The global tidal energy resource for electricity generation is small, and converting tidal kinetic energy to electricity is expensive compared to solar-photovoltaic or land-based wind turbine generators. However, as the renewable energy content in electricity supplies grows, the need to stabilise these supplies increases. This paper describes tidal energy’s potential to reduce intermittency and variability in electricity supplied from solar and wind power farms while lowering the capital expenditure needed to improve dispatchability. The paper provides a model and hypothetical case studies to demonstrate how sharing energy storage between tidal stream power generators and wind or solar power generators can mitigate the level, frequency, and duration of power loss from wind or solar PV farms. The improvements in dispatchability use tidal energy’s innate regularity and take account of tidal asymmetry and extended duration low-velocity neap tides. The case studies are based on a national... [more]

By considering the weight penalty of batteries on payload and total vehicle weight, this paper shows that almost all forms of land-based transport may be served by battery electric vehicles (BEV) with acceptable cost and driving range. Only long-distance road freight is unsuitable for battery electrification. The paper models the future Indian electricity grid supplied entirely by low-carbon forms of generation to quantify the additional solar PV power required to supply energy for transport. Hydrogen produced by water electrolysis for use as a fuel for road freight provides an inter-seasonal energy store that accommodates variations in renewable energy supply. The advantages and disadvantages are considered of midday electric vehicle charging vs. overnight charging considering the temporal variations in supply of renewable energy and demand for transport services. There appears to be little to choose between these two options in terms of total system costs. The result is an energy sce... [more]

The electrical power sector plays an important role in the economic growth and development of every country around the world. Total global demand for electric energy is growing both in developed and developing economies. The commitment to the decarbonization of economies, which would mean replacing fossil fuels with renewable energy sources (RES) as well as the electrification of transport and heating as a means to tackle global warming and dangerous climate change, would lead to a surge in electricity consumption worldwide. Hence, it appears reasonable that the electric power sector should embed the principles of sustainable development into its functioning and operation. In addition, events such as the recent European gas crisis that have emerged as a result of the massive deployment of renewables need to be studied and prevented. This review aims at assessing the role of the renewable energy in the sustainable development of the electrical power sector, focusing on the energy provid... [more]

Europe stated the ambitious target of becoming carbon neutral by 2050 to combat climate change and meet the requirements imposed by the Paris Agreement, and renewable energy has proved to be a promising solution for the decarbonization of many sectors. Nonetheless, their aleatory nature leads to grid unbalances due to the difference between supply and demand. Storage solutions are needed, and electrofuels become a key factor in this context: they are fuels produced from electricity, which leads to carbon-neutral fuels if it originates from renewable sources. These can constitute a key solution to store the surplus energy and to decarbonize the so-called hard-to-abate sectors. Electrofuel production technologies have not yet been fully developed, and, in this context, extensive study of the state-of-the-art of existing projects can be very useful for researchers and developers. This work researches the European projects funded by the Horizon 2020 Programme regarding electrofuel producti... [more]

Among numerous functions performed by the battery management system (BMS), online estimation of the state of health (SOH) is an essential and challenging task to be accomplished periodically. In electric vehicle (EV) applications, accurate SOH estimation minimizes failure risk and improves reliability by predicting battery health conditions. The challenge of accurate estimation of SOH is based on the uncertain dynamic operating condition of the EVs and the complex nonlinear electrochemical characteristics exhibited by the lithium-ion battery. This paper presents an artificial neural network (ANN) classifier experimentally validated for the SOH estimation of lithium-ion batteries. The ANN-based classifier model is trained experimentally at room temperature under dynamic variable load conditions. Based on SOH characterization, the training is done using features such as the relative values of voltage, state of charge (SOC), state of energy (SOE) across a buffer, and the instantaneous sta... [more]

This paper studies the architectural implications, in terms of size and space requirements, of battery technologies in a built environment using renewable energy and energy storage technologies. These aspects will be of particular interest as the world transitions to a low carbon future. This paper is the first to focus on the physical size of storage systems required to provide particular storage characteristics. The research used a quantitative case study methodology and focused on the investigation of nine battery technologies based on potential technology and energy consumption scenarios in 2030. Different residential building scales at a local distribution scale are explored considering sub-daily autonomy periods. Four case studies in a 2030 scenario are presented. For each case study, the nominal capacity, spatial requirements and costs are assessed for each technology. A schematic characterisation of the technologies was derived considering their suitability across these aspects... [more]

