Hot flaring, even from quite high flare stacks, may result in significant heat radiation outside a facility to, e.g., public roads where random passersby may be exposed. The present study suggests a novel method for analyzing a typical flare heat radiation exposure and investigates skin burns that may be inflicted on an exposed person if a facility needs to depressurize in an emergency situation. A typical radiation field from an ignited natural gas vent was taken as the boundary condition, and these values were compared to radiation levels mentioned by the American Petroleum Institute (API 521), e.g., 1.58 kW/m2 and above. Due to facility perimeter fences along roads in larger industry areas, it was assumed that an exposed person may flee along a road rather than in the ideal direction away from the flare. It was assumed that naked skin, e.g., a bare shoulder or a bald head is exposed. The Pennes bioheat equation was numerically solved for the skin layers while the person escapes alon... [more]

This work is focused on the development and validation of a spark advance controller, based on a piston “damage” model and a predictive knock model. The algorithm represents an integrated and innovative way to manage both the knock intensity and combustion phase. It is characterized by a model-based open-loop algorithm with the capability of calculating with high accuracy the spark timing that achieves the desired piston damage in a certain period, for knock-limited engine operating conditions. Otherwise, it targets the maximum efficiency combustion phase. Such controller is primarily thought to be utilized under conditions in which feedback is not needed. In this paper, the main models and the structure of the open-loop controller are described and validated. The controller is implemented in a rapid control prototyping device and validated reproducing real driving maneuvers at the engine test bench. Results of the online validation process are presented at the end of the paper.

This article presents the results of the optimization of steam generator control systems powered by mixtures of liquid fuels containing biofuels. The numerical model was based on the results of experimental research of steam generator operation in an open system. The numerical model is used to build control algorithms that improve performance, increase efficiency, reduce fuel consumption and increase safety in the full range of operation of the steam generator and the cogeneration system of which it is a component. In this research, the following parameters were monitored: temperature and pressure of the circulating medium, exhaust gas temperature, oxygen content in exhaust gas, percentage control of oil burner power. Two methods of controlling the steam generator were proposed: the classic one, using the PID regulator, and the advanced one, using artificial neural networks. The work shows how the model is adapted to the real system and the impact of the control algorithms on the effic... [more]

Sustainable Development Goals were established by the United Nations General Assembly to ensure that everyone has access to clean, affordable, and sustainable energy. Third-generation biodiesel derived from algae sources can be a feasible option in tackling climate change caused by fossil fuels as it has no impact on the human food supply chain. In this paper, the combustion and emission characteristics of Azolla Pinnata oil biodiesel-diesel blends are investigated. The multi-objective response surface methodology (MORSM) with Box−Behnken design is employed to decrease the number of trials to conserve finite resources in terms of human labor, time, and cost. MORSM was used in this study to investigate the interaction, model prediction, and optimization of the operating parameters of algae biodiesel-powered diesel engines to obtain the best performance with the least emission. For engine output prediction, a prognostic model is developed. Engine operating parameters are optimized using... [more]

Variable moment of inertia systems are common, and a popular laboratory system of this type is the “ball-and-beam”. Such systems are, however, nonlinear and often unstable. Efficient control requires full state information (or at least partial velocities), which are generally difficult to measure. That is why the design of state observers is a relevant problem. In this paper, a new design of an observer is proposed. This new nonlinear observer uses partial output injection and the circle criterion to ensure semiglobal stability. Moreover, we present a complete modeling of the system and systematic testing of the observer in comparison to a baseline in the form of a linear observer. The results show that the designed observer outperforms its linear counterpart and does not impede control.

In the last decade, China has sharply tightened the monitoring values for wastewater treatment plants (WWTPs). In some regions with sensitive discharge water bodies, the values (24 h composite sample) must be 1.5 mg/L for NH4-N and 10 mg/L for total nitrogen since 2021. Even with the previously less strict monitoring values, around 50% of the wastewater treatment plants in China were permanently unable to comply with the nitrogen monitoring values. Due to the rapid changes on-site to meet the threshold values and the strong relation to energy-intensive aeration strategies to sufficiently remove nitrogen, WWTPs do not always work energy-efficiently. A Chinese WWTP (450,000 Population equivalents or PE) with upstream denitrification, a tertiary treatment stage for phosphorus removal and disinfection, and aerobic sludge stabilisation was modelled in order to test various concepts for operation optimisation to lower energy consumption while meeting and undercutting effluent requirements. F... [more]

