Using experimental data for the adsorption of phosphates out of wastewater on waste recycled bricks, published independently in MDPI Processes before (2020), this message re-visits the mathematical theory of the Freundlich adsorption model. It demonstrates how experimental data are to be deeper treated to model the saturation regime and to bridge a chasm between those areas where the data fit the Freundlich power function and where a saturation of surface adsorption centers occurs.

The simulation of carbon dioxide (CO2)-methane (CH4) mixed gas adsorption and the selectivity on zeolite 4A using Aspen Adsorption were studied. The influence of temperature ranging from 273 to 343 K, pressure up to 10 bar and various compositions of CO2 in the binary system were simulated. The findings of the study demonstrate that the models are accurate. In addition, the effects of various key parameters such as temperature, pressure, and various compositions of binary gases were investigated. The highest CO2 and CH4 adsorption are found at 273 K and 10 bar in the Langmuir isotherm model with 5.86 and 2.88 mmol/g, respectively. The amount of CO2 adsorbed and the selectivity of the binary mixture gas depends on the composition of CO2. The kinetics of adsorption for pure components of CO2 at high temperatures can reach saturation faster than CH4. The influence of the physical properties of zeolite 4A on kinetic adsorption were also studied, and it was observed that small adsorbent par... [more]

A novel manganese-rich pokeweed biochar was prepared at different temperatures from manganese-rich pokeweed plants collected at manganese tailings, resulting in materials identified as BC300, BC400, and BC500. The synthetized biochar materials were investigated as regards their potential for removing Cu2+, Pb2+, and Cd2+, specifically in terms of adsorption performances, adsorption kinetics, adsorption isotherms, and potential environmental pollution risk. The results showed that the sorption process fitted well to the pseudo-second-order kinetic and Langmuir models, and the maximum adsorption capacities of BC500 were 246, 326, and 310 mg·g−1 for Cu2+, Pb2+, and Cd2+ respectively. The physicochemical characteristics of the biochars, and the adsorption mechanisms, were revealed by using scanning electron microscopy-energy spectrometer, elemental analysis, Brunauer−Emmett−Teller techniques, X-ray diffraction, X-ray photoelectron spectroscopy, and Fourier transform infrared spectroscopy.... [more]

The insecticidal ingredient in a biogas solution being fully utilized by cation exchange resin to produce slow-release insecticide is of great social value. In this work, the feasibility of ammonia nitrogen in a biogas slurry loaded on resin as a slow-release insecticide was evaluated by studying the effect of adsorption and the slow release of ammonia nitrogen by resin. The effects of the ammonia nitrogen concentration, resin dosage, adsorption time and pH value on the ammonia nitrogen adsorption by the resin were studied. The results showed that the ion exchange resin had a good adsorption effect on the ammonia nitrogen. With the increase of the resin dosage, time and ammonia nitrogen concentration, the adsorption capacity increased at first and then stabilized. The ammonia nitrogen adsorption capacity reached its maximum value (1.13 mg) when the pH value was 7. The adsorption process can be fitted well by the Langmuir isothermal adsorption equation and quasi-second-order kinetic mod... [more]

The process of removing indium ions from aqueous solutions by applying capacitive deionization (CDI) is reported in this manuscript. First, a modified carbon material was prepared by incorporating titanium dioxide (TiO2) into activated carbon (AC). A microwave-assisted ionothermal synthesis (MAIS) method was used to produce evenly distributed nanostructured anatase TiO2 on the surface of AC. A polyurethane (PU) elastomer was then synthesized as the binder material instead of using conventional polyvinylidene fluoride (PVDF). By combining the aforementioned materials, a MAIS TiO2/AC-PU electrode was synthesized and applied to CDI tests. Scanning electron microscopy (SEM) was used to characterize the size and dispersion of the composites. For electrochemical properties, cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) were used to analyze the synthesized electrode. The performance of the prepared electrode during the CDI process was tested in different concentrati... [more]

