Breaking through the limit of conventional compression and combustion, wave rotor and trapped vortex combustors are able to improve the thermal efficiency of gas turbines. Detailed two-dimensional numerical simulations based on Ansys Fluent were performed to study the flow and combustion characteristics of the wave rotor−trapped vortex combustor system. The calculated pressure characteristics agree with the experimental results giving a relative error for average pressure of 0.189% at Port 2 and of 0.672% at Port 4. The flow stratification characteristics and the periodic fluctuations were found to benefit the zonal organized combustion in the trapped vortex combustor. For the six cases of different rotor speeds, as the rotor speed increased, the oxygen mass fraction at the combustor inlet rose and then fell. The proportion of exhaust gas recirculation fell at first and then rose, and the combustion mode became unstable with the dominant frequencies of the fluctuations increasing.

Enhancing carbon emission mitigation and carbon utilization have become necessary for the world to respond to climate change caused by the increase of greenhouse gas concentrations. As a result, carbon capture, utilization, and storage (CCUS) technologies have attracted considerable attention worldwide, especially in China, which plans to achieve a carbon peak before 2030 and carbon neutrality before 2060. This paper proposed six priorities for China, the current world’s largest carbon emitter, to achieve its dual carbon strategy in the green energy transition process. We analyzed and summarized the challenges and potentialities of conventional carbon utilization (CU), carbon capture utilization (CCU), and CCUS. Based on the current development trend, carbon dioxide capture, circular utilization, and storage (CCCUS) technology that integrates carbon circular utilization and partial sequestration, with large-scale underground energy storage were proposed, namely biomethanation. Technica... [more]

Since the discovery of Photovoltaic (PV) effect, numerous ways of utilizing the energy that can be generated by the free everlasting solar radiation using solar panels were put forward by many researchers. However, the major disadvantage of solar panel to date is its low efficiency, which is affected by the panel temperature, cell type, panel orientation, irradiance level, etc. Though there are certain multi-junction solar panels that offer higher efficiencies, their application is very minimal due to high manufacturing cost. With the growing demand for the reduction of carbon footprint, there is a need to use and manufacture these panels in the most effective way to harness the maximum power and increase their efficiency. Another major concern is the availability of land/space for the installation of these panels. Several authors have focused on discussing the different technologies that have evolved in the manufacturing of the PV cells along with their architectures. However, there e... [more]

Solar energy presents the greatest potential by which to produce heat energy with reduced carbon emissions for power generation. To increase its harvesting and conversion, it is necessary to understand fundamental concepts and develop new materials. Although many processes can obtain selective absorbing surfaces (SAS) for application in solar energy exploitation, including electroplating methods, those processes have not sufficiently investigated the substrate’s treatment impact. The present work investigates 304 stainless steel (SS304) substrates treatment influence on the film’s (coatings) optical properties of SAS based on CrO3 electroplating. For this purpose, three main steps featured in the methodology: substrates treatment, coatings deposition, and physical-chemical characterization. The former was performed by detergent cleaning (DC), acid treatment (AT), and electropolishing (EP). Then, coatings were electroplated towards chromium deposition on the substrates with different de... [more]

Due to the proposal of China’s carbon neutrality target, the traditional fossil energy industry continues to decline, and the proportion of new energy continues to increase. New energy power systems have high requirements for peak shaving and energy storage, but China’s current energy storage facilities are seriously insufficient in number and scale. The unique features of abandoned mines offer considerable potential for the construction of large-scale pumped storage power stations. Several countries have reported the conversion of abandoned mines to pumped storage plants, and a pilot project for the conversion of an underground reservoir group has been formalized in China. A feasibility study that considered the natural conditions, mine conditions, safety conditions, and economic benefits revealed that the construction of pumped storage power stations using abandoned mines could ameliorate several economic, ecological, and social problems, including resource utilization, ecological re... [more]

