw from wheat cultivation. Consideration of the studied method choices appears to be especially... [more]

Reducing energy waste is one of the primary concerns facing Remote Industrial Plants (RIP) and, in particular, the accommodations and operational plants located in remote areas. With the COVID-19 pandemic continuing to attack the health of workforce, managing the balance between energy efficiency and Occupation Health and Safety (OHS) in the workplace becomes another great challenge for the RIP. Maintaining this balance is difficult mainly because a full awareness of the OHS will generally consume more energy while reducing the energy cost may lead to a less effective OHS, and the existing literature has not seen a system that is designed for the RIPs to conserve energy usage and improve workforce OHS simultaneously. To bridge this gap, in this paper, we propose an AI Empowered Cyber Physical Ecosystem (AECPE) solution for the RIPs, which integrates Cyber-Physical Systems (CPS), artificial intelligence, and mobile networks. The preliminary results of lab experiments and field tests pro... [more]

Air pollution caused by vehicle emissions has raised serious public health concerns. Vehicle emissions generally depend on many factors, such as the nature of the vehicle, driving style, traffic conditions, emission control technologies, and operational conditions. Concerns about the certification cycles used by various regulatory authorities are growing due to the difference in emission during certification procedure and Real Driving Emissions (RDE). Under laboratory conditions, certification tests are performed in a ‘chassis dynamometer’ for light-duty vehicles (LDVs) and an ‘engine dynamometer’ for heavy-duty vehicles (HDVs). As a result, the test drive cycles used to measure the automotive emissions do not correctly reflect the vehicle’s real-world driving pattern. Consequently, the RDE regulation is being phased in to reduce the disparity between type approval and vehicle’s real-world emissions. According to this review, different variables such as traffic signals, driving dynamic... [more]

In Europe, buildings are responsible for more than one third of the total final energy demands and greenhouse gas emissions. In the last twenty years, the European Union has published a succession of energy performance of building directives to define and ensure the fulfilment of a series of objectives regarding greenhouse gas emissions, energy consumption, energy efficiency and energy generation from renewable sources in buildings. For its part, Spain is adapting its legal framework, transposing these directives with the aim of achieving greater energy efficiency and sustainability for buildings. Under this context, an energy, economic and environmental assessment is performed to analyze the impact of these regulatory changes on a single-family home including a photovoltaic installation for self-consumption with surpluses and/or a solar thermal installation for domestic hot water supply, located in each one of the eight thousand one hundred thirty-one municipalities that make up Spain... [more]

Geo-resources are widely exploited in our society, with huge benefits for both economy and communities. Nevertheless, with benefits come risks and impacts. Understanding how such risks and impacts are intrinsically borne in a given project is of critical importance for both industry and society. In particular, it is crucial to distinguish between the specific impacts related to exploiting a given energy resource and those shared with the exploitation of other energy resources. A variety of different approaches can be used to identify and assess such risks and impacts. In particular, Life Cycle Assessment (LCA) and risk assessments (RAs) are the most commonly adopted. Although both are widely used to support decision making in environmental management, they are rarely used in combination perhaps because they have been developed by largely different groups of specialists. By analyzing the structure and the ratio of the two tools, we have developed an approach for combining and harmonizin... [more]

Cooking with modern energy fuels and technologies has a high potential to positively impact the users’ health and well-being, and make cooking safer and less burdensome for women and girls. To date, there have been numerous interventions targeting improved cooking solutions in displacement settings, but very few which have involved modern energy cooking, such as ethanol, biogas, LPG or electric cooking. They have been largely absent from humanitarian programming due to limited availability, affordability and lack of business models that suit those complex settings. Additionally, energy access services in displacement settings have historically relied primarily on grant-based funding. However, grants are limited to relatively short timeframes which do not align with the long-term needs of the displaced. New ways of funding energy access in displacement settings, and particularly modern energy cooking services, are urgently needed to address the scale of the challenge as the number of di... [more]