Heavy metal pollution of aquatic media has grown significantly over the past few decades. Therefore, a number of physical, chemical, biological, and electrochemical technologies are being employed to tackle this problem. However, they possess various inescapable shortcomings curbing their utilization at a commercial scale. In this regard, nanotechnology has provided efficient and cost-effective solutions for the extraction of heavy metals from water. This review will provide a detailed overview on the efficiency and applicability of various adsorbents, i.e., carbon nanotubes, graphene, silica, zero-valent iron, and magnetic nanoparticles for scavenging metallic ions. These nanoparticles exhibit potential to be used in extracting a variety of toxic metals. Recently, nanomaterial-assisted bioelectrochemical removal of heavy metals has also emerged. To that end, various nanoparticle-based electrodes are being developed, offering more efficient, cost-effective, ecofriendly, and sustainable... [more]

The intensive exploitation of resources on a global level has led to a progressive depletion of mineral reserves, which were proved to be insufficient to meet the high demand for high-technological devices. On the other hand, the continuous production of Waste from Electrical and Electronic Equipment (WEEE) is causing serious environmental problems, due to the complex composition of WEEE, which makes the recycling and reuse particularly challenging. The average metal content of WEEE is estimated to be around 30% and varies depending on the manufacturing period and brand of production. It contains base metals and precious metals, such as gold and palladium. The remaining 70% of WEEEs is composed of plastics, resins, and glassy materials. The recovery of metals from WEEEs is characterized by two main processes well represented by the literature: Pyrometallurgy and hydrometallurgy. Both of them require the pre-treatment of WEEEs, such as dismantling and magnetic separation of plastics. In... [more]

Volatile organic compounds (VOCs) are intermittently emitted at high concentrations (tens of thousands of ppmv) from small-scale laundry shops in urban areas, affecting the urban atmospheric environment. In this study, we suggested integrating VOC treatment processes incorporating condensation and adsorption in series to remove VOCs released from small-scale laundry dryers (laundry weighing less than 30 kg). We designed two different processes depending on regeneration modes for adsorber beds; an open-circuit flow process and a closed-loop flow process in regeneration mode. Our VOC treatment processes enable sustainable operation via the regeneration of adsorbers on a regular basis. Before applying the VOC treatment processes, average concentration of total volatile organic compounds (TVOCs) was 4099 ppmv (12,000 ppmv of the peak concentration) during the drying operation. After applying our closed-loop flow process, TVOC concentration decreased to 58 ppmv, leading to 98.5% removal eff... [more]

Water pollution induced by the tetracycline (TC) has caused global increasing attention owing to its extensive use, environmental persistence, and potential harm for human health. Adsorption and advanced oxidation processes (AOPs) have been promising techniques for TC removal due to ideal effectiveness and efficiency. Magnetic composites (MCs) which exploit the combined advantages of nano scale, alternative sources, easy preparation, and separation from wastewater are widely used for catalysis and adsorption. Herein, we intensively reviewed the available literature in order to provide comprehensive insight into the applications and mechanisms of MCs for removal of TC by adsorption and AOPs. The synthesis methods of MCs, the TC adsorption, and removal mechanisms are fully discussed. MCs serve as efficient adsorbents and photocatalysts with superior performance of photocatalytic performance in TC degradation. In addition, the TC can be effectively decomposed by the Fenton-based and SO4•−... [more]

The adsorption of sodium dihydrogen phosphate (NaH2PO4) onto X- and Y-type faujasite zeolites was computationally studied using the Density Functional Theory (DFT) method. The structures were modeled using the Materials Studio software. The Si/Al ratios for the X- and Y-type zeolite models were 1.2 and 2.5, respectively. The central pore of the zeolite provided a more favorable coordination for adsorbing NaH2PO4. Full molecular optimization and adsorption energy calculations were performed using the VASP code. The adsorption was more effective on zeolite Y, with an adsorption energy of 161 kJ/mol, compared to the zeolite X system, with an adsorption energy of 31.64 kJ/mol. This calculated value for X-type faujasite was found in the interval of the adsorption energy of H2PO4− on hydrated Fe oxide (94.4 kJ/mol) and modified polyether sulfone (22.5 kJ/mol), and the calculated adsorption energy of the molecule on Y-type faujasite coincides with the reported value for this adsorbate on Mg/C... [more]

An L-glutathione-functionalized silica adsorbent was applied in this study to remove malathion from aqueous media. This adsorbent has demonstrated an improved adsorption efficiency of malathion. The maximum uptake achieved was 130 mg g−1 at pH 8. Equilibrium was reached after about 90 min. A pseudo-second-order model best described the adsorption kinetics. The adsorption isotherms were best simulated by the Freundlich model. The functional groups are thermally stable up to about 150 °C. The elemental analysis results indicated high glutathione ligand densities. The results of this study show that the environmentally friendly L-glutathione functionalized silica is a promising candidate for the removal of malathion from water at the industrial level.