Although gas desorption is a known phenomenon, modeling fluid flow in tight gas reservoirs often ignores the governing desorption effect, assuming that viscous transport is the predominant controller, resulting in an erroneous prediction of mass transport and fluid flow calculations. Thus, developing a new model accommodating all the major contributing forces in such a medium is essential. This work introduces a new comprehensive flow model suitable for tight unconventional reservoirs, including viscous, inertia, diffusion, and sorption forces, to account for fluid transport. Based on Langmuir law and Knudsen diffusion effect, three models were generated and compared with different known models using synthetic data. The model was solved and analyzed for different scenario cases, and parametric studies were conducted to evaluate the desorption effect on different reservoir types using MATLAB. Results show that the contribution of the sorption mechanism to the flow increases with the red... [more]

The growing interest in the negative environmental impact of overhead power lines of high and extra-high voltage stems from the increasing ecological awareness of societies. Consequently, a number of respective legal restrictions have been issued and actions have been undertaken to reduce this impact, especially in the electric field of the power frequency. The aim of this paper is to analyze the possibilities of reducing the width of electric field influence zones by changing the design parameters of power lines and defining the spatial distribution of its conductors. This analysis was carried out using the developed and experimentally verified models for determining the electric field and audible noise in the power line environment. The computational models were used to analyze the width of the electric field influence zones of 400 kV lines and the noise levels at the borders of these zones. The research focused on single and double circuit 400 kV power lines. It was revealed that a... [more]

In recent years, a growing number of enterprises have taken different steps to reduce the energy consumption and carbon emissions of information and communication technology (ICT) assets. Because of the expansion of digitalization and the need for rapid access to information, enterprises have been compelled to optimize the location and utilization of their ICT hardware. In this context, this paper presents a novel method based on a mixed-integer linear programming approach for optimizing the physical location and task allocation of printing devices in office floor plans considering the power usage of the ICT assets, the costs related to the purchase and service of the individual devices, operating costs, and distance between employees and printing devices. The applicability of the proposed model is illustrated using the case study of a company with 100 functional departments located in several office buildings across Poland. The results reveal that the model guarantees the execution of... [more]

This article proposes a model of an actual photovoltaic installation situated in the Gdynia Maritime University, Poland. This model is formulated in the form of a SPICE network. In the presented model, the influence of selected weather parameters and thermal phenomena on the properties of the components of this installation are taken into account. The structure of the analyzed installation and the form of the formulated model are both presented. By means of this model, values of the power produced by the installation considered in different seasons and different times of the day are computed. The obtained computation results are compared to the measurement results. Good agreement between the results of measurements and computations is obtained. The obtained results of the investigations confirm the considerable influence of weather conditions, as well as daily and seasonal changes in solar irradiation and the ambient temperature, on the electrical energy produced. In the summer months,... [more]

Due to the substantial amounts of money involved and the complex interactions of a number of different factors, managers of oil and gas companies are faced with significant challenges when making investment decisions that will increase business efficiency and achieve competitive advantages, especially through cost control. Due to the various uncertainties of the current period, optimal investment strategies are difficult to determine. Thus, through an economic analysis that includes data analysis, quantitative risk analysis scenarios, modelling and simulations, a work framework, in the form of a generic algorithm, is proposed with the aim of generating a complex procedure for optimizing investment decisions in oil field development. A complex set of elements is considered in the analysis: costs (operational expenditures (OPEX) and capital expenditures (CAPEX), daily drilling rig costs), prices (oil, gas, separation and water injection preparation), production profiles, different types... [more]

Due to the increasing integration of renewable energy sources (RES) and a corresponding reduction of conventional generating units, there is nowadays a demand from the power-electronic converters to provide grid-forming properties through proper control of the converter systems. This paper aims to evaluate the impact of various control loops in a grid-forming control strategy equipped with a fault-ride through capability on the passivity properties of the converter system. Through the analysis of the frequency-dependent input admittance of the converter, the main factors affecting the passivity properties are identified. A simplified analytical model is derived in order to propose possible control modifications to enhance the system’s passivity at various frequencies of interest and the findings are validated through detailed time-domain simulations and experimental tests.

One of the alternatives to reduce CO2 emissions from industrial sources (mainly the oil and gas industry) is CO2 capture. Absorption with chemical solvents (alkanolamines in aqueous solutions) is the most widely used conventional technology for CO2 capture. Despite the competitive advantages of chemical solvents, the technological challenge in improving the absorption process is to apply alternative solvents, reducing energy demand and increasing the CO2 captured per unit of solvent mass. This work presents an experimental study related to the kinetic and thermodynamic analysis of high-pressure CO2 capture using ethylenediamine (EDA) as a chemical solvent. EDA has two amine groups that can increase the CO2 capture capacity per unit of solvent. A non-stirred experimental setup was installed and commissioned for CO2 capture testing. Tests of the solubility of CO2 in water were carried out to validate the experimental setup. CO2 capture testing was accomplished using EDA in aqueous soluti... [more]

