In the world, as in Lithuania, there is a costant search for new crops suitable for energy conversion. The coarse-energy crops and their biomass studied for this paper were assessed in a comprehensive manner, i.e., not only their calorific value and ash content but also their ash melting properties and pollutants emitted during the thermochemical conversion. The calorific value of energy crops varies from 17.92 ± 0.32 to 18.50 ± 0.66 MJ kg−1 and decreases in the following order: A. dubia > M. giganteus > C. sativa. Ash content varies from 1.51 ± 0.03 to 3.36 ± 0.23% and decreases in the following order: C. sativa > A. dubia > M. giganteus. The lowest primary ash deformation (648 ± 8 °C) was recorded for C. sativa. Taking into account the specificity of our research and the changes in biomass ash content due to mineral nitrogen fertilization, it has been found that that higher levels of nitrogen fertilizers in the combustion products reduce CO and increase the total CO2 content of the c... [more]

In December 2019, the European Commission unveiled an ambitious project, the European Green Deal, which aims to lead the European Union to climate neutrality by 2050. This is a significant challenge for all EU countries, and especially for Poland. The role of hydrogen in the processes of decarbonization of the economy and transport is being discussed in many countries around the world to find rational solutions to this difficult and complex problem. There is an ongoing discussion about the hydrogen economy, which covers the production of hydrogen, its storage, transport, and conversion to the desired forms of energy, primarily electricity, mechanical energy, and new fuels. The development of the hydrogen economy can significantly support the achievement of climate neutrality. The belief that hydrogen plays an important role in the transformation of the energy sector is widespread. There are many technical and economic challenges, as well as legal and logistical barriers to deal with in... [more]

Utilizing underground coal gasification cavities for carbon capture and sequestration provides a potentially economic and sustainable solution to a vexing environmental and energy problem. The thermal influence on creep properties and long-term permeability evolution around the underground gasification chamber is a key issue in UCG-CCS operation in containing fugitive emissions. We complete multi-step loading and unloading creep tests with permeability measurement at confining stresses of 30 MPa on pre-cracked sandstone specimens thermally heat-treated to 250, 500, 750 and 1000 °C. Observations indicate a critical threshold temperature of 500 °C required to initiate thermally-induced cracks with subsequent strength reduction occurring at 750 °C. Comparison of histories of creep, visco-elastic and visco-plastic strains highlight the existence of a strain jump at a certain deviatoric stress level—where the intervening rock bridge between the twin starter-cracks is eliminated. As the devi... [more]

In recent years, the use of biodegradable fluids as liquid insulation for distribution and power transformers is spreading. The main biodegradable fluids used are natural and synthetic esters, although biodegradable hydrocarbons have been recently proposed. Biodegradable fluids have a much lower environmental impact than mineral oil, limiting the risk of soil contamination in leaks, which makes them a suitable solution for applications such as offshore transformers or railway transformers. Additionally, these fluids have a higher flash point than conventional mineral oils, which dramatically reduces the risk of fire and collateral damage derived from explosion and fire. Despite these advantageous factors, there are still some aspects that hinder the broadening of their use, such as the difference in thermal properties or the lack of accepted maintenance procedures for transformers that use them as liquid insulation. This paper presents the current status of biodegradable insulating flu... [more]

Isolation of spent nuclear fuel assemblies in deep vertical boreholes is analyzed. The main safety features of the borehole concept are related to the repository’s great depth, implying (a) long migration distances and correspondingly long travel times, allowing radionuclides to decay, (b) separation of the repository from the dynamic hydrological cycle near the land surface, (c) stable geological and hydrogeological conditions, and (d) a geochemically reducing environment. An integrated simulation model of the engineered and natural barrier systems has been developed to examine multiple scenarios of the release of radionuclides from the waste canisters, the transport through a fractured porous host rock, and the extraction of potentially contaminated drinking water from an aquifer. These generic simulations include thermal effects from both the natural geothermal gradient and the heat-generating waste, the influence of topography on regional groundwater flow, moderated by salinity str... [more]

The physical environment of classrooms has a strong relationship with student learning performance and health. Since the outbreak of COVID-19 in 2019, almost all universities have begun implementing closed instructional management, which has forced students to spend a much longer amount of time inside the classroom. This has also led to an increasing problem of thermal comfort in classroom indoor environments. In this paper, classrooms evolved from three dominant teaching modes at Zhejiang Sci-Tech University (ZSTU), located in the Hot Summer and Cold Winter (HSCW) zone of China, were selected as experimental spaces. Meanwhile, 12 learning groups with 60 students (30 of each sex) were selected as the tested samples. The relationship between thermal comfort and learning efficiency of the tested students was established through thermal comfort questionnaires and learning efficiency tests under the typical natural conditions in transition seasons. Based on this, improvement strategies wer... [more]

