With the gradual increasing of the transmission voltage level, the situation of interference on secondary side equipment in smart substations is becoming more serious. The authors tested the interference waveforms caused by the circuit breaker’s operation at the smart substation, which showed the severity of the electromagnetic (EM) environment. This paper takes the electronic current transformer acquisition card as an example. The influence of EM interference sources on the reliability of the acquisition card is analyzed. Then, standardized electromagnetic compatibility (EMC) immunity tests of the international electrotechnical commission (IEC) for different interferences are implemented. Typical output characteristics of acquisition cards for different tests are analyzed. Innovatively, this paper proposes a quantitative evaluation method of output waveform disturbance to evaluate the acquisition card’s performance. This disturbance distortion is of great significance to the EM enviro... [more]

Heat damage in deep mines is severe and can lead to adverse health effects. The existing refrigeration schemes for the heading face in excavation roadways aim to cool the whole cooling region. However, the ratio of the area occupied by workers to that of the cooling region is quite small. A great quantity of energy for refrigeration is doomed to waste. In this study, a new cooling strategy for building a non-uniform environment in the heading face was developed. A certain quantity of well-designed tracking air coolers were distributed in the excavation roadway near the heading face. The air cooler tracked the constantly moving workers and blew cold air to them. Economic analysis based on estimation of the cooling load for this cooling strategy was conducted. The airflow in the excavation roadway was numerically simulated to estimate the cooling effect. An average energy saving of approximately 30% could be realized. The thermal environment for the workers whether near the heading face... [more]

An increase in demand for energy natural resources has stimulated the development of gas pipeline networks in Europe, as well as globally. Also, in Poland in recent years there has been a significant increase in natural gas consumption. Therefore, it is necessary to build new pipelines networks using dig and no−dig techniques. Horizontal Directional Drilling is one of the most popular trenchless technologies. The aim of this article is to present a new approach in the design of HDD trajectories in two−dimensional space (2D). A review of the trajectories used so far has been provided, offering calculation algorithms to determine their well path. Then, the original catenary method is proposed, taking into account natural deflection of casing pipes. Applicable formulas and computational algorithms have been given, together with a computational example which enables comparison of the classical design methodology with the new one. According to the authors, due to natural stress distribution... [more]

Solar radiation is the sole energy source for Chinese solar greenhouse agriculture. A favorable light environment is the foundation of a desirable crop growth environment, and it is key in solar greenhouse design. In this study, a mathematical model is established to quantitatively evaluate the solar greenhouse light environment. The model was developed considering the greenhouse shape parameters, materials’ optical properties, and interior solar radiation evolution, including the beam radiation, diffuse radiation, and multi-reflection. The model was validated under different weather conditions, and the results reveal a mean percentage error of 1.67 and 10.30% for clear sunny weather and cloudy weather, respectively, and a determination coefficient of 0.9756. By using this model, the solar radiation allocation in a solar greenhouse was calculated to determine the solar radiation availability for the heat-storage north wall and the entire greenhouse, and the dynamical spatial distributi... [more]

Advanced thermal control technologies have been continuously developed to complement conventional models and algorithms to improve their performance regarding control accuracy and energy efficiency. This study analyses the strengths and weaknesses of simultaneous controls for the amount of air and its temperature by use of on-demand and predictive control strategies responding to two different outdoor conditions. The framework performs the comparative analyses of an on-demand model, which reacts immediately to indoor conditions, and a predictive model, which provides reference signals derived from data learned. Two models are combined to make a comparison of how much more efficient the combined model operates than each model when abnormal situations occur. As a result, when the two models are combined, its efficiency improves from 20.0% to 33.6% for indoor thermal dissatisfaction and from 13.0% to 44.5% for energy use, respectively. This result implies that in addition to creating new... [more]

The effective thermal conductivity (λeff) of sands is a critical parameter required by applications in geothermal energy resources, geo-technique and geo-environment and in science disciplines. However, the availability of the reliable λeff data is not sufficient and predictive models are usually used in practice to estimate λeff. These predictive models may vary in complexity, flexibility, accuracy and applications. There is no universal model that can be applied to all soil types and full water content range. The choice of different models may result in distinctive estimates of λeff. The objectives of this study were to conduct an extensive review of the thermal conductivity models of sands and evaluate their performance with a large dataset consisting of various sand types from dry to saturation. A total of 14 models to predict λeff of sands were evaluated with a large compiled dataset consisting of 1025 measurements on 62 sands from 20 studies. The results show that the models of C... [more]