Remaining useful life (RUL) prediction of batteries is important for the health management and safety evaluation of lithium-ion batteries. Because lithium-ion batteries have capacity recovery and noise interference during actual use, direct use of measured capacity data to predict their RUL generalization ability is not efficient. Aimed at the above problems, this paper proposes an integrated life prediction method for lithium-ion batteries by combining improved variational mode decomposition (VMD) with a long short-term memory network (LSTM) and Gaussian process regression algorithm (GPR). First, the VMD algorithm decomposed the measured capacity dataset of the lithium-ion battery into a residual component and capacity regeneration component, in which the penalty factor α and mode number K in the VMD algorithm were optimized by the whale optimization algorithm (WOA). Second, the LSTM and GPR models were established to predict the residual component and capacity regeneration components... [more]

Particulate matter (PM) pollution from coal combustion is a leading contributor to the influence of atmospheric visibility, photochemical smog, and even global climate. A drop tube furnace was employed to explore the effects of temperature and chemical speciation of mineral elements on PM formation during the combustion of Zhundong coal. Chemical fractionation analysis (CFA), X-ray fluorescence (XRF), and inductively coupled plasma-atomic emission spectrometry (ICP-AES) were used to investigate the chemical and physical characteristics of the solid samples. It can be indicated that the combustion of similarly sized coal particles yielded more PM10 when the combustion temperature was increased from 1000 to 1400 °C. Zhundong coal is fractionated with deionized water, ammonium acetate, and hydrochloric acid, and pulverized coal, after fractionation, is burned to study the influence of mineral elements with different occurrence forms, such as water-soluble mineral elements, exchangeable io... [more]

An emerging problem associated with the increased global demand for electric vehicles (EVs) is the post-use of lithium-ion batteries installed in them. Discarded batteries maintain 70−80% of their performance; thus, they are highly valuable recycling resources. Accordingly, technologies that complement the intermittency of renewable energy by integrating discarded EV batteries into battery energy storage systems (BESSs) are receiving attention. Here, the economic feasibility of a residential solar photovoltaic (PV) + reused BESS (RBESS) integrated system in three emerging countries (Philippines, Indonesia, and Vietnam) was analyzed by comparing its performance with that of diesel power generation and central grid-supplied power. The proposed system had a higher economic feasibility than diesel power generation (55.9% lower LCOE) but a lower economic feasibility than the central grid-supplied power (282.7% higher LCOE) in all three countries. Additionally, we conducted a sensitivity ana... [more]

This work proposed an optimal design of PV-system-based water-pumped energy storage for both electricity and water supply. A case study was considered in a rural community in Cameroon. The parameters of the assessment of the system were reliability, represented in the present work by the system supply deficiency (SSD), and economic accessibility, represented by the levelized cost of energy (LCOE). The obtained results showed that for 0% SSD, the optimal configuration of the system was composed of 438 PV modules of 235 W, an immersed solar motor pump of 35 kW, a hydroelectric turbine of 51.7 kW, an upper reservoir of 2307.1 m3, an inverter of 25.27 kW, and a total dynamic head of 88 m. The corresponding LCOE to this configuration is 0.224 USD/kWh. The economic accessibility of the designed system was evaluated by comparison with a PV-system-based battery energy storage. The optimal design configuration of the studied PV-system-based battery energy storage was a PV generator (120 PV modu... [more]

Integrated optimization of well placement and hydraulic fracture parameters in naturally fractured shale gas reservoirs is of significance to enhance unconventional hydrocarbon energy resources in the oil and gas industry. However, the optimization task usually presents intensive computation-cost due to numerous high-fidelity model simulations, particularly for field-scale application. We present an efficient multi-objective optimization framework supported by a novel hierarchical surrogate-assisted evolutionary algorithm and multi-fidelity modeling technology. In the proposed framework, both the net present value (NPV) and cumulative gas production (CGP) are regarded as the bi-objective functions that need to be optimized. The hierarchical surrogate-assisted evolutionary algorithm employs a novel multi-fidelity particle-swarm optimization of a global−local hybridization searching strategy where the low-fidelity surrogate model is capable of exploring the populations globally, while th... [more]