After the Great Recession of 2008, there was a strong commitment from several international institutions and forums to improve wellbeing economics, with a switch towards satisfaction and sustainability in people−planet−profit relations. The initiative of the European Union is the Green Deal, which is similar to the UN SGD agenda for Horizon 2030. It is the common political economy plan for the Multiannual Financial Framework, 2021−2027. This project intends, at the same time, to stop climate change and to promote the people’s wellness within healthy organizations and smart cities with access to cheap and clean energy. However, there is a risk for the success of this aim: the Jevons paradox. In this paper, we make a thorough revision of the literature on the Jevons Paradox, which implies that energy efficiency leads to higher levels of consumption of energy and to a bigger hazard of climate change and environmental degradation.

The reliance on coal-fired power generation has gradually reduced with the growing interest in the environment and safety, and the environmental effects of power generation are now being considered. However, it can be difficult to provide stable power to end-users while minimizing environmental pollution by replacing coal-fired systems with combined cooling, heat, and power (CCHP) systems that use natural gas, because CCHP systems have various power output vulnerabilities. Therefore, purchasing power from external electric grids is essential in areas where CCHP systems are built; hence, optimal CCHP controls should also consider energy purchased from external grids. This study proposes a two-stage algorithm to optimally control CCHP systems. In Stage One, the optimal energy mix using the Lagrange multiplier method for state-wide grids from which CCHP systems purchase deficient electricity was calculated. In Stage Two, the purchased volumes from these grids were used as inputs to the pr... [more]

Seismic energy propagation from the hypocentre of mining-induced tremors usually causes an uneven distribution of the peak ground velocity PGVHmax in tectonically complicated structures, and consequently, an uneven distribution of damage to buildings located on the ground surface. This study aimed to estimate the impact of high-energy mining-induced tremors in fault zones on damage to buildings. In the study, we describe a case of one of the highest-energy mining-induced tremors E = 4.0 · 108 J (local magnitude ML = 3.6) that occurred in the Upper Silesian Coal Basin (USCB), Poland. The hypocentre of the tremor was most probably located in the Barbara fault zone, one of the larger faults in that western part of the USCB. Numerous damaged buildings on the terrain surface were registered, both in the epicentral zone and at a greater distance from the epicentre, mostly from the southern side of the Barbara fault zone. We calculated that the tremor was characterised by a normal slip mechan... [more]

The impact of natural CO2 emissions in the development of geothermal areas is presently gaining more attention than ever before. In Italian geothermal fields, a reduction in the natural CO2 emissions has been observed. This paper reviews and provides an analysis of the historical production data of boric acid from 1818 to 1867 used to calculate the natural emissions of CO2 associated with boric acid production that pre-dates the use of geothermal resources for power production, which started in 1913. Boric acid was already being extracted from the natural geothermal fluids in geysers and natural ponds emitting steam and gases. After 1827 the ‘lagone coperto’ (covered lake) equipment optimized production, and the drilling of shallow wells (20−30 m) starting in 1836, which further increased the quantity of its extraction. The first geothermal reservoir was developed at the turn of the century and the Larderello geothermal field began to grow. The use of deep wells, keeping pace with the... [more]

In many regions of the world, the winter period is a time of poor air quality, due primarily to the increased use of individual and district heating systems. As a consequence, the atmospheric air contains increased concentrations of both particulate matter and gaseous pollutants (as a result of “low” emissions at altitudes of up to 40 m and “high” emissions more than 40 m above ground level). In winter, the increased pollution is very often exacerbated by meteorological conditions, including air temperature, pressure, air speed, wind direction, and thermal inversion. Here, we analyze the concentrations of particulate matter (PM10, PM2.5, and PM1.0) and gaseous pollutants (H2S, SO2, and VOC) in the immediate vicinity of a large solid fuel-fired heat and power plant located in an urban agglomeration. Two locations were selected for analysis. The first was close to an air quality measurement station in the center of a multi-family housing estate. The second was the intersection of two mai... [more]