The utilization of adsorptive nonwovens as a pretreatment unit may lead to novel, cost-efficient wastewater treatment technologies with remarkable properties for environmental protection, such as efficient adsorption of antibiotics. This paper uses graphene-modified nonwoven (GMN) to examine (i) how the adsorption of tetracycline (TCY)—especially since this antibiotic is frequently detected in the environment—takes place on an environmentally relevant concentration scale, and (ii) what factors influence the antibacterial and antifungal properties profile of this material class. This study demonstrates that combining graphene particles with commercial textile auxiliaries clearly enhances the antibacterial and antifungal properties of the modified nonwoven materials. The enzyme-linked immunosorbent assay (ELISA) was used to detect the TCY residues at ng/mL scale. The adsorption results follow Henry and Redlich−Peterson isotherms and emphasize the adsorption process at low concentration l... [more]

The main aim of this study was to perform a parametric study for treating a model dye containing wastewater (i.e., methylene blue, MB) using locally available biomass wastes in Palestine as the adsorbent. Eight different types of biomasses were investigated in batch adsorption tests, including coffee grains, almond shells, pistachio shells, date pits, jute sticks, sunflower shells, peanut shells, and grapevine sticks. The experiments were conducted on three different phases of processing for these materials: as natural adsorbents, biochar, and activated carbon. The biochar was prepared by pyrolysis, while ZnCl2 was used to chemically activate the materials for obtaining activated carbon. The influences of pH, initial MB concentration, and adsorbent dosage on the adsorption capacity and kinetics were investigated for activated carbon obtained from sunflower shells. The results indicate that the adsorption efficiency of natural adsorbents and biochar is highly dependent on the biomass ty... [more]

Michigan State University-2 (MSU-2) is notable potential adsorbent for carbon dioxide (CO2) due to its intrinsic properties, which include its highly interconnected three-dimensional (3D) wormhole-like framework structure, high specific surface area, and its large total pore volume, as well as its large amount of surface silanol hydroxyl groups, which facilitate the amine functionalization process. In this study, unfunctionalized MSU-2 was synthesized via a fluoride-assisted two-step process via the solution precipitation method, using Triton X-100 as the surfactant and tetraethylorthosilicate (TEOS) as the silica precursor. Then, the synthesized MSU-2 was functionalized using varying tetraethylenepentamine (TEPA) loadings of 20−60 wt%. The effect of different TEPA loadings on the properties and CO2 adsorption capacity of the MSU samples was investigated. Studies of the CO2 adsorption of the unfunctionalized and TEPA-functionalized MSU-2 samples was conducted at 40 °C and 1 bar of pres... [more]

The exploration and rational design of easily separable and highly efficient sorbents with satisfactory capability of extracting radioactive uranium (U)-containing compound(s) are of paramount significance. In this study, a novel magnetic hydroxyapatite (HAP) composite (HAP@ CoFe2O4), which was coupled with cobalt ferrite (CoFe2O4), was rationally designed for uranium(VI) removal through a facile hydrothermal process. The U(VI) ions were rapidly removed using HAP@ CoFe2O4 within a short time (i.e., 10 min), and a maximum U(VI) removal efficiency of 93.7% was achieved. The maximum adsorption capacity (Qmax) of the HAP@CoFe2O4 was 338 mg/g, which demonstrated the potential of as-prepared HAP@CoFe2O4 in the purification of U(VI) ions from nuclear effluents. Autunite [Ca(UO2)2(PO4)2(H2O)6] was the main crystalline phase to retain uranium, wherein U(VI) was effectively extracted and immobilized in terms of a relatively stable mineral. Furthermore, the reacted HAP@CoFe2O4 can be magnetically... [more]

