Dried sphagnum moss was ground using a pin mill and a hammer mill under various operating conditions, i.e., changes in the rotor frequency and feed rate. The specific energy consumption of the size reduction was recorded. The ground powder was characterized by median particle size, width of size distribution (span), loose and tapped bulk densities, and the Hausner ratio. Pin milling used less energy for size reduction than hammer milling, especially when the target size was below 100 μm. In both milling methods, the specific energy consumption was mainly caused by the rotor frequency used. However, in pin milling, the specific energy consumption was also dependent on the production rate: the higher the rate, the higher the energy consumption. No such dependence was observed with the hammer mill. The span was wider in pin milling than hammer milling in the intermediate product size range although the difference decreased at the fine and coarse ends. A similar pattern was found for bulk... [more]

In recent years, photovoltaic energy has become a popular alternative to traditional fossil fuels due to its renewable and sustainable nature, and the incentives provided by countries to encourage research and development in this field have accelerated the implementation of photovoltaic roofs. One important factor in maximizing the efficiency of solar panels is their orientation to harness maximum irradiation with minimum roof area. In this article, an optimizer-supported east−west-oriented solar power plant installation is experimentally presented to utilize more solar energy with less area compared to wide-area south orientation. Furthermore, an analysis of different angle placements is simulated by PVSOL and PVGIS to test the robustness of the presented approach, and the pros/cons of the features of the east−west and south orientation are discussed comparatively. The obtained results are promising for the ideal placement of solar systems along with the use of optimizers to further e... [more]

In this paper, we analyze the role of economic policy in prompting energy efficiency. This study reviews three aspects, theoretical, empirical, and existing policies to evaluate the relationship of energy efficiency and economic policy. This study furthermore identifies the existing issues from a policy perspective in energy efficiency. Although not all public policies may be justified, it suggests that these types of financial incentives, particularly those based on economic instruments, can play a crucial role in advancing energy efficiency. Additionally, this study identifies existing issues in energy efficiency target achievement and proposes solutions based on the literature review. Finally, it provides possible future research pathways from the aspect of economic policy tools in energy efficiency.

Wireless Underground Sensor Networks (WUGSNs) transmit data collected from underground objects such as water substances, oil substances, soil contents, and others. In addition, the underground sensor nodes transmit the data to the surface nodes regarding underground irregularities, earthquake, landslides, military border surveillance, and other issues. The channel difficulties of WUGSNs create uncertain communication barriers. Recent research works have proposed different types of channel assessment techniques and security approaches. Moreover, the existing techniques are inadequate to learn the real-time channel attributes in order to build reactive data transmission models. The proposed system implements Deep Learning-based Multi-Channel Learning and Protection Model (DMCAP) using the optimal set of channel attribute classification techniques. The proposed model uses Multi-Channel Ensemble Model, Ensemble Multi-Layer Perceptron (EMLP) Classifiers, Nonlinear Channel Regression models... [more]

The decarbonisation of the building sector is crucial for Portugal’s goal of achieving economy-wide carbon neutrality by 2050. To mobilize communities towards energy efficiency measures, it is important to understand the primary drivers and barriers that must be overcome through policymaking. This paper aims to review existing Energy Policies and Actions (EPA) in Portugal and assess their effectiveness in improving Energy Efficiency (EE) and reducing CO2 emissions in the building sector. The Local Energy Planning Assistant (LEPA) tool was used to model, test, validate and compare the implementation of current and alternative EPAs in the North of Portugal, including the national EE plan. The results indicate that electrification of heating and cooling, EE measures, and the proliferation of Renewable Energy Sources (RES) are crucial for achieving climate neutrality. The study found that the modelling of alternative EPAs can be improved to reduce investment costs and increase Greenhouse G... [more]

In this study, modeling and thermodynamic analysis of the combined double flash geothermal cycle generation was conducted using zeotropic fluid as the working fluid in the Organic Rankine Cycle (ORC). The analysis was performed based on the first and second laws of thermodynamics. Hexane, cyclohexane, isohexane, R245fa, and R236ea exhibit good performance at higher temperatures. In this study, three fluids—hexane, cyclohexane, and isohexane—were used. First, the model results for the pure fluids were compared with those of previous studies. Then, the important parameters of the cycle, including the efficiency of the first law of thermodynamics, the efficiency of the second law of thermodynamics, net productive power, and the amount of exergy destruction caused by changing the mass fraction of the refrigerant for the zeotropic fluids (investigated for the whole cycle and ORC), were obtained and compared.