This study proposes a novel dual-PCM configuration with outstanding solidification response in a horizontal shell-and-tube energy storage system. To demonstrate that the proposed PCM configuration is superior in its thermal responses, results from a range of numerical simulations are presented and compared between different configurations of dual-PCM. As the melting/solidus point is a crucial factor for the solidification rate, dual PCMs are chosen such that the average of their melting point is equal to the melting point of the single-PCM in the reference case. Additionally, equal-area sectors are considered for all cases to ensure the same quantities of PCMs are compared. The temporal liquid fraction and temperature contours reveal that solidification is delayed in the upper half of the system due to strong natural convection motions. Therefore, a dual-PCM configuration is offered to improve the solidification rate in this region and accelerate the full solidification process. Result... [more]

Hydrogen is becoming an increasingly important energy carrier in sector integration for fuel cell transportation, heat and electricity. Underground salt caverns are one of the most promising ways to store the hydrogen obtained from water electrolysis using power generation from renewable energy sources (RES). At the same time, the production of hydrogen can be used to avoid energy curtailments during times of low electricity demand or low prices. The stored hydrogen can also be used during times of high energy demand for power generation, e.g., with fuel cells, to cover the fluctuations and shortages caused by low RES generation. This article presents an overview of the techniques that were used and proposed for using excess energy from RES for hydrogen production from water and its storage techniques, especially in underground salt caverns, for the aforementioned purpose, and its feasibility. This paper compares and summarizes the competing technologies based on the current state-of-t... [more]

This paper analyzes the results of a trial operation of a battery-based buffer station supporting a selected section of trolleybus power supply systems in Pilsen, Czech Republic. The buffer station aims to prevent the catenary from excessive voltage drops in a part of the route that is most remote from the traction substation. Compensation of voltage drops is carried out by continuously measuring the catenary voltage and injecting the current into the catenary if the voltage decreases below a preset value. The effectiveness of such a solution was evaluated by the analysis of numerous experimental recordings, both from the buffer station itself and from trolleybuses in operation. Further on, based on the recordings, a utilized battery capacity was estimated and a control method for decreasing the required capacity was proposed. The optimal capacity analysis, supplemented with an evaluation of required output current rating, was used to define the best storage technology for the consider... [more]

Power distribution networks at the distribution level are becoming more complex in their behavior and more heavily stressed due to the growth of decentralized energy sources. Demand response (DR) programs can increase the level of flexibility on the demand side by discriminating the consumption patterns of end-users from their typical profiles in response to market signals. The exploitation of artificial intelligence (AI) methods in demand response applications has attracted increasing interest in recent years. Particle swarm optimization (PSO) is a computational intelligence (CI) method that belongs to the field of AI and is widely used for resource scheduling, mainly due to its relatively low complexity and computational requirements and its ability to identify near-optimal solutions in a reasonable timeframe. The aim of this work is to evaluate different PSO methods in the scheduling and control of different residential energy resources, such as smart appliances, electric vehicles (... [more]

Recently, the integration of optimal battery dispatch and demand response has received much attention in improving DC microgrid operation under uncertainties in the grid-connect condition and distributed generations. However, the majority of prior studies on demand response considered the characteristics of global frequency variable instead of the local voltage for adjusting loads, which has led to obstacles in operating DC microgrids in the context of increasingly rising power electronic loads. Moreover, the consideration of voltage-dependent demand response and optimal battery dispatch has posed challenges for the traditional planning methods, such as stochastic programming, because of nonlinear constraints. Considering these facts, this paper proposes a model predictive control-based integrated voltage-based demand response and batteries’ optimal dispatch operation for minimizing the entire DC microgrid’s operating cost. In the proposed model predictive control approach, the binary... [more]

The need for environmentally benign portable energy storage drives research on organic batteries and catalytic systems. These systems are a promising replacement for commonly used energy storage devices that rely on limited resources such as lithium and rare earth metals. The redox-active TEMPO (2,2,6,6-tetramethylpiperidin-1-oxyl-4-yl) fragment is a popular component of organic systems, as its benefits include remarkable electrochemical performance and decent physical properties. TEMPO is also known to be an efficient catalyst for alcohol oxidation, oxygen reduction, and various complex organic reactions. It can be attached to various aliphatic and conductive polymers to form high-loading catalysis systems. The performance and efficiency of TEMPO-containing materials strongly depend on the molecular structure, and thus rational design of such compounds is vital for successful implementation. We discuss synthetic approaches for producing electroactive polymers based on conductive and n... [more]

In this study, the possibility of sector coupling with biological Power-to-Methane to support and stabilize the energy transition of the three major sectors of electricity, heat, and gas was addressed. For this purpose, the energy cell simulation methodology and the Calliope tool were utilized for energy system optimization. This combination provides detailed insights into the existing dependencies of consumers and fossil and renewable energy suppliers on a local scale. In this context, Power-to-Methane represents an efficient technology for quickly and effectively exploiting unused electricity potential for various sectors and consumers. It was found that, even in regions with low wind levels, this surplus electricity potential already exists and depends on various influencing factors in very different ways. The solar influence on these potentials was considered in connection with gas-fired cogeneration plants for district heating. It was found that the current heat demand for distric... [more]