This paper presents a new virtual reality (VR)-based approach to advanced learnings and experiences of the circular economy (CE) in the construction industry. The approach involves incorporating game design and a building information modelling (BIM) digital twin of a purposed CE prototype building. Our novel approach introduces VR environments designed to provide a visual representation of materials and components that can be reintroduced into the supply chain at the end of life and their removal procedures and material provenance. A case study methodology was applied to a purposely designed CE building, namely the Legacy Living Lab (L3). To reflect the real-life building, L3’s BIM model was combined with Unify game software to advance the literature in three key areas. First, the research investigates VR tools that will allow building designers to view and implement their strategies to advance CE design. Second, this research proposes an advanced VR tool to visualise the bill of quant... [more]

In this review paper, we select four important waves of new entrants that knocked on the door of European electricity markets to illustrate how market rules need to be continuously adapted to allow new entrants to come in and push innovation forward. The new entrants that we selected are utilities venturing into neighbouring markets after establishing a strong position in their home market, utility-scale renewables project developers, asset-light software companies aggregating smaller consumers and producers, and different types of communities. We show that well-intentioned rules designed for certain types of market participants can (unintentionally) become obstacles for new entrants. We conclude that the evolution of market rules illustrates the importance of dynamic regulation. At the start of the liberalisation process the view was that we would deregulate or re-regulate the sector after which the role of regulators could be reduced. However, their role has only increased. New playe... [more]

Due to the rapid increase in the consumption of electrical energy and the instability of fossil fuel prices, renewable energy, such as wind power (WP), has become increasingly economically competitive compared to other conventional energy production methods. However, the intermittent nature of wind energy creates certain challenges to the power network operation. The combined economic environmental dispatch (CEED) including WP is one of the most fundamental challenges in power system operation. Within this context, this paper presents a new attempt to solve the probabilistic CEED problem with WP penetration. The optimal WP to be incorporated in the grid is determined in such a way that the system security is within acceptable limits. The system security is described by various fuzzy membership functions in terms of the probability that power balance cannot be met. These membership functions are formulated based on the dispatcher’s attitude. This probabilistic and non-convex CEED proble... [more]

This study assessed whether methods for capturing the pedestrian experience of outdoor lighting, previously evaluated in a full-scale laboratory, were applicable in a real-world setting. It applied an approach capturing the human response to outdoor lighting in a systematic way, by assessing perception, evaluation and behaviour in the lit environment. The study involved 81 participants from two age groups (Young—n: 48, mean age: 26, 63% women; Elderly—n: 33, mean age: 69, 67% women) and was carried out on a pedestrian path in a park in the centre of Malmö, Sweden, in the evenings during wintertime. Two LED lighting applications, differing in light distribution, uniformity and horizontal illuminance, were presented, and the pedestrians’ perception (facial expression recognition and sign reading), evaluation (arousal, valence and perceived outdoor lighting quality) and behaviour (pedestrian flow) were assessed. The results from the perceptual tasks differed significantly between the ligh... [more]

A number of new rural management models have emerged to solve the problems of economic backwardness, insufficient resource utilization, and technical shortages in rural areas in the context of poverty alleviation to the rural revitalization strategy in China. However, the influence of new rural management model under all countermeasures for rural sustainable development with a comprehensive perspective is lacking. Therefore, exploring whether the new rural management model meets the requirements of sustainable development is an urgent issue. From the theory of system metabolism and emergy accounting method, this study classified the government funds for poverty alleviation measures as import resources, and analyzed the metabolic structure, efficiency, and the rural development factors of Chehe Village before and after poverty alleviation measures are carried out (the year of 2012 and 2019) to verify whether the new model was sustainable. According to the results of this study, the new... [more]

In order to reduce the energy consumption of HVAC systems in buildings, the use of energy-saving solutions is necessary. One of these solutions is ventilation, which is usually used for maintaining acceptable indoor air quality and thermal comfort. As the change in outdoor environment is unpredictable and the occupant control is spontaneous, it is critical to control the windows and HVAC systems to achieve a maximum use of outdoor air for indoor ventilation. A new rule-based control strategy that could change the opening factor of windows is proposed in this study and its effectiveness was tested in five representative climates, ranging from a subtropical region to a severely cold region. A building model was set up and the indoor air temperature and energy consumption were predicted using EnergyPlus. The results show that the proposed control strategy can utilize ventilation to maintain a comfortable indoor environment with an annual uncomfortable percentage in an occupied period lowe... [more]