In Africa, switching to renewable energy sources with low carbon emissions is becoming more popular. In the Economic Community of West African states (ECOWAS), the low-carbon energy transition must overcome significant obstacles, including those posed by policies put in place and their implementation. In order to replace the current fossil fuel-driven economy with low-carbon development that also advances the regional aims and Sustainable Development Goals (SDGs), this paper analyzes the current policy landscape in the region. A total of 75 policies from four categories (energy access, energy efficiency, renewable energy, climate change) were chosen for the policy review. Multicriteria decision analysis and a thorough review of the literature have shed light on how well the policies of the ECOWAS countries could promote low-carbon development and what the main challenges to overcome are. The last step was the comparison of the progress of the two key policies in the region: the Nationa... [more]

Selected structures intended to absorb impact energy have been analysed in respect of their use in the rear underrun protective devices (RUPD) of motor trucks. The main purpose of the RUPD is to prevent a passenger car from running under the rear of a motor truck provided with such a device. From the point of view of the safety of the car occupants, it is important to take into account the components whose additional role would be to absorb a part of the impact energy so that the loads on the said occupants were minimised. This article presents experimental test results concerning selected energy-absorbing structures. Based on quasi-static strength tests, simplified material models were defined. As a result of experimental crash tests, the possible applications of selected energy absorbers to the RUPDs as their components accountable for the passive safety of passenger cars were indicated. Absorbers proposed in this paper can be considered effective energy-absorbing structures, e.g., i... [more]

Energy efficiency programs funded by utility customers provide an electricity resource in most U.S. states, but their scale and cost of saving electricity varies significantly by state. In this paper, we explore the drivers of the cost of saved electricity in these programs with an econometric model and nearly a decade of data reported by efficiency program administrators. We found strong evidence for economies of scale and weak evidence for diseconomies of scale, which suggests that states with low levels of efficiency savings relative to retail sales can increase the size of their efficiency programs without large increases to the cost of saved electricity. We discuss examples of energy efficiency forecasting and potential modeling in light our econometric analysis and identify methodological improvements relevant to utilities and grid operators. This paper provides insights into the economics of customer-funded efficiency programs that will support regulators, utilities, and policym... [more]

The current socio-economic and environmental context obliges companies to increase their energy efficiency to be competitive, and the development of Industry 4.0 technologies should contribute to improve it. This article analyses the influence of Industry 4.0 technologies on energy efficiency and the mediation of quality management of production process variables. After a descriptive analysis, a correlation and regression analysis is presented using information from 72 projects for the integration of Industry 4.0 technologies in industrial companies. At a global level, it is confirmed that the four technology groups (Artificial Vision and Artificial Intelligence, Additive Manufacturing and Robotics, Big Data and Advanced Analytics, and Internet of Things) contribute to improving energy efficiency by an average of 15−25% in the processes where they are integrated. In addition, the regression model determines that improved decision-making capabilities strongly mediate the achievement of... [more]

Worldwide, the design, renovation, and sustainable management of port buildings play a crucial role for sustainability. In this framework, a computer simulation of a building’s thermal behaviour is an almost mandatory tool for making informed decisions. However, the development of a building energy model is a challenging task that could discourage its adoption. A possible solution would be to exploit an existing Building Information Modeling (BIM) model to automatically generate an accurate and flexible Building Energy Modeling (BEM) one. Such a method, which can substantially improve decision-making processes, still presents some issues and needs to be further investigated, as also detectable from the literature on the topic. In this framework, a novel workflow to extrapolate BIM data for energy simulation is proposed and analysed in this paper. Here, the BIM to BEM approach was tested as a useful tool for the maritime industry to improve the implementation of effective energy-saving... [more]

The study targeted towards drying of cantaloupe slices with various thicknesses in a microwave dryer. The experiments were carried out at three microwave powers of 180, 360, and 540 W and three thicknesses of 2, 4, and 6 mm for cantaloupe drying, and the weight variations were determined. Artificial neural networks (ANN) and adaptive neuro-fuzzy inference systems (ANFIS) were exploited to investigate energy and exergy indices of cantaloupe drying using various afore-mentioned input parameters. The results indicated that a rise in microwave power and a decline in sample thickness can significantly decrease the specific energy consumption (SEC), energy loss, exergy loss, and improvement potential (probability level of 5%). The mean SEC, energy efficiency, energy loss, thermal efficiency, dryer efficiency, exergy efficiency, exergy loss, improvement potential, and sustainability index ranged in 10.48−25.92 MJ/kg water, 16.11−47.24%, 2.65−11.24 MJ/kg water, 7.02−36.46%, 12.36−42.70%, 11.25... [more]

