E-scooters as a new form of mobility are gaining more and more popularity. This popularity results from the flexibility of this mode of transport, but above all from the positive impact on the natural environment through the much higher energy efficiency of an e-scooter compared to a motor vehicle (according to the literature the rate is 2 km per kWh equivalent for a motor vehicle and the range is 90−100 km per kWh in the case of an e-scooter). This paper introduces a discussion on the future development of an energy-efficient electric scooter sharing system based on stakeholder analysis methods. The implementation of the e-scooter sharing system involves linking several areas of human activity, including social activity. This, in turn, relates to the interactions and building of relationships with entities, particularly those influencing the provision of services and their effects. The large number of entities and the complexity of the relations between them make it a challenge both t... [more]

With the development of space exploration, high-power and high-voltage power systems are essential for future spacecraft applications. Because of the effects of space radiation such as single event burnout (SEB), the rated voltage of power devices in converters for a spacecraft power system is limited to a level much lower than that for traditional ground applications. Thus, multi-level DC/DC converters are good choices for high-voltage applications in spacecraft. In this paper, a fault-tolerant strategy is proposed for a three-level flying capacitor DC/DC converter to increase the reliability with minimal cost. There is no extra hardware needed for the proposed strategy; the fault tolerance of the converter is only achieved by changing the software control strategy. A stage analysis of the proposed strategy is provided in detail for different fault locations and ratios between the input and output voltage. Finally, a simulation model and prototype are built to verify the effectiveness... [more]

The article presents the results of the analysis of parameters describing electricity consumption in individual phases of the production cycle on a poultry farm. One full broiler rearing cycle on the farm was analyzed. Electrical parameters were tested during the broiler rearing process using a power quality analyzer with a measurement interval of 1 min. During the tests, the analyzer recorded the active and reactive power, phase and line voltage, power factor, and frequency. On the basis of collected data, original indicators describing electricity consumption per chicken wkA, wkQ, and per unit area wiA, wiQ were determined. The regression curves of active and reactive power consumption in particular stages of the cycle were also determined, and the minimum and maximum values of active and reactive power consumption were determined. The accomplished research can be used in planning electricity demand in energy-self-sufficient areas. The presented original indicators can be used to det... [more]

This study aims to institutionalize an evaluation methodology to assess water-source heat pumps (WSHPs) when designing a zero-energy building. Thus, regions where zero-energy buildings were designed were subdivided into 66 sub-regions, thereby standardizing the temperatures on the source side of WSHPs using river water and pipeline water. Based on these data, ground-source and water-source heat pump system-based simulation (new and renewable energy self-sufficiency rate compared to building energy consumption) values were derived for cases whose condition (region or heat source) was different among the buildings certified as zero-energy buildings. The application of the standard meteorological data and reference hydrothermal data to the ECO2 program and outcome evaluation led to the following findings: in all cases (reference: Seoul), ground-source heat pumps (GSHPs) showed a higher self-sufficiency rate than WSHPs (ground source > pipeline water > river water). The self-sufficiency ra... [more]

Cold climate regions have great potential for wind power generation. The available wind energy in these regions is about 10% higher than in other regions due to higher wind speeds and increased air density. However, these regions usually have favorable icing conditions that lead to ice accumulation on the wind turbine blades, which in turn increases the weight of the blades and disrupts local airflow, resulting in a reduction in wind turbine performance. Considering this problem, plasma actuators have been proposed as devices for simultaneous flow control and deicing. These devices transfer momentum to the local airflow, improving the aerodynamic performances of the turbine blades while producing significant thermal effects that can be used to prevent ice formation. Considering the potential application of plasma actuators for simultaneous flow control and deicing, it is very important to investigate the thermal effects induced by these devices. However, due to the significant electrom... [more]

Over the years, high voltage transmission of large energy blocks over long distances has widely developed from the Line Commutated Converter (LCC) technology. However, the continuous expansion of the AC network and the increase in renewable energy penetration leads to the weakening of Electric Power Systems (EPS), causing operational problems for the LCC-HVDC. This paper evaluates the degree of contribution of the VSC-HVDC on the LCC-HVDC dynamic performance when the infeed is in a hybrid multi-infeed HVDC system. Through a steady-state mathematical framework, the new concept of Hybrid Power Voltage Interaction Factor (hPVIF) is proposed to assess the transient stability improvement of LCC. Additionally, this article introduces two key contributions from hPVIF: the complementary Improved Commutation Failure Immunity Index (iCFII), as a measure of the effective short circuit enhancement, as well as the apparent line length, which emulates the line lengths adjusting the power dispatch in... [more]

