In a planet with limited resources, climate change is a severe problem, intensified by industrial development. This is particularly important in the construction sector. According to the International Energy Agency (2021), the construction sector is responsible for 40% of the global energy consumption and 36% of CO2 emissions. In this way, sustainable architectural solutions should be a priority in our fight against climate change, for it is necessary to propose solutions that help to reuse existing resources, thus reducing consumption. In this sense, the rehabilitation of buildings with solutions that favor the circular economy will become a key element in the construction sector. This work provides the design of a facade for building rehabilitation based on the circular economy paradigm, which is implanted in a model building as a case study. The HULC tool quantifies the improvement in energy efficiency that this rehabilitation entails when compared to a conventional facade. With the... [more]

In our research, we analyzed the energy and water consumption in diamond mining and laboratory synthesis operations. We used publicly available reports issued by two market leaders, DeBeers and ALROSA, to estimate water and energy use per carat of a rough diamond. The efficiency of the two most popular synthesis technologies for artificial diamonds—High-Pressure-High-Temperature (HPHT) and Microwave-assisted Chemical Vapor Deposition (M-CVD)—was examined. We found that the modern HPHT presses, with open cooling circuits, consume about 36 kWh/ct when producing gem-quality and average-sized (near-) colorless diamonds. ALROSA and DeBeers use about 96 kWh/ct and 150 kWh/ct, respectively, including all energy required to mine. Energy consumption of M-CVD processes can be different and depends on technological conditions. Our M-CVD machine is the least energy-efficient, requiring about 215 kWh/ct in the single-crystal regime, using 2.45-GHz magnetron for the support synthesis. The M-CVD meth... [more]

A daylighting control system that uses the closed loop proportional algorithm needs to be calibrated both during nighttime and daytime. The selection of the daytime calibration time can affect the behavior of the system and is usually performed when the ratio of the illuminance of the ceiling sensor (SD) to the illuminance at a point on the working plane (ED) is relatively large without sunlight patches in the ceiling photo-sensor’s field of view (FOV). However, this requirement is not associated with a specific value and can be achieved under a wide range of conditions related to the sky luminance distribution. In the present work, four ceiling sensors with different field of views (FOVs) were examined in a typical north-facing office space. The effect of daytime calibration on the system’s performance was estimated through the calculation of lighting energy savings and the overdimming percentage. The results show that the effect of both the FOV of the ceiling sensor and the daytime c... [more]

The aim of the study is to explore the intellectual structure of the field and fronts in research on energy efficiency in the context of cloud computing and thus to contribute to science mapping of the research field. The research process was driven by the following study questions: (1) what are the most influential publications in the research field? and (2) what are the research fronts in the research field? The method of direct citation analysis was employed in the research process. Data for analysis were obtained from the Scopus database and analyzed with the use of VOSviewer science mapping software. In response to the first question, we identified the most influential publications in the research field and analyzed their types (i.e., whether they are original research papers or rather the “context” papers e.g., survey or review papers, framework papers, challenges papers, and study papers). Moreover, a comparison analysis between the types of papers among the most cited “classica... [more]

Energy efficiency (EE) is of great concern in cognitive radio networks since the throughput and energy consumption of secondary users (SUs) vary with the sensing time. However, the conditions of the detection probability and false alarm probability should be respected to better protect primary users (PUs) and to improve the sensing performance of SUs. Additionally, the PUs’ minimum averaged power provision should also be regarded as a key problem of interactive linking to SUs. Therefore, an integrated design between the PU and SUs is desired for the coordination of the whole cognitive radio system, especially regarding the satisfaction of EE and performance metrics. This study formulates sensing constraints in a unified way and calculates the minimum SNR of SUs, based on which the essential PU power provision is computed. Furthermore, EE is proved as a decreasing function with the PU’s active ratio, where the maximum EE is obtained corresponding to the minimum QoS requirements of the s... [more]