Power transformers are still equipment of primary importance within power grids. The recent paradigm changes registered in the field of energy require the interconnection of electrical grids of much larger areas, even up to the level of an entire continent. In this context, knowing the state of the electrical equipment and that of the power transformers is an essential aspect to ensure safe operation conditions. The present work is related to the vulnerability of the oil−paper insulation systems of power transformers to different aging factors and their quick degradation under certain conditions. In this regard, the study proposed in this paper considers the measurement of DC resistivity on mineral oil samples contaminated with small amounts of accelerated aging oil under the action of high-strength electric field and partial discharges. In the absence of standardized procedures for accelerated electrical aging of mineral oil, an original method presented and discussed in previous arti... [more]

The main objective of this work was to investigate the potential of hydrogen and fuel cells replacing diesel and internal combustion engines in the ultraclass haul trucks deployed in the mining sector. Performance, range, durability, and cost are the main criteria considered for comparing the two fuels and engine options. Fuel cell system (FCS) performance is characterized in terms of heat rejection, efficiency, and fuel consumption for a hybrid platform equivalent to a 3500 hp diesel engine operating on a representative open pit mining duty cycle. A hybrid platform was chosen because the heat rejection, with a constrained radiator frontal area, limits the maximum fuel cell-rated power by about 50% compared to that of the diesel truck. The hybrid powertrain was 81−88% more efficient than the diesel powertrain on the truck duty cycle. A liquid hydrogen storage system is required for an equal range or time between refilling, but the packaging remains a challenge. Fuel cell and battery du... [more]

Within the past decade, since impediments in nonrenewable fuel sources and the contamination they cause, utilizing green energies, such as those that are sun-oriented, in tandem with electric vehicles, is a developing slant. Coordinating electric vehicle (EV) charging stations with sun-powered boards (PV) reduces the burden of EV charging on the control framework. This paper presents a state-of-the-art literature review on remote control transmission frameworks for charging the batteries of electric vehicles utilizing sun-based boards as a source of power generation. The goal of this research is to advance knowledge in the wireless power transfer (WPT) framework and explore more about solar-powered electric vehicle charging stations. To do this, a variety of solar-powered electric vehicle charging station types are thoroughly studied. Following a study of many framework elements, the types of WPT components are explored in a different section. Within the wireless power transmission fra... [more]

A significant development of the photovoltaic market in the European Union has been observed recently. This is mainly due to the adopted climate policy and the development of photovoltaic technology, resulting in increased availability for consumers at lower prices. In the long run, increased installed PV capacity is associated with an increased amount of photovoltaic waste generated at the end of life. Since this waste belongs to the group of WEEE (waste electrical and electronic equipment) waste, it is subjected to high recovery levels. Existing installations for the highly efficient recycling of PV panels are just proofs of concept. However, the situation will change in the near future, and it will be necessary to implement a full-scale waste management system dedicated to PV waste. The paper estimates mass streams of photovoltaic waste generated by 2050 in individual EU countries. Consequently, the characteristics of the European market of waste PV panels are considered together wi... [more]

Supplying shipping vessels with electricity at the ports can improve the air quality of the ports, reduce the greenhouse gas emissions from the shipping industry, contribute to the economic growth, and increase the political dependency of the countries by reducing the dependence on conventional fossil fuels. Several countries promote supplying the vessels when they are docking at ports from renewable energy systems by establishing dedicated funding mechanisms to remove the obstacles facing the shore power systems. In this context, this paper presents a new modular power electronic converter for shore power systems at shipping ports, which can perform three functions. Firstly, it will harvest the energy from a renewable energy source, such as hydroelectric and solar photovoltaic (PV) sources and ensure maximum energy extraction. Secondly, it will control the power flow from these sources to the battery storage. Finally, it will control the power flow from the battery to the vessels and/... [more]