This paper presents the results of experimental tests of the impulse response of selected, essential components of a drone. A standardized lightning pulse that is often used during immunity tests of electronic devices in the aviation industry was applied. A single-stroke voltage impulse generator, MIG0618SS, was capable of producing the desired pulses. The input voltage was injected into selected electronic circuits of the drone system and pulses were observed in different parts of the machine. This allowed us to build a model based on the transmittance of the circuits most exposed to lightning overvoltages. The conducted tests were supported by impedance measurements carried out with an LCR-8110G meter. The obtained results made possible the development of a preliminary drone simulation model, allowing us to determine the size of the disturbances arising in individual circuits during nearby lightning. A discussion of the influence of close lightning discharges on expected induced over... [more]

This work aims to model the combined cycle power plant (CCPP) using different algorithms. The algorithms used are Ridge, Linear regressor (LR), and upport vector regressor (SVR). The CCPP energy output data collected as a factor of thermal input variables, mainly exhaust vacuum, ambient temperature, relative humidity, and ambient pressure. Initially, the Ridge algorithm-based modeling is performed in detail, and then SVR-based LR, named as SVR (LR), SVR-based radial basis function—SVR (RBF), and SVR-based polynomial regression—SVR (Poly.) algorithms, are applied. Mean absolute error (MAE), R-squared (R2), median absolute error (MeAE), mean absolute percentage error (MAPE), and mean Poisson deviance (MPD) are assessed after their training and testing of each algorithm. From the modeling of energy output data, it is seen that SVR (RBF) is the most suitable in providing very close predictions compared to other algorithms. SVR (RBF) training R2 obtained is 0.98 while all others were 0.9−0.... [more]

The proton exchange membrane fuel cell (PEMFC) is a favorable renewable energy source to overcome environmental pollution and save electricity. However, the mathematical model of the PEMFC contains some unknown parameters which have to be accurately estimated to build an accurate PEMFC model; this problem is known as the parameter estimation of PEMFC and belongs to the optimization problem. Although this problem belongs to the optimization problem, not all optimization algorithms are suitable to solve it because it is a nonlinear and complex problem. Therefore, in this paper, a new optimization algorithm known as the artificial gorilla troops optimizer (GTO), which simulates the collective intelligence of gorilla troops in nature, is adapted for estimating this problem. However, the GTO is suffering from local optima and low convergence speed problems, so a modification based on replacing its exploitation operator with a new one, relating the exploration and exploitation according to t... [more]

The Stirling engine is an alternative solution to produce cleaner energy in order to achieve the reduction of the fossil fuel consumption and the CO2 emissions. It comprises an external combustion engine that can convert any external heat source into mechanical power, through cyclic expansion and compression of a working gas in a closed-regenerative cycle, with or without driving mechanisms. The free-piston Stirling Engine is significantly preferred because of the absence of any mechanical linkage resulting in longer operating life, lower noise pollution, maintenance and vibration free, self-starting and high thermal efficiency. The aim of this paper is to summarize the research works on the free-piston Stirling engine technologies and models. First, the working principles of the free-piston Stirling engine are described, identifying different configurations. Then, several applications are presented. Finally, a detailed review of the models available in literature is given, pointing ou... [more]

The main purpose of this study is to investigate the relationships between key sources of air pollutant emissions (sources of energy production, factories which are particularly harmful to the environment, the fleets of cars, environmental protection expenditure) and the main environmental air pollution (SO2, NOx, CO and PM) in Poland. Models based on MLP neural networks were used as predictive models. Global sensitivity analysis was used to demonstrate the significant impact of individual network input variables on the output variable. To verify the effectiveness of the models created, the actual data were compared with the data obtained through modelling. Projected courses of changes in the variables under study correspond with the real data, which confirms that the proposed models generalize acquired knowledge well. The high MLP network quality parameters of 0.99−0.85 indicate that the network generalizes the acquired knowledge accurately. The sensitivity analysis for NOx, CO and PM... [more]

Intelligent integration of decentralised energy resources, local storage and direct consumption are key factors in achieving the transformation of the energy system. In this study, we present a modular simulation concept that allows the planning of decentralised energy systems for buildings and building blocks. In comparison to related studies, we use a simulation model for energy planning with a high time-resolution from the perspective of the energy system planner. In this study, we address the challenges of the grid connection in combination with an increasing number of electric vehicles (EV) in the future. The here developed model is applied for an innovative building block in Germany with a photovoltaic (PV) system, a combined heat and power (CHP) unit, battery storage and electric vehicles. The results of the simulation are validated with real-life data to illustrate the practical relevance and show that our simulation model is able to support the planning of decentralised energy... [more]