Multi-fractured horizontal wells (MFHW) is one of the most effective technologies to develop tight gas reservoirs. The gas seepage from tight formations in MFHW can be divided into three stages: early stage with high productivity, transitional stage with declined productivity, and final stage with stable productivity. Considering the characteristics and mechanisms of porous flows in different regions and at different stages, we derive three coupled equations, namely the equations of porous flow from matrix to fracture, from fracture to near wellbore region, and from new wellbore region to wellbore then an unstable productivity prediction model for a MFHW in a tight gas reservoir is well established. Then, the reliability of this new model, which considers the multi-fracture interference, is verified using a commercial simulator (CMG). Finally, using this transient productivity prediction model, the sensitivity of horizontal well’s productivity to several relevant factors is analyzed. T... [more]

Oily brine from the gas and oil industries remains the most difficult wastewater to treat due to its complex chemical composition, which includes aromatic hydrocarbons. Even at low concentrations, the presence of BTX (benzene, toluene, xylenes) can be extremely harmful to aquatic ecosystems. Fixed-bed adsorption columns are recommended for oily water treatment due to their flexibility and easy operation. In this research, pine sawdust modified with polydimethysiloxane (PDMS) and hydrophobic nanosilica was applied as a sorbent in a filtration system. The surface modification of raw fiber allowed to change its morphology and increase the roughness of it. The Yoon−Nelson, Bohart−Adams, Clark, and Belter models were applied to simulate continuous biosorption. The Bohart−Adams model strongly correlated with the experimental data and described the whole dynamic behavior of the column. The effect of feed flow rate (10−50 mL/min) on breakthrough characteristics was determined. Both the breakth... [more]

The rapid development of automobile industry in China did improve people’s quality of life. However, it has also damaged the ecological environment. The emission of a large amount of automobiles is one of the serious air pollution sources. In recent years, the shortage of petrochemical energy, the rapid rise of harmful particles in the air (e.g., PM2.5 and PM10), and the increasing worse atmospheric environment are becoming obstacles to China’s sustainable development. Battery electric vehicles (BEVs) are recognized as an ideal alternative to conventional cars. This study aims to explore the factors that can promote consumers’ adoption of BEVs and to construct domains of these factors. Firstly, an open web questionnaire and semi-structured interviews were conducted to widely collect factors that promote consumers’ purchase of BEVs. Then, questionnaire survey and exploratory factor analysis were used to construct domains of promoting consumers’ purchasing willingness. A total of six fac... [more]

A greenhouse gas (GHG) emission reduction obligation system has been implemented in the Swedish road transport sector to promote the use of biofuels. For transportation fuel suppliers to fulfil this obligation, the volume of biofuel required decreases with decreasing life cycle GHG emission for the biofuel, linking lower GHG emission to higher economic value. The aim of this study was to investigate how the economic competitiveness of a Swedish emerging lignocellulosic-based ethanol production system would be influenced by the reduction obligation. The life cycle GHG emission for sawdust-based ethanol was calculated by applying the method advocated in the EU Renewable Energy Directive (RED II). The saving in GHG emissions, compared with fossil liquid transportation fuels, was 93% for a potential commercial production system in southern Sweden. This, in turn, will increase the competitiveness of sawdust-based ethanol compared to the mainly crop-based ethanol currently used in the Swedis... [more]

Solar thermal power is nowadays one of the trendiest topics in the construction industry, and it represents a valuable energy source of heating that reduces energy consumption. As solar panels produce heating during the day and consumers demand calefaction during the whole day, we use standby tanks (for domestic hot water) and buffer tanks (for heating) for storage. The latest developments improved the efficiency and useful life while reducing the volume of tanks. So, the presented research work deals with analyzing the solar thermal power in a family house. This work presents a method to create a decision support system to compare solar energy systems in houses from economical, technical, availability, and environmental concerns. The weights of the criteria selected considering the analytical hierarchy process are computed. Parameters required for energy production calculations (location, temperature, etc.) and energy consumption (inhabitants, outdoor temperature, etc.) are summarized... [more]

Climate change, other environmental impacts due to increased energy use worldwide, and the exhaustion of energy resources are some of the major challenges facing today’s society. Considering this, this paper assesses the importance of biomass-based heating and hot-water systems in the achievement of more sustainable buildings. Using a simplified calculation method, we jointly analyzed the potential operational cost savings and reduction of CO2 emissions that would be achieved when the traditional energy model, based on the use of fossil fuels, is replaced by biomass-based heating systems. Evidence stems from a case study in public buildings in the province of Pontevedra, in the northwest of Spain. The results of this research not only show a huge impact on CO2 emission reduction just by adapting the kind of fuel use, but also considerable annual cost reduction without compromising activity development and workers’ comfort. Thus, the findings obtained should encourage governments to sup... [more]