Researchers at many different institutions around the world study voltage and current waveform distortions in power networks using a variety of techniques. Due to the uncontrolled growing number of nonlinear devices supplied by electrical energy, more severe supraharmonic pollution has been observed. A bibliometric analysis of the topic development between 2013 and 2022 is presented in the paper. Using the selected search tools, a comparative review of articles published in the last three years was conducted. It organizes the existing knowledge about supraharmonic pollution generated by nonlinear devices and identifies current research challenges associated with the spread of these disturbances in electrical networks. The most frequently discussed topics by researchers are those that deal with the level of emissions generated by supraharmonic sources and their effects on components of the power system. The second most prominent research direction is the detection, measurement, analysis... [more]

Inverters with Quasi-Z-Source Networks (QZSN) provide DC-DC boosting and DC-AC conversion in a single stage. It offers reduced cost, complexity, and volume compared with the classical two-stage conversion system, which is composed of a boost converter followed by a Voltage-Source-Inverter (VSI). Further, QZSI provides superior conversion characteristics for single-stage grid-connected photovoltaic transformerless systems. However, the absence of galvanic isolation in these systems makes it possible to allow leakage current through these systems’ parasitic capacitances due to the high-frequency Common-Mode Voltage (CMV) generated by the Pulse Width Modulation (PWM) nature of the inverter output voltages. As a result of this current, critical safety issues may arise with PV systems. Many PWM techniques have been presented in recent years for QZSIs. This paper is intended to provide a comprehensive analysis and review study of the characteristics of most of these PWM techniques in terms o... [more]

Homogeneous charge compression ignition is considered a promising solution to face the increasing regulations imposed by the legislator in the transport sector, thanks to pollutant and CO2 emissions reduction. In this work, a quasi-dimensional multi-zone HCCI model integrated with 1D commercial software is developed and validated. It is based on the control mass Lagrangian approach and computes the mixture chemistry evolution through offline tabulation of chemical kinetics (tabulated kinetic of ignition). Thus, the simulation can predict mixture auto-ignition with reduced computational effort and high accuracy. Multi-zone schematization mimics the typical thermal stratification of HCCI engines, controlling the combustion evolution. The model is coupled to sub-models for pollutant emissions estimation. Initially, the tabulated chemistry approach is validated against a chemical kinetics solver applied to a constant-volume homogeneous reactor, considering various fuel blends. The model is... [more]

Data sets of internal resistances and open-circuit voltage of a particular battery are needed in ANSYS Fluent program to predict the heat generation accurately. However, one set of available data, called Chen’s original, does not cover all types and shapes of batteries. Therefore, this research was intended to study the effects of shapes and polarization chemistries on heat generation in Li-ion batteries. Two kinds of material chemistries (nickel manganese cobalt oxide, NMC, and lithium iron phosphate, LFP) and three forms (cylindrical, pouch, and prismatic) were studied and validated with the experiment. Internal resistance was unique to each cell battery. Differences in shapes affected the magnitude of internal resistance, affecting the amount of heat generation. Pouch and prismatic cells had lower internal resistance than cylindrical cells. This may be the result of the forming pattern, in which the anode, cathode, and separator are rolled up, making electrons difficult to move. In... [more]

Well interference has drawn great attention in the development of shale gas reservoirs. In the W shale gas reservoir, well interference increased from 27% to 63% between 2016 and 2019, but the gas production recovery of parent wells was only about 40% between 2018 and 2019. Therefore, the mechanism and influencing factor of well interference degree were analyzed in this study. A numerical model of the W shale gas reservoir was developed for history matching, and the mechanisms of well interference and production recovery were analyzed. Sensitivity analysis about the effect of different parameters on well interference was carried out. Furthermore, the feasibility and effectiveness of gas injection pressure boosting to prevent interference were demonstrated. The results show that the main causes of inter-well interference are: the reservoir energy of the parent well before hydraulic fractures of the child well, well spacing, the fracture connection, etc. The fracture could open under hig... [more]

