The task of site selection for electric vehicle charging stations (EVCS) is hugely important from the perspective of harmonious and sustainable development. However, flaws and inadequacies in the currently used multi-criteria decision making methods could result in inaccurate and irrational decision results. First of all, the uncertainty of the information cannot be described integrally in the evaluation of the EVCS site selection. Secondly, rigorous consideration of the mutual influence between the various criteria is lacking, which is mainly evidenced in two aspects: one is ignoring the correlation, and the other is the unconscionable measurements. Last but not least, the ranking method adopted in previous studies is not very appropriate for evaluating the EVCS site selection problem. As a result of the above analysis, a Preference Ranking Organization Method for Enrichment Evaluations (PROMETHEE) method-based decision system combined with the cloud model is proposed in this paper fo... [more]

For magnetic-coupled resonator wireless power transmission (WPT) systems, higher power transfer efficiency can be achieved over a greater range in comparison to inductive-coupled WPT systems. However, as the distance between the two near-field resonators varies, the coupling between them changes. The change in coupling would in turn vary the power transfer efficiency. Generally, to maintain high efficiency for varying distances, either frequency tuning or impedance matching are employed. Frequency tuning may not limit the tunable frequency within the Industrial Scientific Medical (ISM) band, and the impedance matching network involves bulky systems. Therefore, to maintain higher transfer efficiency over a wide range of distances, we propose a multiple coil switching wireless power transmission system. The proposed system includes several loop coils with different sizes. Based on the variation of the distance between the transmitter and receiver side, the power is switched to one of the... [more]

Direct numerical simulations (DNS) of Mach = 2.9 supersonic turbulent boundary layers with spanwise wall oscillation (SWO) are conducted to investigate the turbulent heat transport mechanism and its relation with the turbulent momentum transport. The turbulent coherent structures are suppressed by SWO and the drag is reduced. Although the velocity and temperature statistics are disturbed by SWO differently, the turbulence transports of momentum and heat are simultaneously suppressed. The Reynolds analogy and the strong Reynolds analogy are also preserved in all the controlled flows, proving the consistent mechanisms of momentum transport and heat transport in the turbulent boundary layer with SWO. Despite the extra dissipation and heat induced by SWO, a net wall heat flux reduction can be achieved with the proper selected SWO parameters. The consistent mechanism of momentum and heat transports supports the application of turbulent drag reduction technologies to wall heat flux controls... [more]

An automatic forest-stand selection method was developed that integrates the procurement of profitable energy sources within a sustainable energy production system. We tested the method using a forest harvester simulator. We found that site-specific estimates of forest characteristics are important when predicting the potential of an energy-wood stand as a renewable energy source. Further, tree parameters can be combined with automatic stem measurements from a multiple-tree harvester to predict the energy-wood biomass in the stands. The selection process uses data from profitability studies. The selection process also uses environmental criteria to ensure that sufficient soil organic matter is left behind and to protect the soil against erosion. The integrated system of the harvester automatically adapts the system’s models and stand-selection rules to account for various site-specific stand parameters. Predicting the profitable and environmentally acceptable yield of stand biomass has... [more]

To more completely extract useful features from low frequency oscillation (LFO) signals, a time-frequency analysis method using resonance-based sparse signal decomposition (RSSD) and a frequency slice wavelet transform (FSWT) is proposed. FSWT can cut time-frequency areas freely, so that any band component feature can be extracted. It can analyze multiple aspects of the LFO signal, including determination of dominant mode, mode seperation and extraction, and 3D map expression. Combined with the Hilbert transform,the parameters of the LFO mode components can be identified. Furthermore, the noise in the LFO signal could reduce the frequency resolution of FSWT analysis, which may impact the accuracy of oscillation mode identification. Complex signals can be separated by predictable Q-factors using RSSD. The RSSD method can do well in LFO signal denoising. Firstly, the LFO signal is decomposed into a high-resonance component, a low-resonance component and a residual by RSSD. The LFO signal... [more]