The persistent fight against global environmental threats and energy catastrophe is currently a major concern for the economic development of bioenergy across the entire country. Hence, traditional fuel-based reserves are overburdened to cope with the rapid energy crisis, necessitating an urgent need for an innovative carbon-neutral green-energy resource. In order to address these critical bottlenecks, microalgae with incredible metabolic versatility have paved the way for a pivotal attention towards sustainable biofuel production. However, due to high operational costs and low lipid productivity, the microalgae-based biofuel resource is still in its infancy. As a result, this problem can be overcome by incorporating engineered microalgal strains which can pave the way for significant lipid augmentation for biofuel production. Thus, our current review depicts an in-depth understanding of a multi-omics approach to microalgae, the broad scope of self-sustaining microalgae cultivation, li... [more]

Wave energy converters (WECs) have enormous potential in providing clean renewable energy with high levels of predictability [...]

Increasing energy usage efficiency requires enhanced heat energy recuperation between process streams in the industry and civic sector with waste heat utilization. The condensation of different vapours is the process encountered in many industrial applications. Increasing the heat recuperation in this process is possible with efficient heat transfer equipment, among which a Plate Heat Exchanger (PHE) is at the leading position. A number of research works have been conducted in recent years concerning construction development and heat transfer enhancement in conditions of limited pressure drop to increase PHE performance in condensation processes. The results of studies on heat transfer and pressure drop in the two-phase condensing flow inside channels of PHE with different geometries of corrugations are discussed. In many implementations, the total pressure drop allowable for gaseous streams in heat exchangers is relatively small. The structure of two-phase flow in PHE channels of comp... [more]

To restrain the environmental impact of modern SI engines, igniters must guarantee stable combustions with low cycle-to-cycle variability in extreme operating conditions (high EGR, ultra-lean), via high energy release in the combustion chamber. The direct measurement of this energy is not trivial and requires a controlled environment. Luminosity detection is a non-intrusive diagnostic technique to indirectly measure the thermal energy released by the discharge on optically accessible apparatus. This work compares energy and luminosity produced by a plasma igniter in a constant volume vessel at realistic working conditions (ignition at 8 bar and air as a medium). A calibration factor can be defined to describe the thermal energy behavior as a function of the discharge luminosity and to give an assessment of such approach for its use in optically accessible engine. This study shows that thermal energy and luminosity are influenced by the gas type and related by a linear relationship for... [more]

The treatment and disposal of sewage sludge is one of the most important and critical problems of wastewater treatment plants. 8.7 million tonnes of dry matter of sewage sludge were produced annually in the European Union in the year 2020. Due to the fact that sewage sludge contains a large number of substances that are not beneficial for human health, the conditions for sludge management will be significantly tightened in the EU countries. One option for sludge liquidation is the production of biofuel in a form of granules or pellets from sewage sludge enriched by waste celluloses. The achieved results show that the resulting quality of such alternative biofuel is fully comparable to conventional fossil fuels. The economic analysis is based on the simulation of cash flows associated with the implementation of the project over the lifetime and the calculation of levelised cost (LCOE). Results shows (under the current economic situation) that solar dryer technology ensures the lowest LC... [more]

As it has an export-oriented economy, Taiwan urgently needs to keep up with the growing trends toward carbon taxation. However, making the institution of a carbon tax a reality in Taiwan has proven to be difficult. Since 1998, Taiwan has explored the possibility of putting a tax on carbon many times. Specifically, three main windows of opportunity emerged to adopt a carbon tax during this period; however, all of them failed. This study mainly explores why these three opportunities failed, what structural factors hindered them, and how those structural factors formed path dependence and locked the entire society back onto the existing development track. Firstly, Taiwan’s high-carbon industrial structure has established the rapid growth of energy-intensive industries since the end of the 1990s and has created an economy with high energy consumption and pollution levels. Secondly, this analysis showed that through the combination of government bureaucracy, industry, and the China National... [more]