The issue discussed in this article concerns corporate social responsibility (CSR), which is playing an increasingly important role in the context of sustainable development of enterprises. The purpose of the current work was to assess the practices applied in the area of corporate social responsibility in water and sanitation companies, based on the opinions of employees and managers. The motivation for undertaking research on this topic resulted from the scarcity of scientific studies on the measurement of the corporate social responsibility concept in water and sanitization companies using a multidimensional approach based on the ISO 26000 standard. The study used methodological triangulation based on the use of qualitative and quantitative research methods to verify information from different sources. This approach allowed the authors to obtain the data more effectively and analyze the problem from numerous different perspectives. The study used an interview method that targeted wa... [more]

Global warming, as the result of the negative impact of humans on climate change, has been observed based on various data sources. Various measures have aimed to reduce anthropogenic factors, and also to lower carbon dioxide (CO2) and methane CH4 emissions. One of the main contributors to anthropogenic factors is organic waste in municipal solid waste landfills. There are many landfills where cost-effective rapid technologies for the identification and quantification of CH4 emission sites are not applied. There is still a need for the development of accessible and cost-effective methods that react in a real-time manner for the rapid detection and monitoring of methane emissions. This paper’s main goal is to create a prototype sensor suitable for operational measurement of the gas value, suitable for integration into geodetic equipment or an unmanned aerial vehicle system. A sensor system (device) was developed, which consisted of three semiconductor sensors—MQ2, MQ4, and MQ135—which ai... [more]

Energy markets play an important role in achieving sustainable development goals. The sector of energy has a huge impact on the environment, hence changes in it are the highest priority in the European Union. The process of shaping and developing the internal energy market plays an important role in improving the security of supply of energy resources for the entire union. It requires a number of political negotiations, strategic decisions regarding energy liberalization, in particular, the electricity and gas sectors, as well as the adoption of sectoral legislation. The aim of the conducted research is to estimate the level of development of energy markets in the EU countries and to indicate the position of Poland in comparison to other countries. The research was performed in several stages. The first phase consisted of selecting appropriate diagnostic variables that comprehensively describe energy markets in countries belonging to the European Union. The next stage was collecting da... [more]

The urban population increase in the world, the economic expansion, and the rise in living standards associated with society’s habits and lifestyles accelerated the municipal solid waste (MSW) generation in undeveloped countries, such as in Brazil, in which the generation increased by 25% from 2012 to 2017. In the same period, the São Paulo state, the richest Brazilian state, increased its municipal solid waste generation by 51%. All this MSW needed to be collected and transported, and this process has a high economic and environmental cost. Therefore, this study aims to identify, using spatial analysis, the routes used by MSW trucks to estimate the distances traveled to dispose of the MSW on a regional scale considering all municipalities in the São Paulo state. The findings showed that the landfill numbers decrease, mainly individual ones, which receive MSW only from the city where it is located. Otherwise, the consortium landfills number is increasing, as well as the number of munic... [more]

The purpose of this investigation is to propose a way for acquiring the foremost window allocation scheme to have the best trade-off among energy, environmental, and comfort criteria in a building. An advanced decision-making tool, named the technique for order preference by similarity to ideal solution (TOPSIS), is utilized to find the best building amongst different alternatives for having windows on the building façades. Three conditions, namely two parallel, two perpendicular, and three façades, considered as A, B, and C types, respectively, are investigated. For each type, four possible orientations are studied. Heating, cooling, and lighting energy demands in addition to carbon dioxide equivalent emission and thermal and visual comfort are taken into account as the investigated criteria, and they are all evaluated in a simulation environment. The results show that for the modular residential buildings chosen as the case study and located in Tehran, Iran, having windows on the nor... [more]