Hydraulic turbines exhibit total load rejection during operation because of high fluctuations in the grid parameters. The generator reaches no-load instantly. Consequently, the turbine runner accelerates to high speed, runaway speed, in seconds. Under common conditions, stable runaway is only reached if after a load rejection, the control and protection mechanisms both fail and the guide vanes cannot be closed. The runner life is affected by the high amplitude pressure loading at the runaway speed. A model Francis turbine was used to investigate the consequences at the runaway condition. Measurements and simulations were performed at three operating points. The numerical simulations were performed using standard k-ε, k-ω shear stress transport (SST) and scale-adaptive simulation (SAS) models. A total of 12.8 million hexahedral mesh elements were created in the complete turbine, from the spiral casing inlet to the draft tube outlet. The experimental and numerical analysis showed that th... [more]

In power conversion of photovoltaic (PV) energy, a hard-switching buck converter always generates some disadvantages. For example, serious electromagnetic interference (EMI), high switching losses, and stresses on an active switch (metal-oxide-semiconductor-field-effect-transistor, MOSFET), and high reverse-recovery losses of a freewheeling diode result in low conversion efficiency. To release these disadvantages, a buck converter with soft-switching cells for PV panel applications is proposed. To create zero-voltage-switching (ZVS) features of the active switches, a simple active soft-switching cell with an inductor, a capacitor, and a MOSFET is incorporated into the proposed buck converter. Therefore, the switching losses and stresses of the active switches and EMI can be reduced significantly. To reduce reverse-recovery losses of a freewheeling diode, a simple passive soft-switching cell with a capacitor and two diodes is implemented. To verify the performance and the feasibility of... [more]

With soaring energy demands, the desire to explore alternate and renewable energy resources has become the focal point of various active research fronts. Therefore, the scientific community is revisiting the notion to tap wind resources in more rigorous and novel ways. In this study, a two-dimensional computational investigation of the vertical axis wind turbine (VAWT) with omni-direction-guide-vane (ODGV) is proposed to determine the effects of this guide vane. In addition, the mesh and time step (dt) size dependency test, as well as the effect of the different turbulence models on results accuracy are investigated. Eight different shape ratios (R) of the omni-direction-guide-vane were also examined in this study. Further, the CFD model is validated by comparing the numerical results with the experimental data. Validation results show a good agreement in terms of shape and trend in CFD simulation. Based on these results, all the shape ratios, except two ratios including 0.3 and 0.4 at... [more]

Partial discharge (PD) detection is essential to the operation of high-voltage systems. In this context, we investigate the basic characteristics of light emission during PDs in SF₆ gas from the perspective of insulation diagnosis. A synchronous system is constructed using three optical photoelectric instruments with separate wavelength responses in the ultraviolet (UV, 189⁻352 nm), visible (VIS, 381⁻675 nm), and near-infrared (NIR, 737⁻920 nm) spectral ranges and a wide-band PD current pulse detector with a response of 1 pC. The results indicate that light emission depends upon the type of insulation defect and discharge energy. An increase in PD charge gives rise to more components in the spectral range from UV to VIS, and the presence of an insulator surface in discharges yields a more complex VIS-to-NIR spectrum. The phase-resolved partial discharge pattern (PRPD) of UV light pulses can reasonably reflect the electroluminescence process in the presence of the insulator surface and... [more]

This paper presents the design and implementation of a communication and control infrastructure for smart grid operation. The proposed infrastructure enhances the reliability of the measurements and control network. The advantages of utilizing the data-centric over message-centric communication approach are discussed in the context of smart grid applications. The data distribution service (DDS) is used to implement a data-centric common data bus for the smart grid. This common data bus improves the communication reliability, enabling distributed control and smart load management. These enhancements are achieved by avoiding a single point of failure while enabling peer-to-peer communication and an automatic discovery feature for dynamic participating nodes. The infrastructure and ideas presented in this paper were implemented and tested on the smart grid testbed. A toolbox and application programing interface for the testbed infrastructure are developed in order to facilitate interopera... [more]