Oil shale is a crucial unconventional energy source to supplement conventional oil and gas. The oil shale in the Maoming Basin of China has excellent resource potential. In this study, through systematic geochemical testing, the industrial quality and geochemical characteristics of oil shale are revealed, and the hydrocarbon generation potential of oil shale, the parent rock type, and the tectonic setting of the source area are discussed. It is comprehensively assessed that Maoming oil shale has a medium-oil yield (avg. 6.71%) with high ash content (avg. 76.1%), a high calorific value (avg. 7.16 M J/kg), and ultra-low sulfur (avg. 0.54%). The mineralogical compositions primarily consist of clay minerals and quartz, and barely pyrite. Maoming oil shale is in an immature evolution stage, with high TOC and I-II1 kerogen type, and could be considered an excellent hydrocarbon source rock. The chemical index of alteration (CIA), the index of chemical variability (ICV), and the Th/U ratio ind... [more]

Because wind power is connected to the grid on a large scale, frequency fluctuation in the power grid, which is defined as a system safety risk to the power grid, occurs from time to time. According to the grid code rules of China, wind turbines are required to be equipped with primary frequency modulation or inertia response control capability, which are used to support the safe and stable operation of the power grid. During the traditional frequency modulation process of the wind turbine, power limiting operation or pitch angle reservation is generally adopted to ensure that the reserved energy can be released at any time to support the frequency change in the power grid. However, the frequency support method leads to a large loss of power generation, and does not consider the coordination between mechanical load characteristics control and primary frequency modulation. In this paper, a mechanical load optimization control strategy for a wind turbine during the primary frequency modu... [more]

Forecasting energy consumption in Saudi Arabia for the period from 2020 until 2030 is investigated using a two-part composite model. The first part is the frontier, and the second part is the autoregressive integrated moving average (ARIMA) model that helps avoid the large disparity in predictions in previous studies, which is what this research seeks to achieve. The sample of the study has a size of 30 observations, which are the actual consumption values in the period from 1990 to 2019. The philosophy of this installation is to reuse the residuals to extract the remaining values. Therefore, it becomes white noise and the extracted values are added to increase prediction accuracy. The residuals were calculated and the ARIMA (0, 1, 0) model with a constant was developed both of the residual sum of squares and the root means square errors, which were compared in both cases. The results demonstrate that prediction accuracy using complex models is better than prediction accuracy using sin... [more]

The study deals with the analysis of data from a selected tourism facility and the implementation of a solar system and a rainwater system, which are an alternative to commonly used energy sources. The objective is to evaluate the potential savings from the use of the solar system for water heating and the rainwater system for purposes other than potable use with respect to local conditions of sunlight and rainwater variability. The facility holds 257 beds allocated in 124 rooms on 5 floors. The result of the contribution is an economic evaluation of the efficiency of investments in the proposed systems and the resulting recommendations in the field of energy flows in the selected facility. Appropriate formulas including the consumption of hot water, the amount of energy needed to heat water, the cost of the consumed energy necessary for heating and the average annual rainfall in the location, water consumption for clearly identified purposes of alternation with rainwater, the initial... [more]

This study proposes a data-driven methodology for modeling power and hydrogen generation of a sustainable energy converter. The wave and hydrogen production at different wave heights and wind speeds are predicted. Furthermore, this research emphasizes and encourages the possibility of extracting hydrogen from ocean waves. By using the extracted data from the FLOW-3D software simulation and the experimental data from the special test in the ocean, the comparison analysis of two data-driven learning methods is conducted. The results show that the amount of hydrogen production is proportional to the amount of generated electrical power. The reliability of the proposed renewable energy converter is further discussed as a sustainable smart grid application.

Distributed electric power production by small-scale customers is increasing continuously. Photovoltaic production is a popular method of producing self-energy for customers. Additionally, power systems require more flexibility when weather-dependent renewable energy production increases. Small-scale customers can increase the self-consumption of self-produced energy by using batteries or a demand response operation. However, batteries require high investment, and demand response operations induce a loss of comfort. Customers who heat their buildings using electric heaters are a good target for demand response operations because their heating can be controlled with limited changes in the indoor temperature. The demand response potential of a building can be defined by simply using customer load profiles and knowledge of the outdoor temperature. Any other information is not required in the proposed novel method. A tolerable variation in indoor temperature corresponds to considerably sma... [more]

Palm oil is, from an economic, environmental, and social point of view, a vegetable oil with great potential and the state of Pará-Brazil is Brazil’s great producer. In addition, soap phase residue or palm oil neutralization sludge (PONS), a byproduct of the neutralization step of the chemical refinement of palm oil, is produced, posing a huge problem for waste disposal and management in the production process of refined palm oil (RPO). In this context, this work aims to systematically investigate the economic analysis of the thermal−catalytic process of crude palm oil (CPO) and palm oil neutralization sludge (PONS). The thermocatalytic processes of CPO and PONS carried out at pilot scale and their economic feasibility were analyzed. The yields of biofuels produced by fractional distillation were also presented. The physicochemical properties of CPO and PONS, as well as those of organic liquid products obtained by the thermal−catalytic process of CPO and PONS were taken into account in... [more]