The subsea tree is one of the critical pieces of equipment in the subsea production system, and its installation is related to the safe production of offshore oil and gas. Due to the differences in the form of the structures, the speed of entering the water, the marine environment, and other factors, the process of the structure entering the water is exceedingly complicated. During the engineering installation, the most dangerous phase involves the structure passing through the splash zone. Based on the theory of the movement of the subsea tree passing through the splash zone, Lingshui 17-2 subsea tree installation was analyzed with the marine engineering software OrcaFlex, and a sensitivity analysis of the lowering of the subsea tree was performed. During the splash zone phase, the wave height had the highest impact on the subsea tree, affecting the horizontal offset and cable load, which may lead to the oil tree capsizing and cable breakage. Furthermore, the velocity only affected th... [more]

Furfural is a platform molecule obtained from hemicellulose. Among the products that can be produced from furfural, furfuryl alcohol is one of the most extensively studied. It is synthesized at an industrial scale in the presence of CuCr catalyst, but this process suffers from an environmental negative impact. Here, we demonstrate that a non-noble metal catalyst (Co/SiO2) was active (100% conversion of furfural) and selective (100% selectivity to furfuryl alcohol) in the hydrogenation of furfural to furfuryl alcohol at 150 °C under 20 bar of hydrogen. This catalyst was recyclable up to 3 cycles, and then the activity decreased. Thus, a comparison between batch and continuous flow reactors shows that changing the reactor type helps to increase the stability of the catalyst and the space-time yield. This study shows that using a continuous flow reactor can be a solution to the catalyst suffering from a lack of stability in the batch process.

Climate change will require societal-scale infrastructural changes. Balancing priorities for water, energy, and climate will demand that approaches to water and energy management deviate from historical practice. Infrastructure designed to mitigate environmental harm, particularly related to climate change, is likely to become increasingly prevalent. Understanding the implications of such infrastructure for environmental quality is thus of interest. Environmental life cycle assessment (LCA) is a common sustainability assessment tool that aims to quantify the total, multicriteria environmental impact caused by a functional unit. Notably, however, LCA quantifies impacts in the form of environmental “costs” of delivering the functional unit. In the case of mitigation infrastructures, LCA results can be confusing because they are generally reported as the harmful impacts of performing mitigation rather than as net impacts that incorporate benefits of successful mitigation. This paper argue... [more]

Scientific research plays an important role in the achievement of a sustainable society. However, grasping the trends in sustainability research is difficult because studies are not devised and conducted in a top-down manner with Sustainable Development Goals (SDGs). To understand the bottom-up research activities, we analyzed over 300,000 publications concerned with sustainability by using citation network analysis and natural language processing. The results suggest that sustainability science’s diverse and dynamic changes have been occurring over the last few years; several new topics, such as nanocellulose and global health, have begun to attract widespread scientific attention. We further examined the relationship between sustainability research subjects and SDGs and found significant correspondence between the two. Moreover, we extracted SDG topics that were discussed following a convergent approach in academic studies, such as “inclusive society” and “early childhood development... [more]

Our paper focuses on the renewable energy and EU 2020 target for energy efficiency in the Czech Republic and Slovakia. We study the reduction of greenhouse gas (GHG) emissions in these two EU Member States through the prism of the Europe 2020 strategy and the 3 × 20 climate and energy package and economic growth (represented by the Gross Domestic Product (GDP) that allows to measure the national dynamics and provide cross-country comparisons) without attributing specific attention to issues such as the electrification of transport or heating, and thence leaving them outside the scope of this paper. Both Czech Republic and Slovakia are two post-Communist countries that still face the consequences of economic transformation and struggle with the optimal management of natural resources. Both countries encountered profound system transformation after 1989 that are apparent in all three measures of sustainable development used in our study. We show that it is unlikely that the planned incre... [more]

The aim of this article is to provide an overview of greenhouse gas emission reduction potentials for 2030 based on the assessment of detailed sectoral studies. The overview updates a previous assessment that dates back more than ten years. We find a total emission reduction potential of 30−36 GtCO2e compared to a current-policies baseline of 61 GtCO2e. The energy production and conversion sector is responsible for about one third of this potential and the agriculture, buildings, forestry, industry, and transport sectors all contribute substantially to the total potential. The potential for 2030 is enough to bridge the gap towards emissions pathways that are compatible with a maximum global temperature rise of 1.5−2 °C compared to preindustrial levels.