Textile effluent containing azo dyes such as C.I. Acid Violet 1 (AV1) can be degraded to toxic aromatic amines in the environment. Thus, there is a legitimate need to treat such effluents before they are discharged to surface waters. Two methods were proposed to remove AV1 from aqueous solutions: adsorption and advanced oxidation processes (AOPs). The sorption capacity of the strongly basic anion exchanger Purolite A520E of the polystyrene matrix determined from the Langmuir isotherm model was found to be 835 mg/g, while that of Lewatit S5428 of the polyacrylamide matrix Freundlich model seems to be more appropriate for describing the experimental data. The pseudo-second-order kinetic model and external diffusion are the rate limiting steps of adsorption. The removal efficiency of AV1 by the anion exchangers was higher than 99% after 40 min of phase contact time. AOPs involved the usage of hydrogen peroxide and peracetic acid (PAA) as oxidizing agents, while Fe2+ and simulated sunlight... [more]

An open system based on physical adsorption phenomena with humid air and zeolite 13X is herein discussed for residential heat storage purposes. A model has been developed to describe the conservation of mass and heat in the system. A simplified approach of a complete model describing both mass conservation in the macroporous and microporous domains is used based on the linear driving force (LDF) model. Local mass and heat transfer properties have been used. To describe the equilibrium, the Aranovich−Donohue isotherm model is selected. As an example, the developed model is compared and fitted to experimental data from a pilot scale system. A parametric study on operating and design parameters is given to understand their effect on the amount and/or duration of heat supply, concentration, and temperature profiles. The studied parameters are the inlet adsorbate concentration, fluid temperature, and velocity, as well as particle and zeolite crystal sizes. This analysis shows that an identi... [more]

Due to the widespread use of antibiotics in medical treatment, animal husbandry and aquaculture, a large number of antibiotics are discharged into the environment as metabolites or in their original state, causing pollution to water bodies, which is a serious issue. In this study, a novel nanocomposite adsorbent MIL-53/D201 was successfully prepared by hydrothermal synthesis. This approach overcomes the disadvantage of easy dissociation of MOF material in the water phase and realizes the efficient removal of antibiotic azlocillin sodium in water. The crystal morphology and basic structure of the composites were characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), energy scattering spectroscopy (EDS), and specific surface area and porosity analyzer (BET). The results showed that MIL-53 was successfully synthesized in situ in D201. The results of adsorption experiments show that the maximum saturated adsorption capa... [more]

Cotton dyeing is a very complex process with many variables in which different phenomena occur simultaneously. This study aimed to describe the cotton dyeing process by natural dye, using a mathematical model that consists of three mass conservation equations that depict dyeing cotton in cones, taking a representative volume element at the micro, meso, and macroscales. The first equation describes the concentration changes of the dye in the solution, taking into account the diffusive, convective, adsorptive, and reactive effects. The second equation describes the changes in dye concentration in cotton fiber, considering the diffusive, adsorptive, and reactive effects within an intermediate scale. The last equation describes changes in the concentration of dye in the solution on the macroscale, based on the characteristics of the equipment and the difference in concentration before and after passing through the fiber. In addition, a fluid continuity equation was incorporated, taking int... [more]

The removal of pharmaceuticals from wastewater is critical due to their considerable risk on ecosystems and human health. Additionally, they are resistant to conventional chemical and biological remediation methods. Two-dimensional nanomaterials are a promising approach to face this challenge due to their combination of high surface areas, high electrical conductivities, and partially optical transparency. This review discusses the state-of-the-art concerning their use as adsorbents, oxidation catalysts or photocatalysts, and electrochemical catalysts for water treatment purposes. The bibliographic search bases upon academic databases including articles published until August 2021. Regarding adsorption, high removal capacities (>200 mg g−1) and short equilibrium times (<30 min) are reported for molybdenum disulfide, metal-organic frameworks, MXenes, and graphene oxide/magnetite nanocomposites, attributed to a strong adsorbate-adsorbent chemical interaction. Concerning photocatalysis... [more]