This study investigates the possibility of applying a large-scale solar updraft tower power plant in India with local ground conditions as an environmentally friendly and economically viable energy source. A reference model Solar Updraft Tower Power Plant (SUTPP) is constructed to examine the influence of the most prominent plant dimensional parameters, including collector radius (RCollector), tower height (HTower), and tower radius (RTower) with dimensional limits and intervals on the power output of the SUTPP. Udat, Rajasthan, India, is used as a reference location for meteorological conditions to evaluate SUTPP power output equations for a ranging power output, with position coordinates of 27°35′ and 72°43′. Multiple simulations for the objective function are carried out, and the outcomes are compared to the optimized dimensions of each set of plants. The model examines the effect of variation in ambient, plant geometry, and material conditions on power output and analyzes efficienc... [more]

The six-pole radial−axial hybrid magnetic bearing (RAHMB) has the advantages of small space and low power consumption, making it suitable for flywheel batteries. The bearing capacity and the volume are the main specifications of magnetic bearings that should be considered comprehensively. In this work, the six-pole RAHMB was used in a horizontal flywheel battery. As the axial bearing capacity is relatively smaller than the radial bearing capacity, a design method with independent radial and axial bearing capacity is proposed, and the parameters are optimized to minimize the volume. The mathematical model of six-pole RAHMB was derived from the equivalent magnetic circuit method. The relationships between bearing capacity, biased flux density, saturation flux density and the section area of magnetic poles were analyzed. The basic principle of the design method with independent radial and axial bearing capacity is to determine which five of the variables are preferred. According to the de... [more]

The energy autonomy of UAVs is an important direction in the field of aerospace. Long-endurance aerial vehicles allow for continuous flight; however, to meet the guidelines, the power supply system has to be able to harvest energy from outside. Solar cells allow the production of electricity during the day when the sun shines on their surface. Depending on the location, time, weather, and other external factors, the energy produced by PV panels will change. In order to calculate as accurately as possible the energy obtained by solar cells, we developed a simulation model that took into account all of the external restrictions and the UAV’s limits during flight. The conducted analysis made it possible to obtain information for the specific input data on whether the UAV is able to fly for 24 h in a specific flight scenario. The UAV powered by solar cells developed by us and the performed aviation missions have shown that the UAV is capable of continuous flight without the need to land.

The most significant geo-energy sources in the world today continue to be oil, gas, and geothermal reservoirs. To increase oil and gas reserves and production, new theories are constantly being developed in the laboratory and new technologies are being applied in the oilfield. This Special Issue compiles recent research focusing on cutting-edge ideas and technology in oil, gas, and geothermal reservoirs, covering the fields of well drilling, cementing, hydraulic fracturing, improved oil recovery, conformance control, and geothermal energy development.

The constant development of civilization increases environmental pollution as a result of industrial activity and transport. Consequently, human activity in this area is restricted by regulations governing the permissible emission of harmful substance components into the environment. These include substances emitted by combustion engines, the use of which remains high in many industries. Consequently, research is being conducted to reduce the emissions of harmful exhaust components from existing and newly manufactured internal combustion engines. This research presents a used semi-truck engine, in which an innovative Compressed Natural Gas (CNG) supply system was applied. Using this fuel supply installation allows a mass exchange of the base diesel fuel to natural gas of up to 90%. The study evaluated the effect of the diesel/CNG exchange ratio for different engine operating conditions (engine load, speed) on the concentration of toxic components, such as CO, NO, NO2, NOX, as a sum of... [more]

Given the importance of renewable energy sources in distribution systems, this article addresses the problem of locating and determining the capacity of these sources, namely, wind turbines and solar panels. To solve this optimization problem, a new algorithm based on the behavior of salp is used. The objective functions include reducing losses, improving voltage profiles, and reducing the costs of renewable energy sources. In this method, the allocation of renewable resources is considered for different load models in distribution systems and different load levels using smart meters. Due to the fact that these objective functions are multi-objective, the fuzzy decision-making method is used to select the optimal solution from the set of Pareto solutions. The considered objective functions lead to loss reduction, voltage profile improvement, and RES cost reduction (A allocating RES resources optimally without resource limitations; B: allocating RES resources optimally with resource lim... [more]