Adsorption chillers with desalination functionality, being devices characterised by very low electricity consumption, provide an alternative to conventional sources of cooling and water. The option of desalinating water means that the use of a single device enables obtaining two useful products. Adsorption chillers are not widely used at present. due to their low performance characteristics; these are, however, constantly being improved. This paper presents a verification of the possibility of increasing the cooling coefficient of performance (COP) and specific cooling power (SCP) of a laboratory adsorption chiller by optimising the length of cycle times and using a copper additive to silica gel with a mass fraction of 15% to increase heat transport in the bed. The choice of copper among other considered additives was determined by the conclusions from the research on the sorption kinetics of various mixtures, price and availability, and a high thermal conductivity. The device was oper... [more]

This paper presents the results of numerical tests on the elements of an adsorption chiller that comprises a sorption chamber with a bed, a condenser, and an evaporator. The simulation is based on the data and geometry of a prototype refrigeration appliance. The simulation of this problem is unique and has not yet been performed, and so far, no simulation of the phenomena occurring in the systems on a real scale has been carried out. The presented results are part of the research covering the entire spectrum of designing an adsorption chiller. The full process of numerical modeling of thermal and flow phenomena taking place in the abovementioned components is presented. The computational mesh sensitivity analysis combined in the k-ε turbulence model was performed. To verify and validate the numerical results obtained, they were compared with the results of tests carried out on a laboratory stand at the AGH Center of Energy. The results of numerical calculations are in good agreement wi... [more]

The intensive development of the world economy and the expected population growth mean that demand for cooling and water will continue to rise. The use of conventional technologies to meet this demand is associated with an enormous expenditure of electricity, which still comes mainly from non-renewable sources. With the increasing demand for energy, the increasing scarcity of drinking water, and the negative impact of humankind on the environment due to global warming and ozone depletion, intensive research has been carried out to find modern desalination technologies Most of the technologies use electricity for the process of desalination, and over 6% of the world’s electricity is generated from non-renewable sources, thus increasing the emissions of harmful pollutants into the atmosphere. One possibility to reduce emissions is the use of adsorption chillers with desalination function, which allow the production of cooling simultaneously with the process of water desalination. These s... [more]

In this work, the influence of temperature on textural, morphological, and crystalline characterization of bio-adsorbents produced by hydrothermal carbonization (HTC) of corn stover was systematically investigated. HTC was conducted at 175, 200, 225, and 250 °C, 240 min, heating rate of 2.0 °C/min, and biomass-to-H2O proportion of 1:10, using a reactor of 18.927 L. The textural, morphological, crystalline, and elemental characterization of hydro-chars was analyzed by TG/DTG/DTA, SEM, EDX, XRD, BET, and elemental analysis. With increasing process temperature, the carbon content increased and that of oxygen and hydrogen diminished, as indicated by elemental analysis (C, N, H, and S). TG/DTG analysis showed that higher temperatures favor the thermal stability of hydro-chars. The hydro-char obtained at 250 °C presented the highest thermal stability. SEM images of hydro-chars obtained at 175 and 200 °C indicated a rigid and well-organized fiber structure, demonstrating that temperature had... [more]

Corn straw, a typical agricultural waste, was directly converted into hydrochar with a yield of 77.56% by hydrothermal carbonization at 140−230 °C for 2 h with a solid−liquid ratio of 1:20. The morphology and surface properties were characterized by elemental analysis, specific surface area and pore size analysis and Fourier transform infrared spectroscopy. The results showed that with the increase of hydrothermal reaction temperature, some physical and chemical properties such as the increase of hydrocarbon content, crystallinity, and specific surface area of hydrochar changed significantly. A series of chemical reactions such as dehydration, decarboxylation, and aromatization occurred in the hydrothermal carbonization process so that the prepared hydrochar had rich oxygen-containing functional groups (-HO, C-O-C, C=O) and unique porous structure made the hydrochar prepared at 170 °C had the best removal effect on Cd2+ in solution (5.84 mg/g). These specific conditions could remove Cd... [more]