Passivhaus EnerPHit is a rigorous retrofit energy standard for buildings, based on high thermal insulation and airtightness levels, which aims to significantly reduce building energy consumption during operation. However, extra retrofit materials are required to achieve this standard, which raises a contradiction between how to balance the environmental impacts of the retrofitting material inputs and extremely low energy consumption after retrofit. This motivated the analysis in this paper, which aimed to evaluate the possibilities of reducing the required retrofitting material inputs when trying to achieve the EnerPHit energy standard using a typical suburban dwelling in China’s hot summer−cold winter climate region as a case study. Firstly, how the insulation performance of each envelope component affected the building’s energy consumption was analysed. Based on this, sensitivity simulations of combinations of different insulation levels with different fabric components were investig... [more]

The definition of multiple slicing types in 5G has created a wide field for service innovation in communications. However, the advantages that network slicing has to offer remain to be fully exploited by today’s applications and users. An important area that can potentially benefit from 5G slicing is emergency communications for First Responders. The latter consists of heterogeneous teams, imposing different requirements on the connectivity network. In this paper, the RESPOND-A platform is presented, which provides First Responders with network-enabled tools on top of 5G on-scene planning, with enhanced service slicing capabilities tailored to emergency communications. Furthermore, a mapping of emergency services and communications to specific slice types is proposed to identify the current challenges in the field. Additionally, the proposed tentative mechanism is evaluated in terms of energy efficiency. Finally, the approach is summarized by discussing future steps in the convergence... [more]

Energy is crucial to economic development, but its production usually has a negative impact on the environment. This ambivalence leads to the need for methods to improve energy efficiency. Transportation is one of the largest global energy consumers. Therefore, improving the energy efficiency of transportation is crucial for sustainable development. The aim of this article is to show the limitations of energy management in railways, resulting from the model of market regulation. The question in this context is whether only technological methods can be used in railways to steer its energy efficiency, as is suggested by the existing research. Critical analysis, desk research and a case study of Polish railway undertaking were used to find an answer to the research question. The discussion of the results shows that the European regulatory system leads to greater complications in the field of energy management than in other global regions, where railways are also important for the economy.... [more]

The European Union has set an ambitious goal to tackle climate change, and energy efficiency in the residential sector is among the measures required to close the gap between targeted and actual greenhouse gas emissions. While different policy tools have been applied, the diffusion rate of these measures remains low. A system dynamics simulation model of the residential sector was developed to assess the advantages and drawbacks of energy efficiency policy in the multi-family building sector based on experience accumulated over the last twelve years in Latvia. The model was validated in expert group model building sessions and with historical trends. Simulating the model, a hypothesis was tested that supported the idea that seemingly positive policy tools set the stage for a series of unintended adverse effects due to the complex interactions between different system components. The common assumption that information and financial support should result in significant energy efficiency... [more]

District heating (DH) is an alternative technology to Individual Heating (IH) for satisfying end-user’s needs. This paper assesses the competitiveness of a DH network in the center of Italy from energy, environmental, and economic points of view considering both thermal power plant and end-users’ sides. On the thermal power plant side, the energy analysis considers the Primary Energy Saving (PES) and the specific energy (Esp) of the fuel actually exploited in the thermal power plant compared to its Low Heating Value (LHV), while the environmental analysis considers the avoided CO2 and the economic analysis considers the Energy Efficiency Certificates (EECs). Results showed that the current thermal power plant configuration with two boilers and a Combined Heat and Power (CHP) unit reaches a yearly PES of 21.3% as well as 1099 tCO2 avoided. From the economic analysis of the thermal power plant side, 829 EECs with an economic return of 207,222€ are obtained, while from the end-users’ side... [more]

The 2030 Climate target plan of the European Commission (EC) establishes a greenhouse gases (GHG) emissions reduction target of at least 55% by 2030, compared to 1990. It highlights that all transport modes—road, rail, aviation and waterborne—will have to contribute to this aim. A smart combination of vehicle/vessel/aircraft efficiency improvements, as well as fuel mix changes, are among the measures that can reduce GHG emissions, reducing at the same time noise pollution and improving air quality. This research provides a comprehensive analysis of recent research and innovation in low-emission alternative energy for transport (excluding hydrogen) in selected European Union (EU)-funded projects. It considers the latest developments in the field, identifying relevant researched technologies by fuel type and their development phase. The results show that liquefied natural gas (LNG) refueling stations, followed by biofuels for road transport and alternative aviation fuels, are among the r... [more]