This paper proposes a high-frequency isolated current-fed dual active bridge bidirectional DC−DC series resonant converter with an inductive filter for energy storage applications, and a steady-state analysis of the converter is carried out. The performance of the proposed converter has been compared with a voltage-fed converter with a capacitive output filter. The proposed converter topology is operated in continuous conduction mode with zero circulation current (ZCC), less current stress and high efficiency. The conditions required for soft switching are determined, and it is found that the converter operates with soft switching of all switches for a wide variation in load and input voltage without loss of duty cycle. Current-fed converters are suitable for low-voltage renewable energy applications because of their inherent boosting capability. An inductive output filter is chosen to make the output current ideal for fast charging and high-power-density battery storage applications.... [more]

The high-voltage battery is a crucial element for EV traction systems. It is the primary energy source that must be regularly recharged to reach the autonomy declared by the manufacturer. Therefore, an EV charging system is required to ensure the battery charging process. This review thoroughly investigates the available EV charging technologies and the most popular batteries for EV applications. The contributions of this work can be summarized as follows: the classification and topologies of electric vehicle chargers are examined, an overview of the current EV charging standards is provided, the state-of-the-art of EV charging couplers is discussed, and the most widely used batteries in EV applications are reviewed.

The formation and the blockage of plant equipment such as heat exchangers by heavy hydrocarbon (HHC) solids is an inherent risk in cryogenic natural gas processing. The accuracy of the gas mixture’s compositional characterization significantly impacts the reliability of solid formaiton temperature predictions. Recently, we showed that complete characterization of the mixture is necessary to obtain accurate predictions of the melting temperature, as current methods based on pseudocomponent characterizations of HHCs are inadequate. Here, we present an improved method of characterizing HHCs that represents each pseudocomponent up to C14+ by a paraffinic, isoparaffinic, naphthenic and aromatic (PINA) composition and allocates an associated defined component to represent these sub-fractions. This new, extended PINA-based characterization of HHC pseudocomponents is derived from 46 different pipeline natural gas samples, and the method is validated against three representative gas samples tha... [more]

Frequency, tie-line power, and the terminal voltages of synchronized generators must all be kept within prescribed limits to ensure the stability of an interconnected power grid through combined automatic generation control (AGC) and automatic voltage regulator (AVR) loops. Thermal power plants, electric vehicles, and renewable energy sources—including solar and wind, geothermal, and solar thermal power plants—form the two-area integrated power system in present research. A new cascade controller named the cascaded proportional integral derivative (PID) and fractional-order PID (CPID-FOPID) controller is proposed for the first time, whose performance is compared with the PID and FOPID controller. The results show that the proposed cascade controller outperforms PID and FOPID in delivering superior dynamic characteristics, including short settling times and low oscillation amplitudes. A new metaheuristic algorithm named the coot algorithm was applied to optimize the parameters of these... [more]

The EU’s hydrogen strategy consists of studying the potential for renewable hydrogen to help decarbonize the EU in a cost-effective way. Today, hydrogen accounts for less than 2% of Europe’s energy consumption. It is primarily used to produce chemical products. However, 96% of this hydrogen production is through natural gas, leading to significant amounts of CO2 emissions. In this paper, we investigated PV electrolysis H2 gas (noted H2(g)) production for mapping this resource at Europe’s scale. The Cordex/Copernicus RCPs scenarios allow for evaluating the impact of climate changes on the H2-produced mass and the equivalent energy, according to both extreme RCPs scenarios. New linear regressions are investigated to study the great dependence in H2(g) produced masses (kg·yr−1) and equivalent energies (MWh·yr−1) for European countries. Computational scenarios are investigated from a reference year (2005) to the end of the century (2100) by steps of 5 years. According to RCPs 2.6 (favorabl... [more]