Plastic waste generation has increased dramatically every day. Indiscriminate disposal of plastic wastes can lead to several negative impacts on the environment, such as a significant increase in greenhouse gas emissions and water pollution. Therefore, it is wise to think of other alternatives to reduce plastic wastes without affecting the environment, including converting them into valuable products using effective methods such as pyrolysis. Products from the pyrolysis process encompassing of liquid, gas, and solid residues (char) can be turned into beneficial products, as the liquid product can be used as a commercial fuel and char can function as an excellent adsorbent. The char produced from plastic wastes could be modified to enhance carbon dioxide (CO2) adsorption performance. Therefore, this review attempts to compile relevant knowledge on the potential of adsorbents derived from waste plastic to capture CO2. This review was performed in accordance with PRISMA guidelines. The pl... [more]

Acid treatments are one of the methods for intensifying oil and gas production. Corrosion is a significant factor affecting the performance of oilfield equipment. There are many different methods of preventing corrosion, but corrosion inhibitors are most commonly used in industry. The protective effect of the inhibitor is directly determined by the effective adsorption of surfactants on the metal surface. For an indirect assessment of the adsorption of the inhibitor, a comprehensive research method is proposed based on the determination of the interfacial tension of acid compositions and steel plates’ contact angle of wetting after corrosion tests. It was found that in hydrochloric acid the adsorption of the inhibitor IC-1 reaches a maximum after 6 h, an increase in the acid concentration in the range of 5−15% wt. has a negative effect on the activity of the inhibitor. For sulfamic acid, the maximum adsorption of the IC-2 inhibitor is observed after 24 h, an increase in acid concentrat... [more]

The efficient recovery of low temperature waste heat, representing from 25% up to 55% of the energy losses in industrial processes, still remains a challenge and even Organic Rankine Cycles (ORCs) experience a strong efficiency decay in such a low temperature operating range (T < 150 °C). In similar heat transfer processes, several nanofluids have been proposed as a solution for increasing heat transfer efficiency, but they produced only moderate enhancements of the heat transfer efficiency in comparison with pure fluids. This paper aims at numerically assessing the potential gain in efficiency deriving from the application of an unconventional type of nanoparticles, the metal-organic heat carriers (MOHCs), in the ORC field. In comparison with standard nanoparticles, these MOHCs make it possible to extract additional heat from the endothermic enthalpy of desorption, with a theoretically high potential for boosting the heat transfer capacity of ORC systems. In this paper a numerical... [more]

Deep marine shale gas reservoirs are extremely rich in the Sichuan basin in China. However, due to the in situ conditions with high temperature and high pressure (HTHP), in particular reservoir pressure being usually much higher than the test pressure, it is difficult to accurately clarify the adsorption behavior, as seepage theory plays an important role in shale gas reserves evaluation. Therefore, three kinds of sorbent, including illite, quartz and kerogen, and two simulation methods, containing the grand canonical ensemble Monte Carlo method and molecular dynamics method, are synthetically used to determine the methane adsorption behavior under HTHP. The results show that both absolute adsorption and excess adsorption decrease with the increase of temperature. When the pressure increases, the absolute adsorption increases quickly and then slowly, and the excess adsorption first increases and then decreases. The superposition of wall potential energy is strongest in a circular hole,... [more]

The emission of mercury from coal combustion has caused consequential hazards to the ecosystem. The key challenge to abating the mercury emission is to explore highly efficient adsorbents. Herein, sulfur-functionalized carbon (S-C) was synthesized by using a molten-salt pyrolysis strategy and employed for the removal of elemental mercury from coal-combustion flue gas. An ideal pore structure, which was favorable for the internal diffusion of the Hg0 molecule in carbon, was obtained by using a SiO2 hard template and adjusting the HF etching time. The as-prepared S-C with an HF etching time of 10 h possessed a saturation Hg0 adsorption capacity of 89.90 mg·g−1, far exceeding that of the commercial sulfur-loaded activated carbons (S/C). The S-C can be applied at a wide temperature range of 25−125 °C, far exceeding that of commercial S/C. The influence of flue gas components, such as SO2, NO, and H2O, on the Hg0 adsorption performance of S-C was insignificant, indicating a good applicabili... [more]