The limited reserves and well-known disadvantages of using fossil energy sources have increased the need for appropriate renewable substitutes in the production of various chemicals and materials. Biomass has been shown to be worthy of attention since it can be converted to biofuels and value-added chemicals relatively easily. The design of biomass valorisation process requires knowledge on the thermodynamic behaviour of the biomass-derived compounds, such as furfural and furfuryl alcohol. The thermodynamic and transport properties of the binary system furfural + furfuryl alcohol were studied at various temperatures and pressures. Density, speed of sound and refractive index were measured in the temperature range T = (288.15−345.15) K and viscosity was measured at temperatures up to 373.15 K, all at atmospheric pressure. Further, the density of pure components was obtained in the temperature range (293.15−413.15) K for furfural and (293.15−373.15) K for furfuryl alcohol at pressures up... [more]

The paper deals with issues of modeling nonlinear electrical loads of various types, such an uncontrolled rectifier, thyristor rectifier, thyristor power regulator and mixed equivalent nonlinear load. For these load types, existing analytical expressions were identified to determine the magnitudes of harmonic currents, and waveforms of currents were obtained during measurements in laboratory conditions with variable parameters of the grid impedance and load. The obtained results were compared, and it was found that the error in determining the magnitudes of harmonic currents can reach 60% for an individual load and 54% for an equivalent load. A more accurate method for determining the parameters of nonlinear electrical load is also proposed, which is based on the application of shunt harmonic filters. In laboratory conditions, it was found that when using the developed method, the error did not exceed 10% for an individual load and 14% for an equivalent load.

Partial discharge (PD) detection and analysis plays a crucial role for acceptance testing and condition monitoring of power cables. Various aspects are related to PD in power cables from theory to practice. This paper first summarizes the PD mechanism and models used for PD analysis in power cables. Afterwards, PD detection is addressed in the aspects of off-line test, on-line test, and sensors. PD analysis is discussed in detail. Specifically, related quantities and algorithms for PD analysis are outlined. PD characteristics with affecting factors, e.g., dielectric type, load, and applied voltage are discussed. Experience on PD development trend with measurements in field is analyzed. Based on the comprehensive review, challenges of PD detection and analysis along a power cable are proposed.

Carbon dioxide trans-critical refrigeration systems have been deeply investigated over the last years, with the aim to improve their performance by using several possible technical solutions. However, most of them lead to a more complex and expensive system, and therefore a trade-off is always needed to identify the best viable solution. Therefore, many efforts have also been focused on the study of a critical component of the basic carbon dioxide trans-critical cycle, which is the gas cooler, especially by numerical simulations. This work shows a new flexible approach to numerically model an air-cooled finned-tube CO2 trans-critical gas cooler integrating a Top-Down methodology with a Finite Difference Method to solve the governing equation of the thermodynamic processes involved. The model was developed to reproduce the behavior of an experimental CO2 refrigeration system, which provided the experimental data used for its validation. In detail, the model showed a good agreement with... [more]

Climate neutrality achievement in the European Union assumes the necessity of efforts and transformations in most economic sectors of its member-states. The farm sector in Poland, being the second largest contributor to the country’s greenhouse gas (GHG) emissions and in the top fifth of farm sectors in the EU-27 countries, needs to undergo structural and technological transformations to contribute to the climate action goals. The article assesses the potential impacts of Poland’s climate neutrality achievement path on the domestic farm sector in terms of its structure, output, income, and prices of agricultural products. The approach is based on complex economic modelling combining computable general equilibrium (CGE) and optimisation modelling, with the farm sector model consisting of farm, structural, and market modules. While the modelling results cover three GHG emission-reduction scenarios up to 2050, to understand the transformation impact within varying policy approaches, the s... [more]

Concentrating photovoltaic-thermal (CPVT) collectors have to face the challenge of contrary temperature requirements in the single receiver parts. The PV cells require low temperatures to achieve high efficiency, whereas the thermal part should generate high temperatures for providing industrial heat. The approach of “Spectral Splitting” can offer a solution for compact CPVT receivers; however, a clear quantification of the expected conversion efficiency is difficult. Therefore, this paper describes a modelling methodology for obtaining electrical and thermal performance parameters for a Spectral Splitting configuration using semiconductor-doped glass combined with appropriate heat transfer fluid. The PV technologies c-Si, CIGS and CdTe are considered. The presented model yields distinct results for maximising the electrical efficiency, calculates the reduction in waste heat dissipation within the cells and assesses the impacts of concentration factor and cell temperature. An optimised... [more]