An economic analysis of the implementation of the power-to-gas (PtG) system between 2030 and 2055 is presented at a large scale. The capacity of the PtG system is adapted to two scenarios in Spain (Bailera and Lisbona 2018), corresponding to growing scenarios of 1.73 and 1.36%/y of its electricity market. The total power capacity of the PtG system has been fixed to 12.7 and 3.84 GW, respectively, at the end of 2055. The levelized cost of storage (LCOS) of the implementation of PtG has been evaluated. Assuming uncertainties in the current cost projections for CAPEX and OPEX, LCOS estimations are between 136 and 686 EUR/MWh with a payback time of 16 years in the best scenario for a reference electricity purchase of 100 EUR/MWh and a CO2 penalty of 100 EUR/ton. A sensitivity analysis and the viability dependence versus energy purchase and CO2 penalty certificates is shown. This work sheds some light for the comparison of PtG implementation costs in comparison with other storage options, s... [more]

Traditional power grids are mainly based on centralized power generation and subsequent distribution. The increasing penetration of distributed renewable energy sources and the growing number of electrical loads is creating difficulties in balancing supply and demand and threatens the secure and efficient operation of power grids. At the same time, households hold an increasing amount of flexibility, which can be exploited by demand-side management to decrease customer cost and support grid operation. Compared to the collection of individual flexibilities, aggregation reduces optimization complexity, protects households’ privacy, and lowers the communication effort. In mathematical terms, each flexibility is modeled by a set of power profiles, and the aggregated flexibility is modeled by the Minkowski sum of individual flexibilities. As the exact Minkowski sum calculation is generally computationally prohibitive, various approximations can be found in the literature. The main contribut... [more]

As the world is keen on cleaner and sustainable energy, hydrogen energy has the potential to be part of the green energy transition to replace fossil fuels and mitigate climate change. However, hydrogen energy storage is a difficult task since physical storage in the form of compressed gas under high pressure is associated with safety issues. Another form of hydrogen storage is material-based storage, which is the safest way to store hydrogen energy in a particulate matter, known as metal hydrides. Metal hydrides can store hydrogen at room temperature and use less volume to store the same amount of hydrogen compared to classical gas tanks. The challenges with the metal hydrides reactor are their slow charging process and the requirement of proper thermal management during the charging process. In this study, a metal hydride reactor model is developed in COMSOL Multiphysics, and the associated heat transfer simulations are performed. The main objective of this research is to optimize th... [more]

Flexible supercapacitors are highly demanding due to their wearability, washability, lightweight property and rollability. In this paper, a comprehensive review on flexible supercapacitors based on conductive polymers such as polypyrrole (PPy), polyaniline (PANI) and poly(3,4-ethylenedioxtthiophne)-polystyrene sulfonate (PEDOT:PSS). Methods of enhancing the conductivity of PEDOT:PSS polymer using various composites and chemical solutions have been reviewed in detail. Furthermore, supercapacitors based on carbonized banana peels and methods of activation have been discussed in point. This review covers the up-to-date progress achieved in conductive polymer-based materials for supercapacitor electrodes. The effect of various composites with PEDOT:PSS have been discussed. The review result indicated that flexible, stretchable, lightweight, washable, and disposable wearable electronics based on banana peel and conductive polymers are highly demanding.

Vehicle-to-grid (V2G) has been identified as a key technology to help reduce carbon emissions from the transport and energy sectors. However, the benefits of this technology are best achieved when multiple variables are considered in the process of charging and discharging an electric vehicle. These variables include vehicle behaviour, building energy demand, renewable energy generation, and grid carbon intensity. It is expected that the transition to electric mobility will add pressure to the energy grid. Using the batteries of electric vehicles as energy storage to send energy back to the grid during high-demand, carbon-intensive periods will help to reduce the impact of introducing electric vehicles and minimise carbon emissions of the system. In this paper, the authors present a method and propose a V2G control scheme integrating one year of historical vehicle and energy datasets, aiming towards carbon emissions reduction through increased local consumption of renewable energy, off... [more]

Energy storage for medium- to large-scale applications is an important aspect of balancing demand and supply cycles. Hydropower generation coupled with pumped hydro storage is an old but effective supply/demand buffer that is a function of the availability of a freshwater resource and the ability to construct an elevated water reservoir. This work reviews the technological feasibility of hydropower generation and also pumped hydro storage and its geographical distribution around the world. There is also an emphasis on installations in the Middle East and North Africa (MENA) in terms of available capacity as well as past and future developments and expansions. A discussion is presented on a project taking place in the United Arab Emirates (UAE) in the Hatta region, which has a water reservoir that would be fit for utilization for pumped hydro storage applications. Once the project is commissioned in 2024, it will provide an estimated 2.06 TWh per year, helping the UAE achieve the goal o... [more]