The ultra-deep removal of thiophene is essential for the conversion of coke oven gas to methane and metal modified Y zeolite has excellent thiophene adsorption capacity. The effects of temperature on chemisorption between metal modified Y zeolite and thiophene and the reductive gases in coke oven gas on the thiophene adsorption performance still remains ambiguous. To address the aforementioned aims, series of NaMY (M = Ce, Ni, Zn and Ag) were prepared via ion-exchanged with Na+ of NaY, and two comparable sets of thiophene adsorption evaluation were conducted in a fixed bed reactor: (1) NaY and NaMY were evaluated at different temperatures in simulated coke oven gas, and (2) NaCeY was evaluated in N2 and different reductive atmospheres. The results show that NaNiY, NaZnY and NaAgY could adsorb thiophene via π-complexation, however, NaCeY mainly through S-Ce bond. Π complexation becomes weak above 150 °C, and the strength of S-Ce bond varies little when the temperature rises to 250 °C. C... [more]

The surface properties of coal, interactions with gaseous and vapour media, and knowledge of the pore structure are important in terms of preparation, use, and utilisation of coal. This publication combines new unpublished data with analyses included in earlier publications by the research team to expand and systematise information on the sorption of water vapour, methanol vapour, and the saturated and unsaturated hydrocarbons hexane, 1-hexene, heptane, 1-heptene, octane on coals of different ranks. The study showed that the affinity of coal for water and methanol is related to the content of oxygen in the coal rather than the rank of the coal. Water sorption is a multilayer phenomenon, while methanol sorption is a monolayer phenomenon. The water monolayer is greater than that of methanol for low-rank coal, but for the higher-rank coals it is the opposite. The sorption capacity of the applied hydrocarbons depends on the presence or absence of a double bond and the size of the molecule.... [more]

Solid hydrochar (HC) produced by hydrothermal carbonization (HTC) of tomato plant biomass from a greenhouse (GH) was assessed for different inhouse applications, including fuel, seed germination, and leached GH nutrient feed (GNF) wastewater treatment. Completed experiments showed encouraging results. HC was revealed to be an efficient renewable fuel, having peat-like characteristics with high heating value of about 26.0 MJ/kg and very low clinker forming potential. This would allow the use of HC as fuel for GH heating as a substitute to costly natural gas, or it could be commercialized after pelletizing. Experiments with soil application showed substantial potential for the produced HC in better seed germination of tomato plants. Another benefit from use of the produced HC is as a soil additive, which would also contribute to environmental emission reduction. Results suggest that the generated HC can remove about 6−30% of nutrients from leached-GNF wastewater. This would be an essenti... [more]

This study investigates the capability of the Southeast Mesohellenic Trough (SE MHT) sandstone formations to serve as a potential reservoir for CO2 storage in response to the emerging climate change issues by promoting environmentally friendly mineral sequestration applications. Sandstone samples, for the first time, were evaluated for their petrographic characteristics, mineral chemistry, geochemical properties, as well as their petrophysical and gas adsorption properties through tests. The sandstones were tested and classified into distinct groups. The most promising site to be considered for pilot CO2 storage testing is the Pentalofos Formation locality since its sandstones display specific mineral phases with the proper modal composition to conceivably react with injected CO2, leading to the development of newly formed and stable secondary mineral phases. The gas adsorption results are also more encouraging for sandstones from this sedimentary formation. All the measured UCS (uniax... [more]

Given that vanadium is a valuable material, the implementation of vanadium recycling processes is thus necessary to enhance the element’s value chain as well as minimize its undesirable environmental consequences. Among various remediation methods available, a biological method based on microalgal adsorption is known to be eco-friendly and calls for further investigations. Herein, we evaluated V2O5 adsorption efficiencies of four different microalgal strains: Nannochloropsis oculata, Heterocapsa circularisquama, Chattonella marina, and Chattonella antiqua. Inductively coupled plasma mass spectrometry (ICP-MS) data indicated that vanadium concentration in the culture medium of Nannochloropsis oculata was reduced from 4.61 ± 0.11 mg L−1 to 1.85 ± 0.21 mg L−1 after being exposed to V2O5 solution for 24 h, whereas the supernatants of the other three strains displayed no change in vanadium ion concentration. Therefore, our results indicated a strong potential of Nannochloropsis oculata for... [more]