The presence of major heavy metals including Pb2+, Cu2+, Co2+, Ni2+, Hg2+, Cr6+, Cd2+, and Zn2+ in water is of great concern because they cannot degrade or be destroyed. They are toxic even at very low concentrations. Therefore, it is necessary to remove such toxicants from water. In the current study, polydopamine carbon nanotubes (PD-CNTs) and polysulfone (PS) composite membranes were prepared. The structural and morphological features of the prepared PDCN composite membranes were studied using FTIR, XRD, SEM, and EDS. The potential application of PDCNs for heavy metal removal was studied for the removal of Pb2+, Cr6+, and Cd2+ from wastewater. The maximum removal efficiency of 96.1% was obtained for Cr6+ at 2.6 pH using a composite membrane containing 1.0% PD-CNTs. The removal efficiencies decreased by 64.1 and 73.4, respectively, by enhancing the pressure from 0.50 up to 0.85 MPa. Under the same circumstances, the percentages of Pb+2 removal at 0.49 bar by the PDCNS membranes conta... [more]

Coal maceral composition has a great effect on gas adsorption and diffusion. The interaction between maceral composition and supercritical CO2 (SCCO2) fluid will affect gas diffusion behavior in coals. Thus, the diffusivity derived from adsorption kinetics of CH4 and CO2 in vitrinite- and inertinite-rich coals with low-violate bituminous rank collected from the Hancheng mine of the Weibei coalfield pre- and post-SCCO2 fluid exposure (SFE) were tested at the conditions of 45 °C and 0.9 MPa. In combination with pore distribution and functional group content, the possible mechanism of the alterations in gas diffusion characteristics in coals with various maceral compositions was addressed. The results show that for vitrinite-rich coals, SFE increases the macropore apparent diffusion coefficient of CH4, while this treatment decreases the micropore apparent diffusion coefficient of CH4. However, the reverse trend is found for CO2 diffusion−adsorption rate. For inertinite-rich coals post-SFE... [more]

Because of increasing environmental awareness, it is becoming more important to remove harmful elements from water solutions. This study used activated carbon (AC) derived from waste wood-based panels as the base material, oxidized with nitric acid (OAC), and grafted with iminodiacetic acid (IDA-OAC) to improve the adsorption capacity and affinity for metals. The characterization of AC, OAC, and IDA-OAC was conducted via FTIR, SEM, N2 adsorption and desorption analysis, elemental analysis, Boehm titration, and point of zero charge (PZC). The instrument studies proved the modified increasing of the functional groups of the adsorbents. Moreover, batch and column experiments were conducted to evaluate the ability of the three adsorbents to remove copper ions from aqueous solution. In batch sorption, IDA-OAC had the highest adsorption capacity (84.51 mg/g) compared to OAC (54.74 mg/g) and AC (24.86 mg/g) at pH 5. The breakthrough point (Ct/Ci = 0.05) of copper ions for IDA-OAC occurred muc... [more]

Growth in the human population and intensive, large-scale farming results in a lowering in the quality of nutrition. An oversupply of food energy is often accompanied with a deficiency in micronutrients. To address this problem, the food industry provides products enriched with bioactive substances. The main challenge of this technology is the even distribution of micronutrients in the matrix of the fortified food. A possible solution to this challenge is to use stable and effective carriers. The aim of this work was to verify the applicability of native potato starch and modified starches (commonly used in the food industry) as carriers for microelements. Adsorptions were carried out in starch suspensions at a temperature below gelatinisation. The native potato starch and the modified starches (E 1404, E 1412, E 1420, and E 1422) were assessed for their effectiveness in adsorbing copper, iron, and zinc sulphates or gluconates. Pasting characteristics were analysed using a Brabender vi... [more]

The chemical surface of Santa Barbara Amorphous-15 (SBA-15) was functionalized with polyaniline (SBA-15/PA) and was prepared using aniline and ammonium persulfate as the modifying agent and oxidant. The samples were characterized by N2 physical adsorption at 77 K. SBA-15’s surface area was 654.5 m2 g−1, changing to 254.6 m2 g−1. The total acidity and basicity were determined using a modified Boehm’s method, and the point of zero charge pH (pHpzc) was determined. Immersion calorimetry in water, benzene, and NaOH, HCl, and phenol (100 mg L−1) solutions was performed, producing values ranging from −15.1 to −174.1 J g−1 related to the chemical surface, pHpzc, and acid and base group values. Finally, the phenol adsorption capacity was found to be higher for the modified polyaniline silica, at 138 mg g−1.