A new DC fault current limiter (FCL)-based circuit breaker (CB) for DC microgrid (MG) clusters is proposed in this paper. The analytical expressions of the DC fault current of a bidirectional interlink DC/DC converter in the interconnection line of two nearby DC MGs are analyzed in detail. Meanwhile, a DC fault clearing solution (based on using a DC FCL in series with a DC circuit breaker) is proposed. This structure offers low complexity, cost, and power losses. To assess the performance of the proposed method, time-domain simulation studies are carried out on a test DC MG cluster in a MATLAB/Simulink environment. The results of the proposed analytical expressions are compared with simulation results. The obtained results verify the analytical expression of the fault current and prove the effectiveness of the proposed DC fault current limiting and clearing strategy.

The present paper deals with issues related to activities undertaken by local government. The article focuses on the identification and assessment of the significance of local government’s different bottom-up initiatives that support development of local entrepreneurship. The article also indirectly discusses the importance of activities referring to energy efficiency. Through the digitization process and by using digital tools, LGs realize projects, improve local actors’ awareness, and finally achieve new challenges such as a higher proportion of gross final energy consumption being from renewable sources. The aim of the paper is to present the relationship between the LGs’ entrepreneurial activities, which we call bottom-up initiatives, and the local entrepreneurship level, understood as the number of entrepreneurs active on the territory of a LG. This paper presents the results of research carried out on the bottom-up initiatives undertaken by Polish local governments to support ent... [more]

A significant challenge for the DSO (Distribution System Operator) will be to choose the optimum strategy for flexibility service in the LV area with high RES (renewable energy sources) penetration. To this end, a representative LV grid operated in Poland was selected for analysis. Three research scenarios with RES generation were presented in the range of 1−8 kW for the power factor from 0.9 to 1. The grid PV capacity was determined for four load profiles. Based on this factor, optimum RES volume management service types were determined. Under the flexibility service, the proposed power conversion services and active RES operations for DSO were proposed. The research was conducted using the Matlab and PowerWorld Simulator environment. Optimum active power values were obtained for the RES generation function for single and dual operation systems of the power conversion system. In future, the knowledge in the field of grid capacity will enable the DSO to increase the operating efficienc... [more]

This study investigated the evaporative heat transfer coefficient and pressure drop characteristics of R-1234yf in a horizontal tube with an inner diameter of 6.95 mm under various experimental conditions. The heat transfer coefficient increased with an increase in quality but showed a sharp decrease in the high-quality area. In addition, the heat transfer coefficient increased as the mass flux, heat flux, and saturation temperature increased. Although R-1234yf and R-134a presented similar heat transfer coefficients, that of R-134a was higher. The pressure drop increased with an increase in the quality and mass flux but decreased with an increase in the saturation temperature. The pressure drop of R-134a was larger than that of R-1234yf. In light of the flow pattern diagram by Taitel and Dukler, most of the experiments were included in the annular flow region, and some regions showed intermittent and stratified corrugated flow regions. Kandlikar’s heat transfer coefficient correlation... [more]

Power Internet of Things (IoT) is the application of IoT technology in the field of power grid, which can better control all kinds of power equipment, power personnel and operating environment. However, access to mass terminals brings higher requirements for terminal authentication and key management for the power IoT. And the traditional public key infrastructure (PKI) and identity-based public key cryptography (IB-PKC) exist the problems of certificate management and key escrow. Therefore, the paper proposes a novel authenticated key agreement scheme based on the certificateless public key cryptography (CL-PKC) mechanism. In addition, the proposed scheme is proven with the improved extended Canetti-Krawczyk (eCK) security model. Finally, the implementation of the authenticated key agreement protocol is given based on the actual application requirement of the power IoT, and the analysis and comparison of the simulation demonstrates that the proposed scheme has higher efficiency and wo... [more]

Calculation and measurement of the overhead power lines electrical parameters is common practice in today’s electrical engineering industry; however, there is very little data to actually compare these two approaches because measured data in such detail are mostly unavailable for academic purposes. Based on the very detailed model of an overhead power line in MATLAB Simulink environment and conducted experimental measurement, this article specifically covers the exact evaluation of the impedance of the investigated overhead power line. Differences between calculation and experimental measurement are shown and discussed accordingly, where, surprisingly, the biggest deviation was observed in the positive resistance parameter. The connection between different measurement techniques (multiple single-phase and three-phase methods), as well as the power line asymmetry reflection in the impedance matrix is explained as well as compared to expected values from the computations. The complete ma... [more]