Wastewater treatment plants (WWTPs) are one of the most energy-intensive industries. Every stage of wastewater treatment consumes energy, which is the primary contributor to WWTP costs. Adsorbents and process optimization are critical for energy savings. The removal of dyes from industrial wastewater by adsorption using commercially available adsorbents is inefficient. Metal−organic frameworks (MOFs) have outstanding properties that can improve separation performance over current commercial adsorbents, and thus, these materials represent a milestone in improving dye removal in water treatment methods. In this work, three types of metal−organic frameworks (Fe-BTC, Cu-BTC, and ZIF-8) have been investigated as prospective adsorbents for methyl orange removal from water in batch setups. The results showed that at 15 mg/L MO initial concentration and 100 mg dosage, Fe-BTC had the highest removal efficiency of 91%, followed by ZIF-8 (63%), and finally Cu-BTC (35%), which exhibited structural... [more]

During the production process, water phase incursion into the reservoir causes water blocking damage and seriously affects the production of tight gas reservoirs. Recently, nanoemulsions have been used as highly effective water blocking removing agents in the field, but their mechanism is still unclear. In this research, a series of nanoemulsions with different droplet sizes were synthesized, and their water blocking removing performance was intensively investigated. To begin, the relationship between the droplet size and the chemical composition of the nanoemulsion was determined by dynamic light scattering. Second, the influence of the nanoemulsion droplet size on the surface tension and the contact angle experiments was studied. Finally, NMR and permeability recovery experiments were used to study the relationship between the droplet size and the water locking removing effect of the nanoemulsions. Simultaneously, the surfactant release process was investigated using the static adsor... [more]

A significant issue for the ecosystem is the presence of boron in water resources, particularly in produced water. Batch and dynamic experiments were used in this research to extract boron in the form of boric acid from aqueous solutions using boron selective resins, DIAION CRB05. DIAION™ CRB05 is an adsorbent that is effective in extracting boron from aqueous solutions due to its high binding capacity and selectivity for boron ions, and it is also regenerable, making it cost-effective and sustainable. Field Emission Scanning Electron Microscopy (FESEM), X-ray diffraction (XRD), and FTIR analysis for DIAION CRB05 characterization. To increase the adsorption capacity and find the ideal values for predictor variables such as pH, adsorbent dose, time, and boric acid concentration, the Box−Behnken response surface method (RSM) was applied. The dosage was reported to be 2000 mg/L at pH 2 and boron initial concentration of 1115 mg/L with 255 min for the highest removal anticipated from RSM.... [more]

The fate of radionuclides in the environment is attracting increased attention. The effect of various environmental effects on the adsorption behavior of the strontium ion (Sr2+) by red soil colloids in Southern China was studied by a series of batch experiments, and the adsorption mechanism was briefly investigated as well. With the increase in the solid−liquid ratio and the concentration of Sr2+, the adsorption efficiency increased gradually. The effect of pH and ionic strength on adsorption was strong, while temperature had little effect. The adsorption data fitted to the Langmuir model indicates that the process is monolayered and homogeneous. The thermodynamic parameters also show that the adsorption of Sr2+ on red soil colloids is a spontaneous and exothermic process. The aim of this work is to gain insight into the role of red soil colloids on the fate of radionuclides in the field.

Natural gas, biogas, and refinery gas all include H2S, which has adverse effects not only on the environment and human health but also on the equipment and catalysts that are employed in the relevant processes. H2S is removed from the aforementioned gases using a variety of techniques in order to fulfill the necessary sales criteria and for reasons of safety. The adsorption method stands out among various other approaches due to its straightforward operation, high level of efficiency, and low overall cost. This technique makes use of a variety of adsorbents, such as metal-organic frameworks (MOFs), activated carbon, and zeolites. The use of zeolite-based adsorbents is by far the most common of these various types. This is due to the specific properties of zeolite-based adsorbents, which include a high adsorption capacity, the ability to be regenerated, a high temperature stability, a diversity of types, the possibility of modification, high efficiency, and low cost. In addition, resear... [more]