Partial shading is an unavoidable condition which significantly reduces the efficiency and stability of a photovoltaic (PV) system. When partial shading occurs the system has multiple-peak output power characteristics. In order to track the global maximum power point (GMPP) within an appropriate period a reliable technique is required. Conventional techniques such as hill climbing and perturbation and observation (P&O) are inadequate in tracking the GMPP subject to this condition resulting in a dramatic reduction in the efficiency of the PV system. Recent artificial intelligence methods have been proposed, however they have a higher computational cost, slower processing time and increased oscillations which results in further instability at the output of the PV system. This paper proposes a fast and efficient technique based on Radial Movement Optimization (RMO) for detecting the GMPP under partial shading conditions. The paper begins with a brief description of the behavior of PV... [more]

As global competition increases, technological capability must be evaluated objectively as one of the most important factors for predominance in technological competition and to ensure sustainable business excellence. Most existing capability evaluation models utilize either quantitative methods, such as patent analysis, or qualitative methods, such as expert panels. Accordingly, they may be in danger of reflecting only fragmentary aspects of technological capabilities, and produce inconsistent results when different models are used. To solve these problems, this paper proposes a comprehensive framework for evaluating technological capabilities in energy companies by considering the complex properties of technological knowledge. For this purpose, we first explored various factors affecting technological capabilities and divided the factors into three categories: individual, organizational, and technology competitiveness. Second, we identified appropriate evaluation items for each categ... [more]

Wind power generation reduces our reliance on fossil fuels and can thus reduce environmental pollution. However, rapid wind power development has caused various issues related to power grid restructuring. A high proportion of the generating capacity of northeast China is based on combined heat and power (CHP), whose inflexible response to the peak regulation of power grids hinders the ability to accommodate wind power; thus, wind power curtailment is prevalent. Electric boilers can directly consume the excess wind power to supply heat during low load periods and thus mitigate the heat supply stress of CHP units. Therefore, electric boilers improve the power grid’s ability to accommodate additional wind power. From a regional power grid perspective, this paper discussed the feasibility of such a strategy for increasing the ability to accommodate wind power during the heat supply season. This paper analysed the optimum electric boiler capacity configuration of a regional power grid based... [more]

The purpose of this study is to reduce the unnecessary plug loads used by computers, monitors, and computer peripheral devices, all of which account for more than 95% of the entire plug loads of an office building. To this end, an occupant-based plug-in device control (OBC-P) software was developed. The OBC-P software collects real-time information about the presence or absence of occupants who are connected to the access point through the Wifi and controls the power of monitors or computers, while a standby power off device controls computer peripheral devices. To measure the plug load saving of the occupant-based plug-in device control, an experiment was conducted, targeting 10 occupants of three research labs of the graduate school, for two weeks. The experiment results showed that it could save the plug loads of monitors and computer peripheral devices by 15% in the Awake mode, and by 26% in the Sleep mode.

This paper describes the complete integration of a fuzzy control of multiple evaporator systems with the IEEE 802.15.4 standard, in which we study several important aspects for this kind of system, like a detailed analysis of the end-to-end real-time flows over wireless sensor and actuator networks (WSAN), a real-time kernel with an earliest deadline first (EDF) scheduler, periodic and aperiodic tasking models for the nodes, lightweight and flexible compensation-based control algorithms for WSAN that exhibit packet dropouts, an event-triggered sampling scheme and design methodologies. We address the control problem of the multi-evaporators with the presence of uncertainties, which was tackled through a wireless fuzzy control approach, showing the advantages of this concept where it can easily perform the optimization for a set of multiple evaporators controlled by the same smart controller, which should have an intelligent and flexible architecture based on multi-agent systems (MAS) th... [more]