Increasing economic and population growth has put immense pressure on energy, water and land resources to satisfy national and supra-national demand. Through trade, a large proportion of such a demand is fulfilled. With trade as one of its key priorities, the China Belt and Road Initiative is a long-term transcontinental investment program. The initiative gained significant attention due to greater opportunities for economic development, large population and different levels of resource availability. The nexus approach has appeared as a new viewpoint in discussions on balancing the competing sectoral demands. However, following years of work, constraints exist in the scope and focus of studies. The newly developed multi-regional input−output (MRIO) models covering the world’s economy and its use of resources permit a comprehensive analysis of resource usage by production and consumption at different levels, and bring more knowledge about resource nexus problems. Using the MRIO model, t... [more]

The advancements in sensor and communication technologies drive the rapid developments in the applications of occupancy and indoor environmental monitoring in buildings. Currently, the installation standards for sensors are scarce and the recommendations for sensor positionings are very general. However, inadequate sensor positioning might diminish the reliability of sensor data, which could have serious impacts on the intended applications such as the performance of demand-controlled HVAC systems and their energy use. Thus, there is a need to understand how sensor positioning may affect the sensor data, specifically when using multi-sensor devices in which several sensors are being bundled together. This study is based on the data collected from 18 multi-sensor devices installed in three single-occupant offices (six sensors in each office). Each multi-sensor device included sensors to measure passive infrared (PIR) radiation, temperature, CO2, humidity, and illuminance. The results sh... [more]

Sewage sludge from wastewater treatment plants is commonly used as a soil amendment on agricultural land. Unfortunately, more and more research indicates that large amounts of microplastic (MP) are re-introduced to soil with sludge. This study aims to present the impact MP has on soil ecosystems, global trends in agricultural sludge management resulting from a high concentration of micropollutants in sludge, and finally propose a high-level strategy for sustainable sludge management. This strategy is mostly dedicated to the European Union and involves multiple stakeholders and the links between each of them to achieve appropriate sludge management to avoid soil pollution with MP. Governance, Technology, Consumer Acceptance, and Economy and Commercial Viability is explored in depth. To the author’s knowledge, this is the first paper to discuss these topics in the context of a changing agricultural scene and identifies ways of which sewage sludge can limit MP pollution whilst still fitti... [more]

The integration of renewables into power systems is a key transformation for mitigating climate change and reducing fossil-fuel dependence. Among the different resources, wind participation has become crucial in recent decades—both onshore and offshore wind power plants. However, assuming the useful life of the wind turbines at approximately 20 years, different solutions should be discussed to overcome the turbine’s aging problem. In the coming years, some countries within the wind sector will face the decision of partially or totally repowering or dismantling their turbines. This paper reviews different repowering strategies and contributions from a multifactorial perspective. A set of categories is defined by the authors and those multifactorial parameters are then classified according to such categories: technical, economic, environmental, social, and political. From each category, the most relevant factors to be considered for repowering decision-making purposes are identified and... [more]

Poland has had a total of 70 mines, but now more than half of them is out of operation. This mining closure raises with respect to the environment and unemployment. Innovative technology is needed to overcome the problems that arise and could simultaneously make use of abandoned mine infrastructure. The increased electricity generation coming from renewable energy, which produces fluctuating and intermittent energy for the electric power system, causes frequency problems such that energy storage technologies are needed. Abandoned mines can be used for the implementation of energy storage plants. This paper explores the possibility of using abandoned mines in Poland for electrical energy storage. Closed mines can be used to store clean and flexible energy. This idea has the potential to support sustainable economic development within the community following mine closure in Poland.

Corporate social responsibility (CSR) assumes that companies should justify their existence with services for various stakeholders and not with profit alone. There is a strong emphasis on the implications of CSR for managing human resources in hotels and other accommodation services, supporting local communities, and promoting environmental sustainability. This article aims to present the adjustment of business entities providing accommodation services in Poland to the CSR principles. Two aspects were examined: the environmental aspect, i.e., waste segregation and the use of economic energy receivers, while the social aspect included engaging employees, as well as investing in improving their qualifications towards pro-ecological awareness. The study was conducted on a sample of 207 owners and managers of economic entities in the accommodation sector in Poland. The Statistica software was used to analyze the obtained results, including Chi2 statistics and correspondence analysis. Based... [more]

An urgent demand for recycling spent lithium-ion batteries (LIBs) is expected in the forthcoming years due to the rapid growth of electrical vehicles (EV). To address these issues, various technologies such as the pyrometallurgical and hydrometallurgical method, as well as the newly developed in-situ roasting reduction (in-situ RR) method were proposed in recent studies. This article firstly provides a brief review on these emerging approaches. Based on the overview, a life cycle impact of these methods for recovering major component from one functional unit (FU) of 1 t spent EV LIBs was estimated. Our results showed that in-situ RR exhibited the lowest energy consumption and greenhouse gas (GHG) emissions of 4833 MJ FU−1 and 1525 kg CO2-eq FU−1, respectively, which only accounts for ~23% and ~64% of those for the hydrometallurgical method with citric acid leaching. The H2O2 production in the regeneration phase mainly contributed the overall impact for in-situ RR. The transportation di... [more]