Based on the development of the theory of reactive power and distortion power, starting with the works of Fryze and Budeanu, it has been found that the contradictions in the definition of the components of inactive powers are caused by errors in the introduced intermediate concepts and corresponding calculations when switching to nonlinear and non-sinusoidal AC circuits. The materials of the works of modern researchers and the numerical calculations carried out made it possible to trace the differences between reactive power and distortion power, to confirm the orthogonality properties of the active, reactive power, and distortion power components. The paper defines the conditions for achieving a power balance in an AC network with nonlinear loads, compiled and tested criteria leading to the absence of distortion power in a single-phase AC network. Using the time base of the projection of the generalized vectors in vector diagrams, it is shown that compliance with the criteria for the... [more]

Increasing the energy efficiency of machining operations can contribute to more sustainable manufacturing. Therefore, there is a necessity to investigate, evaluate, and optimize the energy consumed during machining operations. The research highlights a method employed to prioritize the most energy-intensive machining operation and highlights the significance of electric parameters as predictors in power estimation of machining operations. Multi regression modeling with standardized regression weights was used to identify significant power quality predictors for active power evaluation for machining operations. The absolute error and the relative error both decreased when the active power was measured by the power analyzer for each of the identified machining operations, compared to the standard power equation and that obtained from the modeled regression equations. Furthermore, to determine energy-intensive machining operation, a hybrid decision-making technique based on TOPSIS (a tech... [more]

Humanity is dependent on natural resources. Use and productivity of these resources plays an important role in energy savings and circular economy. The goal of this contribution is to evaluate productivity of resources in the frame of EU countries. Single analysis deals with data from the publicly available portal database and collected data were processed in the statistical software JMP. The trend of development and analysis of variability and linear dependence helped to create cluster analysis and comparison of the EU countries. The results from the view of average value of the indicator registered the growth, and from the view of variability the statistically important differences were verified for EU member states. Some pairs of indicators recorded positive, while some pairs recorded negative linear dependence. Cluster analysis shows two groups of countries—the first one with positive results, having the lowest tax burden in the case of energy taxes and environment, and the second... [more]

The implementation of monitoring tools and energy management systems (EnMSs) supports companies in their long-term energy efficiency strategies, and they are essential to analyse the effectiveness of energy performance improvement actions (EPIAs). The first fundamental step towards increasing energy efficiency is the development of energy audits (EAs). EAs provide comprehensive information about the energy usage in a specific facility, identifying and quantifying cost-effective EPIAs. The crucial role of these tools in clean energy transition is remarked by the European Energy Efficiency Directive (EED), which promotes the implementation of EAs and EnMS programmes. The purpose of this work is to better understand the link between EnMSs (specifically ISO 50001) and EAs in the EED Article 8 implementation in two industrial and two tertiary sectors in Italy. Moreover, the impact of company size, energy monitoring systems, and EnMSs on planned and/or implemented EPIAs is analysed. Our find... [more]

Integrating data analytics, optimisation and dynamic control to support energy services has seen significant interest in recent years. Larger appliances used in an industry context are now provided with Internet of Things (IoT)-based interfaces that can be remotely monitored, with some also provided with actuation interfaces. The combined use of IoT and edge computing enables connectivity between energy systems and infrastructure, providing the means to implement both energy efficiency/optimisation and cost reduction strategies. We investigate the economic implications of harnessing IoT and edge/cloud technologies to support energy management for HVAC (Heating, Ventilation and Air Conditioning) systems in buildings. In particular, we evaluate the cost savings for building operations through energy optimisation. We use a real use case for energy optimisation as identified in the EU “Sporte2” project (focusing on the energy optimisation of sports facilities) and explore several scenarios... [more]

Energy efficiency is a huge opportunity for both the developed and the developing world, and ICT will be the key enabler towards realising this challenge, in a huge variety of ways across the full range of industries. In the telecommunications space in particular, power consumption and the resulting energy-related pollution are becoming major operational and economical concerns. The exponential increases in network traffic and the number of connected devices both make energy efficiency an increasingly important concern for the mobile networks of the (near) future. More specifically, as 5G is being deployed at a time when energy efficiency appears as a significant matter for the network ability to take into account and to serve societal and environmental issues, this can play a major role in helping industries to achieve sustainability goals. Within this scope, energy efficiency has recently gained its own role as a performance measure and design constraint for 5G communication networks... [more]

The built environment is the global sector with the greatest energy use and greenhouse gas emissions. As a result, building energy savings can make a major contribution to tackling the current energy and climate change crises. Fluid dynamics models have long supported the understanding and optimization of building energy systems and have been responsible for many important technological breakthroughs. As Covid-19 is continuing to spread around the world, fluid dynamics models are proving to be more essential than ever for exploring airborne transmission of the coronavirus indoors in order to develop energy-efficient and healthy ventilation actions against Covid-19 risks. The purpose of this paper is to review the most important and influential fluid dynamics models that have contributed to improving building energy efficiency. A detailed, yet understandable description of each model’s background, physical setup, and equations is provided. The main ingredients, theoretical interpretatio... [more]