In hybrid electric vehicles with power-split configurations, the engine can be decoupled from the wheel and operated with improved fuel economy, while the entire efficiency of the powertrain is affected by the circular electric power flow. Two planetary gear (2-PG) sets with adding brakes/clutches, namely a type of four shaft elelctric continuously variable transmission (ECVT) can provide multi-mode operation for the powertrain and extend the efficient area. First, a conventional 2-PG AT (Automatic Transmission) architecture is investigated. By analyzing and comparing the connection and operating modes based on the kinematic relationship and lever analogy, a feasible four-shaft ECVT architecture with two brakes and two simplified versions are picked. To make a trade-off between fuel economy and configuration complexity, an instantaneous optimal control strategy based on the equivalent consumption minimization strategy (ECMS) concept is then developed and employed as the unified optimiz... [more]

Numerical simulation is very useful for understanding the hydraulic fracturing mechanism. In this paper, we simulate the hydraulic fracturing using the distinct element approach, to investigate the effect of some critical parameters on hydraulic fracturing characteristics. The breakdown pressure obtained by the distinct element approach is consistent with the analytical solution. This indicates that the distinct element approach is feasible on modeling the hydraulic fracturing. We independently examine the influence of in-situ stress ratio, injection rate and fluid viscosity on hydraulic fracturing. We further emphasize the relationship between these three factors and their contributions to the hydraulic fracturing. With the increase of stress ratio, the fracture aperture increases almost linearly; with the increase of injection rate and fluid viscosity, the fracture aperture and breakdown pressure increase obviously. A low value of product of injection rate and fluid viscosity (i.e.,... [more]

In this paper, a novel voltage equalizer is developed for series battery strings based on the two-phase switched capacitor technique. Different from the conventional voltage equalizers which are developed by switched-mode power converters, bulky magnetic components and complex monitoring and control system are avoided in the proposed system. Just a pair of complementary pulse signals with constant switching frequency and fixed duty ratio are required to control all of switches employed in the proposed voltage equalizer, and charge transfers from the higher voltage battery cells to lower voltage ones automatically. The circuit configuration and operation principle are provided in this paper. The model of the proposed voltage equalizer is also derived. Comparison with other works indicates that the proposed method is superior to the conventional switched-capacitor (SC) voltage equalizer for the high stack of series battery strings. Experimental results demonstrate that the proposed volta... [more]

The increasing global demand for palm oil and its products has led to a significant growth in palm plantations and palm oil production. Unfortunately, these bring serious environmental problems, largely because of the large amounts of waste material produced, including palm kernel shell (PKS). In this study, we used computational fluid dynamics (CFD) to investigate the PKS co-firing of a 300 MWe pulverized coal-fired power plant in terms of thermal behavior of the plant and the CO₂, CO, O₂, NOx, and SOx produced. Five different PKS mass fractions were evaluated: 0%, 10%, 15%, 25%, and 50%. The results suggest that PKS co-firing is favorable in terms of both thermal behavior and exhaust gas emissions. A PKS mass fraction of 25% showed the best combustion characteristics in terms of temperature and the production of CO₂, CO, and SOx. However, relatively large amounts of thermal NOx were produced by high temperature oxidation. Considering all these factors, PKS mass fractions of 10%⁻15% e... [more]

The paper deals with the impact of subsequent strokes on the backflashover rate (BFR) of HV overhead transmission lines (OHLs), assessed by means of an ATP-EMTP Monte Carlo procedure. The application to a typical 150 kV Italian OHL is discussed, simulating several tower grounding system arrangements. Subsequent strokes parameters are added to the statistical simulation variables: peak current, front time, time-to-half value, lightning polarity, line insulation withstand, lightning location and phase angle of the power frequency voltage. The input data are fed to an ATP-EMTP complete circuit model of the OHL, including line insulation, lightning representation and tower grounding system, the latter simulated by a pi-circuit model able to simulate the effects due to propagation and soil ionization, at modest computational costs. Numerical results evidence a non-negligible BFR increase (in relative terms) due to subsequent strokes: for spatially concentrated grounding systems the BFR incr... [more]