The vehicle-to-grid concept emerged very quickly after the integration of renewable energy resources because of their intermittency and to support the grid during on-peak periods, consequently preventing congestion and any subsequent grid instability. Renewable energies offer a large source of clean energy, but they are not controllable, as they depend on weather conditions. This problem is solved by adding energy storage elements, implementing a demand response through shiftable loads, and the vehicle-to-grid/vehicle-to-home technologies. Indeed, an electric vehicle is equipped with a high-capacity battery, which can be used to store a certain amount of energy and give it back again later when required to fulfill the electricity demand and prevent an energy shortage when the main-grid power is limited for security reasons. In this context, this paper presents a comparative study between two home microgrids, in one of which the concept of vehicle-to-home is integrated to provide a case... [more]

Energy storage systems is expected to be utilized to cover the increased electrification of energy demands and to alleviate the electrical energy production from intermittent energy sources such as solar and wind. Aggregated and distributed battery energy storage systems may improve electricity grids operability and security by providing smart energy management options and efficient resources allocation. In this paper, battery storage at the secondary distribution level is explored. The investigation is based on the end-user energy demand behavior. As such, the electrical energy consumption patterns are measured and analyzed in a residential area. Measurements were collected and analyzed in order to record the customers’ behaviors aiming to reveal their differences and similarities. Following this, aggregated and distributed battery energy storage systems are computed based on the features of the measured electrical power consumption patterns aiming to estimate the factors that could p... [more]

Indonesia has vast solar energy potential, far more than needed to meet all its energy requirements without the use of fossil fuels. This remains true after per capita energy consumption rises to match developed countries, and most energy functions are electrified to minimize the use of fossil fuels. Because Indonesia has relatively small energy potential from hydro, wind, biomass, geothermal and ocean energy, it will rely mostly on solar for its sustainable energy needs. Thus, Indonesia will require large amounts of storage for overnight and longer periods. Pumped hydro comprises 99% of global energy storage for the electricity industry. In this paper, we demonstrate that Indonesia has vast practical potential for low-cost off-river pumped hydro energy storage with low environmental and social impact; far more than it needs to balance a solar-dominated energy system.

The construction of nanostructured materials for their application in electrochemical processes, e.g., energy storage and conversion, or sensing, has undergone a spectacular development over the last decades as a consequence of their unique properties in comparison to those of their bulk counterparts, e.g., large surface area and facilitated charge/mass transport pathways. This has driven strong research on the optimization of nanostructured materials for the fabrication of electrochemical devices, which demands techniques allowing the assembly of hybrid materials with well-controlled structures and properties. The Layer-by-Layer (LbL) method is well suited for fulfilling the requirements associated with the fabrication of devices for electrochemical applications, enabling the fabrication of nanomaterials with tunable properties that can be exploited as candidates for their application in fuel cells, batteries, electrochromic devices, solar cells, and sensors. This review provides an u... [more]

This paper presents a novel methodology for planning and operating biogas energy systems based on the transactive energy concept to determine multilevel operating regimes for distributed generation. The developed model is used to manage the production, storage, and dispatch of biogas energy systems to meet the load demands of the biogas producer and support the operation of the distribution network operator. An Integer Linear Programming (ILP) is fitted to optimize the biogas production of the biogas producer, including the operation of the biogas storage systems and their interaction with the network operator. The model’s objective is to maximize benefits for the participating agents in a transactive energy context. The model’s effectiveness is validated using seven case studies involving biogas systems having different operating ranges and modes to achieve enhanced flexibility and reliability for the system operation with a large proportion of intermittent energy resources. The simul... [more]

Energy storage (ES) is playing an increasingly important role in reducing the spatial and temporal power imbalance of supply and demand caused by the uncertainty and periodicity of renewable energy in the microgrid. The utilization efficiency of distributed ES belonging to different entities can be improved through sharing, and considerable flexibility resources can be provided to the microgrid through the coordination of ES sharing and demand response, but its reliability is affected by multiple uncertainties from different sources. In this study, a two-stage ES sharing mechanism is proposed, in which the idle ES capacity is aggregated on the previous day to provide reliable resources for real-time optimization. Then, a two-layer semi-coupled optimization strategy based on a deep deterministic policy gradient is proposed to solve the asynchronous decision problems of day-ahead sharing and intra-day optimization. To deal with the impact of multiple uncertainties, Monte Carlo sampling i... [more]