This paper presents a scientific development aimed at improving the efficiency of turbomachines through the joint use of rotary-vane and vortex workflows. In the well-known Euler turbine, the rotor flow channels represent a set of curved pipes. The authors propose to consider in more detail the possibilities of using such rotating pipes in the implementation of an ejection (vortex) workflow. A hybrid pump was considered with the conclusion that its workflow can be described using two Euler equations. The results of computer simulation indicate that hybrid turbomachines are promising. The use of additive technology allowed the creation of micromodels of the Euler turbine with various rotor designs. Laboratory hydraulic tests showed that the liquid inlet to the rotor is possible in pulse mode. Laboratory tests of micromodels using compressed air showed that gas (or liquid) motion through curved pipes could be carried out from the rotor periphery to its center and then back, albeit throug... [more]

This paper presents a method for evaluating the energy efficiency of pump systems used to transport fluids .It is mainly scientifically applied and engineering-applied in nature and aims to propose a new approach (method) to researchers in their study of the energy efficiency of such systems. By applying the well-known scientific method of Dimensional Analysis (Buckingham π-theorem), dimensionless complexes (π-criterions and their relevant equations, which are original (innovative) and are offered for the first time in the scientific literature), used in accomplishing an energy assessment and analysis of such systems, are obtained. The criterion ∏1 = ev/ρgD represents specific energy consumption in kWh/m3 for a given pipe system with an exemplary diameter D. The criterion ∏2 = Q/[n(Hp − Hst)D2] represents a generalized parameter which is characterized by the selected method of flow rate (Q) regulation for a pump system with given static head Hst—by changing the speed of rotation (VFD,... [more]

To solve the contradiction between achieving long-term economic growth and reducing the consumption of certain types of resources, the concept of sustainable resource saving economic development must be put into practice. The purpose of this research is to establish criteria, develop indicators, and identify factors of the sustainable energy-saving economic development, as well as to test the developed theoretical provisions using the example of natural gas consumption by different countries. To achieve this goal, various methods were used, including economic and mathematical modeling, time series analysis, factor analysis, regression analysis, and so on. The criteria were formalized, according to which a certain type of economic development can be attributed to energy saving both at the level of the state economy as a whole and at the level of individual industries and enterprises. It was established that the formalized criteria of the sustainable energy-saving economic development ha... [more]

Environmental pollution, energy supply and security of supply have become major issues across the world due to climate change, limited energy sources, energy price volatility and energy supply constraints. Energy availability, energy efficiency and the replacement of fossil fuels by renewable energy sources are key factors in the global development of sustainable energy. In many countries with limited fossil fuel resources, the sustainable development of renewable energy sources is an important tool in reducing dependence on imported fuels. Some alternative energy sources, such as wind, solar, tidal and hydropower, seem almost inexhaustible. With the exception of tidal energy, all of these sources have been used extensively and for a long time. This article examines the improvement of energy security and the government’s actions to promote the use of renewable energy sources, focusing on increasing energy efficiency and reducing energy intensity and dependence on energy imports in Lith... [more]

This paper proposes methodological approaches to assessing the impact of renewable energy and energy efficiency development on emerging economies’ energy security. It is suggested to supplement the current methodology for assessing energy security with the decoupling index of the renewable energy financial burden on the state budget, the energy efficiency decoupling index, the households’ energy poverty indicator, the index of capacity development for balancing electricity generation volumes, and the energy fluctuations indicator. These indices provide a comprehensive assessment of energy security under the latest challenges. Thus, the COVID-19 pandemic in the Ukrainian energy sector led to the “green and coal paradox”, when the government decided to keep green electricity generation but limit nuclear generation. It required increased flexible capacities (thermal generation) and led to a rise in electricity prices and environmental pollution. Forecasting energy fluctuations with Butter... [more]

In the last decade, China has sharply tightened the monitoring values for wastewater treatment plants (WWTPs). In some regions with sensitive discharge water bodies, the values (24 h composite sample) must be 1.5 mg/L for NH4-N and 10 mg/L for total nitrogen since 2021. Even with the previously less strict monitoring values, around 50% of the wastewater treatment plants in China were permanently unable to comply with the nitrogen monitoring values. Due to the rapid changes on-site to meet the threshold values and the strong relation to energy-intensive aeration strategies to sufficiently remove nitrogen, WWTPs do not always work energy-efficiently. A Chinese WWTP (450,000 Population equivalents or PE) with upstream denitrification, a tertiary treatment stage for phosphorus removal and disinfection, and aerobic sludge stabilisation was modelled in order to test various concepts for operation optimisation to lower energy consumption while meeting and undercutting effluent requirements. F... [more]