Under harsh weather conditions, closed transplant production systems (CTPS) are currently used to produce high quality transplants under artificial lighting. More than 70% of the electric energy consumed in the CTPS is for lighting. This article presents a simulation study to examine the possibility of using an alternative closed solar house, with radiation filtering roof, for transplant production in hot sunny regions to replace the artificial lighting in the CTPS with sunlight. The sidewalls of the house were insulated as in the CTPS and the roof was transparent, and made from polycarbonate hollow-channeled structure. There was a liquid radiation filter (LRF) (1.5% CuSO₄⁻water solution) flowing in a closed loop through the roof channels to absorb the solar heat load (i.e., the near infra-red radiation, NIR: 700⁻2500 nm) and transmit the photosynthetically active radiation (PAR: 400⁻700 nm) for plant growth. The LRF inlet temperature was assumed to be 25 °C to prevent vapor condensati... [more]

This paper proposes the active damping control strategy for position sensorless operation of an interior permanent magnet (IPM) motor. The proposed method is applied to both the current controller and the position estimator to control damping characteristics of the IPM drive system. By actively increasing the damping characteristics of the system with the proposed method, the current control and the position estimation loops become immune to parameter variation of the stator resistance which may degrade the accuracy of the position estimator. To analyze the accuracy of the position estimator with and without the proposed method, a small-signal analysis is carried out for low speed operation where the effect of the parameter variation is relatively large due to a low signal-to-noise ratio (SNR). Additionally, an open-loop voltage to angular velocity transfer function including the electrical and the mechanical parameters is investigated. Since no hardware modifications are necessary, th... [more]

This paper proposes a novel dual-consequent-pole Vernier memory machine (DCP-VMM) featuring alternatively arranged NdFeB and low coercive-force (LCF) magnet poles on the rotating and stationary sides, respectively. Due to the presence of LCF magnets that can be repetitively magnetized or demagnetized via a simple current pulse, the extra-high torque density at low-speed, and excellent high-efficient high-speed flux-weakening performance can be simultaneously realized. The configuration and operating principle, as well as the design considerations of the proposed machine are introduced, respectively. The finite element method (FEM) coupled with a nonlinear analytical hysteresis model for LCF magnets is employed to investigate the electromagnetic performance of the machine, which verifies the effectiveness of machine design and the feasibility as a competent candidate for automotive applications.

Central and Northern Argentinean regions possess a high potential for the generation of solar energy. The realization of this potential is an alternative to alleviate the strong dependence on imports of fossil energy and to reduce the CO₂ emissions of the country. However, the adoption of photovoltaics (PV) is still in an incipient state. It is undermined by a context of heavily subsidized electricity prices, high equipment and installation costs and a lack of information, training and experience in handling PV technology. This paper presents a techno-economical assessment of the application of the recently enacted net-metering law for promoting renewable energies (RE) in the Province of Salta (Northwest Argentina) for the case of PV. The assessment shows under which conditions and for which types of consumers it is profitable to adopt PV in the context of the law. This analysis is supported by a participatory planning approach as a study of stakeholders’ attitudes towards RE, intentio... [more]

The interest of calculating the effects of thermal bridges in buildings energy consumption is growing, due to recent energy saving regulations applied in different countries. The widespread use of insulating materials to reduce energy requirements of buildings, often employed for intermediate insulation of the building envelope, makes thermal bridges a crucial point in the energy analysis of building envelopes. Furthermore, heat losses through thermal bridges often lead to building pathologies due to moisture condensation. Therefore, thermal bridges need to be correctly characterized in the building design stage in order to reduce heat losses and avoid materials degradation. The authors numerically simulate, by using finite elements, the steady-state and dynamic three-dimensional (3D) heat and vapor transport in inhomogeneous thermal bridges and building envelopes. The aim of the present work is to show the importance of taking into account the presence of inhomogeneities (i.e., metal... [more]