This study investigated the contributions of human capital and physical capital to economies at different stages by measuring the economic development with the traditional GDP and green GDP. The traditional GDP stood for the quantity of economic growth, and the green GDP, taking both the energy consumption and environmental pollution into account, was employed to represent the sustainability of economic development. We used a panel data of 143 countries and regions during the period from 1990 to 2014, and results showed that the elasticities of output with respect to human capital were greater compared to physical capital, while green GDP was significantly more sensitive to changes in human capital than the traditional GDP. In particular, considering the unbalanced distribution of economic growth among countries and regions, we employed the quantile regression model to explore the heterogeneous roles of physical and human capital in different stages of economic development, which evide... [more]

Increasing participation in demand response within the industrial sector may be crucial to growing the levels of available flexible capacity required to reliably control national electricity grids as renewable generation increases to satisfy emission targets. This research aims to assist the uptake of demand response in the industrial sector by investigating risk to indoor thermal environments on industrial sites offering air handling unit capacity for demand response. This evaluation uses a systematic model-based approach, calibrated and validated with empirical data from a relevant case study industrial building to assess risk through a number of scenarios. The conditions investigated cover several relevant grid response times and durations, and national and international extreme external ambient temperatures in the past, present and future under a variety of temperature limits. The study demonstrated that there is very low risk to the case study site participating in demand response... [more]

Experiments were carried out to investigate the heat transfer and pollutants emission characteristics of a slot LPG premixed flame array impinging normally onto a flat plate. The effects of jet-to-jet spacing (S/de), nozzle-to-plate distance (H/de), and jet Reynolds number (Re) on the heat flux and emission index of CO, CO2, and NOx/NO2 were examined. In addition, the thermal and emission characteristics between slot jets and circular jets were compared under identical experimental conditions. The results show that the more uniform heat flux distribution and higher total heat flux can be obtained at moderate jet-to-jet spacing, large jet-to-plate distance, and higher Reynolds number. EICO emissions can be influenced by the combined effects of jet-to-jet spacing, jet-to-plate distance, and higher Reynolds number. For the sake of the better combustion efficiency and lower EICO emission, the moderate jet-to-jet spacing (S/de = 2.5), larger jet-to-plate distance (H/de = 4), and relatively... [more]

This study provides an in-depth assessment of the environmental performance of five public schools in the transition towards a low-carbon economy and a more sustainable model of society. Life cycle assessment (LCA) methodology is used to conduct the study. The school system includes several activities and processes clustered in three subsystems: management of the school building, training and learning activities (T&L) and mobility and transport (M&T). A detailed primary data inventory of energy and resources consumption was collected in five schools located in Spain and Portugal. Findings on climate change (CC), water depletion (WD), particular matter (PM), acidification (Ac), and human health (HH), as well as associated external cost (EC), are reported per student in one school year as reference unit, allowing the schools’ individual performance comparison and identify the potential improvements. Considering the sample of schools, findings reveal that peculiarities of the schools, suc... [more]

Although eco-friendly (pro-environmental) behaviour in tourism has attracted interest among practitioners and scholars, little is known about the influence of these attitudes on the choice of eco-friendly destinations, especially in the context of emerging tourist markets such as India. Thus, this article aims to verify a model of the relationships between attitudes towards the environment and eco-friendly tourism, social and personal norms regarding environmentally responsible behaviour, perceived behavioural control, behavioural intentions regarding eco-friendly destinations and the willingness to pay for such trips using the theory of planned behaviour. The study used an online survey conducted with 598 Indians. The relationships between the variables were analysed using PLS-PM. The most important results indicated that (1) there are significant relationships between the attitude towards the environment, the attitude towards an eco-friendly destination, social and personal norms and... [more]

The present work involves a new and novel upgrading design to the classical solar chimney power plant (SCPP) structure. The SCPP design was modified by adding a co-centric secondary external chimney to the SCPP structure to enhance energy production. In the new improved design, named the solar double-chimney power plant (SDCPP), the internal chimney, operates like a traditional SCPP to produce electricity during the daytime whereas the secondary external chimney operates as 10 cooling towers (CT) in a series. Each CT is equipped with a turbine and water sprinklers for further energy production. The new design offers the operation of the SCPP during the day and the continuous operation of the CT (day-and-night). A mathematical model that includes the energy and mass balance equations of the system was built using MATLAB. The SDCPP system produced up to 993 MWh of electrical energy, which is 2.6 times higher than the traditional SCPP (377 MWh). The new design configuration achieved a per... [more]