With the continuous implementation of a plan for reconstruction of “Beautiful Countryside” in China, the rural environment and appearance of rural houses have been significantly improved. However, those houses in cold areas of China have great trouble with indoor temperature and heating-related energy consumption. After investigating the current situation of the layout, building envelope, indoor temperature, and energy consumption of the rural houses renovated by the plan of “Beautiful Countryside” in Shandong Province, this paper puts forward the improvement measures of raising indoor temperature and reducing energy consumption. On this basis, a typical rural house was selected, and DesignBuilder was utilized to simulate the effects before and after the application of different renovation measures for this house. The results show that the main way to raise indoor temperature and reduce energy consumption is to improve the thermal insulation performance of the building envelope, includ... [more]

The lower cost of sensors is making possible the acquisition of big data sets in several applications and research areas. Indoor air quality and commuter exposure to pollutants are some of these areas, which can have impacts on our livelihood. The main objective of this exploratory research was to assemble portable equipment along with a prototype, one low-cost and easy to replicate in any location worldwide. We answer how CO2, noise and energy expenditure compare in different transportation modes with indoor environments (metro, bus and car). It was intended to be carried by a subject on all commutes. The low-cost equipment assembled has the ability to measure ambient CO2, noise levels, heart rate and geographic coordinates. The field campaign was conducted on an urban commuting route, in Lisbon city, between Rossio (downtown of Lisbon city) and Campo Grande (near FCUL campus). It took place during 3 weeks in school break and 3 weeks in the school period to grasp some differences betw... [more]

The origin of the organic-rich shale in the Upper Ordovician Wufeng Formation and Lower Silurian Longmaxi Formation is complex and controversial. This paper reports the geochemical data of Wufeng-Longmaxi Formations in the Upper Yangtze region to restore the paleoenvironment and explore the accumulation mechanism of organic matter. The total organic carbon (TOC) content of the Wufeng Formation was relatively high, with an average of 2.86%. The Lower Longmaxi Formation showed the highest TOC content, with an average of 3.99%, and the upper part was a continuously low value with an average of 1.22%. The paleoproductivity proxies (Babio, Cu/Al, Ni/Al, Siexcess) showed that in the Katian and Rhuddanian-Aeronian Stages, the Upper Yangtze Sea had high primary productivity, indicating that organic matter accumulation was more affected by terrigenous influx and redox conditions. Al, Zr, and Zr/Al indicated that terrigenous influx was relatively high in the Kaitian-Hirnantian Stages, it was at... [more]

The enhancement of the financial sector significantly drives a nation’s economy and thereby increase energy intensity. Considering this situation, the current study aims to examine the link between globalization and financial advancements with the energy intensity of the top 5 ASEAN (Association of Southeast Asian Nations) economies. The development structure of the ASEAN region is considered significant for having stable growth. The authors used the annual data from 1990 to 2018 for five of the largest ASEAN economies: Singapore, Malaysia, Thailand, Indonesia, and the Philippines. The present study used novel methodology, the Adaptive Neuro-Fuzzy Inference System (ANFIS), to examine the nonlinear behaviour among globalization, financial development, and energy intensity in the top 5 ASEAN countries. The study results using ANFIS confirm that globalization and financial development are positively correlated and have a significant impact on the energy intensity level in the top ASEAN co... [more]

Given the environmental footprints of the conventional agriculture, it is imperative to test and validate alternative production systems, with lower environmental impacts to mitigate and adapt our production systems. In this study, we identified six production systems, four in Italy and two in Denmark, to assess the environmental footprint for comparison among the production systems and additionally with conventional production systems. SimaPro 8.4 software was used to carry out the life cycle impact assessment. Among other indicators, three significantly important indicators, namely global warming potential, acidification, and eutrophication, were used as the proxy for life cycle impact assessment. In Italy, the production systems compared were silvopastoral, organic, traditional, and conventional olive production systems, whereas in Denmark, combined food and energy production system was compared with the conventional wheat production system. Among the six production systems, convent... [more]

The objective of this study is to develop (1) a pose-categorization model that classifies the poses of an occupant based on their image in an indoor space and (2) an activity-decision algorithm that identifies the activity being performed by the occupant. For developing an automated intelligent model, a deep neural network is adopted. The model considers the coordinates of the joints of the occupant in the image as input data and returns the pose of the occupant. Datasets composed of indoor images of home and office environments are used for training and testing the model. The training and testing accuracies of the optimized model were 100% for both the home and office environments. A representative activity of an occupant for a certain period has to be decided to control an indoor environment for comfort. The activity-decision algorithm employs a frequency-based method to determine the representative activity type for real-time occupant poses using the pose-categorization model. This... [more]

The industrial sector dominates the global energy consumption and carbon emissions in end use sectors, and it faces challenges in emission reductions to reach the Paris Agreement goals. This paper analyzes and quantifies the relationship between industrialization, energy systems, and carbon emissions. Firstly, it forecasts the global and regional industrialization trends under Representative Concentration Pathway (RCP) and Shared Socioeconomic Pathway2 (SSP2) scenarios. Then, it projects the global and regional energy consumption that aligns with the industrialization trend, and optimizes the global energy supply system using the Model for Energy Supply Strategy Alternatives and their General Environmental Impact (MESSAGE) model for the industrial sector. Moreover, it develops an expanded Kaya identity to comprehensively investigate the drivers of industrial carbon emissions. In addition, it employs a Logarithmic Mean Divisia Index (LMDI) approach to track the historical contributions... [more]