This work aims to investigate the influence of temperature and chemical impregnation in the textural and morphological composition of the bio-adsorbent of bio-adsorption via thermal cracking of the seeds of açaí. The experiments were carried out at 400 °C and 450 °C using a pilot scale reactor. The efficiency of the organic process was calculated in terms of liquid and solid products selected with a chemical impregnation process with NaOH, mainly with the liquid that had a greater product conversion. The elementary samples of the solid products occur with the occurrence of carbonization with an increase in the temperature of the process and the presence of impregnation. The textural and morphological characterization occurred with an analysis of FT-IR, SEM/EDS, XRF, and B.E.T. The in-phase product was developed through the creation of açaí seed in nature and impregnated with NaOH solution (2 M) at temperatures of 400 °C and 450 °C. The adsorption kinetics of acetic acid were investigat... [more]

The design of an adsorption solar air conditioning system is investigated by using a model with an activated carbon−methanol working pair. This system is analysed with the solar insolation levels and ambient temperatures of Singapore. The proposed design mainly consists of two tubular reactor heat exchangers (TRHEXs) operating out of phase and driven by heat from an evacuated tube solar collector (ETSC). The pair of TRHEXs act as a thermal compressor and contain about 2.275 kg of activated carbon per reactor. The evacuated tube solar collector (ETSC) has better performance and is more cost effective than the flat plate solar collector (FPSC), even though it has a higher cost per unit. On the hottest day of the year, the proposed adsorption system has a maximum cooling power of 2.6 kW and a COP of 0.43 at a maximum driving temperature of 139 °C with a 9.8 m2 ETSC area. The system has a total estimated cost of EUR 10,550 corresponding to about SGD 14,800 with a 7-year payback time. At si... [more]

The superparamagnetic Fe3O4 nanoparticles as an absorbent with a size distribution of 4.8−6.4 nm were synthesized using a simple one-pot hydrothermal strategy at 200 °C for 24 h, where iron citrate and distilled were the sum total of raw materials. The as-synthesized Fe3O4 powders showed rapid and efficient adsorption for xylenol orange with a saturated adsorption amount of 42.5 mg/g according to Langmuir linear fitting, and the adsorption reaction between xylenol orange adsorbate and Fe3O4 adsorbent was mostly completed within 10 min. The Fe3O4 nanoparticles not only had superparamagnetism with a saturation magnetization value of 54.9 emu/g at 15 kOe but also possessed strong magnetic response, making them easy to separate easily from aqoeous solution under the attraction of magnet. In this work, the Fe3O4 particles can be totally attracted toward the magnet within 15 s, leaving the suspension a clear solution.

Bioadsorbent, obtained as a result of the processing of bio-waste, has recently gained popularity as a material that adsorbs greenhouse gases, mainly carbon dioxide. Bio-waste, mainly residues from food industry operations, is a waste to be landfilled or composted and can be a potential substrate for bioadsorbent production. Bioadsorbents used for carbon capture must, above all, have low production costs and high adsorption efficiency. This review covers popular bioadsorbents that have been tested for their ability to adsorb carbon dioxide. The paper compares bioadsorbent production methods, physicochemical properties, adsorption isotherms, surfaces, and their porosity. There is a lack of data in the literature on the topic of carbon dioxide adsorption on large-scale plants in the target environment. Therefore, further research needs to fill in the gaps to identify the promised potential of these bioadsorbents.

In this study, biochar was prepared via hybrid doping of N, O, and S by applying one-pot pyrolysis of poplar wood and S-containing urea formaldehyde at 900 °C. Different doping ratios were adopted, and the contents of O, N, and S were in the ranges of 2.78−5.56%, 2.16−4.92%, and 1.42−4.98%, respectively. This hybrid doping significantly enhanced the efficiency of the removal of tetracycline (40 mg/L) from wastewater to 71.84% in comparison with that attained by using normal poplar biochar (29.45%). The adsorption kinetics and isotherms indicated that the adsorption process was favorable and was dominated by chemisorption instead of physisorption; the dominant adsorption process may be justified by the existence of abundant functional groups. The adsorption capacity was barely related to the surface area (R2 = 0.478), while it was closely related to the concentration of graphitic N (R2 = 0.985) because graphitic N enhanced the π−π interactions. The adsorption capacity was also highly re... [more]