This study analyses the Ukrainian energy system in the context of the Paris Agreement and the need for the world to limit global warming to 1.5 °C. Despite ~84% of greenhouse gas emissions in Ukraine being energy- and process-related, there is very limited academic literature analysing long-term development of the Ukrainian energy system. This study utilises the TIMES-Ukraine model of the whole Ukrainian energy system to address this knowledge gap and to analyse how the energy system may develop until 2050, taking into current and future policies. The results show the development of the Ukrainian energy system based on energy efficiency improvements, electrification and renewable energy. The share of renewables in electricity production is predicted to reach between 45% and 57% in 2050 in the main scenarios with moderate emission reduction ambitions and ~80% in the ambitious alternative scenarios. The cost-optimal solution includes reduction of space heating demand in buildings by 20%... [more]

Transport is one of the key sectors of the European economy. However, the intensive development of transport caused negative effects in the form of an increase in the emission of harmful substances. The particularly dramatic situation took place in the V4 countries. This made it necessary to implement solutions reducing emissions in transport, including passenger transport. Such activities can be implemented in the field of implementation of low-emission and zero-emission vehicles for use. That is why the European Union and the governments of the Visegrad Group countries have developed numerous recommendations, communications, laws, and strategies that order carriers to implement low- and zero-emission mobility. Therefore, transport organizers and communication operators faced the choice of the type of buses. From an economic point of view, each entrepreneur is guided by the economic efficiency of the vehicles used. Hence, the main aim of the article was to conduct an economic evaluati... [more]

Data centres are a key infrastructure for the global digital economy, helping enable the EU “Digital Decade” by 2030. In 2015, data centres were estimated to consume 2.5% of EU electricity demand. In Ireland, the concentrated presence of data centres could consume 37% of national electricity demand by 2028. The uncertainty of data centre facility-level energy efficiency paired with the need to achieve a low-carbon economy pose significant challenge for generation and transmission network planning. This is the first paper to apply a model of technology diffusion with a national forecast of changes in Irish data centre electricity demand through more efficient liquid cooling. The methodology serves as a technology-agnostic resource for practitioners performing forecasts under uncertainty with limited information. Results suggest that technology adoption could lower national electricity demand by 0.81% if adopted by new plant from 2019 to 2028. Savings rise to 3.16% over the same period i... [more]

Industry 4.0 challenges facilities entrepreneurs to be competitive in the market in terms of energy by rational decision making. The goal of the paper is aimed at introducing Prospect Theory (PT) in Industry 4.0 for making decisions in order to select an optimal energy technology. To reach this goal, an approach for decision making on energy investment has been developed. In this paper, the authors have also provided a new opportunity to apply the new decision making method for strengthening Industry 4.0 by addressing energy concerns based on which rational decisions have been made. The study uses a fuzzy analytical hierarchy process for weighting the evaluation sub-criteria of energy technologies and a modified PT for making decisions related to the selection of one of the investigated technologies. The results show that it is possible to implement PT in Industry 4.0 via a decision making model for energy sustainability. Decision probability was achieved using a behavioral approach ak... [more]

Harmful emissions from heating installations have recently received public attention in Poland. Polish municipalities mainly take their heat from local district heating networks with large-scale coal-fired heat sources. Today, transition to nonemissive sources on this scale would be impractical. The easiest way to reduce carbon emissions is to limit heat consumption, but at the same time, to preserve thermal comfort, the application of smart technologies is necessary. Veolia operates on 71 district heating systems in Poland, including Warsaw, Lodz, and Poznan. Since heat consumption in Warsaw and Metropolis GZM is at a similar level, this is a case study of Hubgrade automation system application within the Warsaw district heating network. This paper also presents results of simulation of harmful emission reduction potential in Metropolis GZM. Simulation results show that there is a potential for saving approximately 275 kt of CO2 for the whole Metropolis GZM.

Meeting the Paris Agreement on climate change requires substantial investments in low-emissions energy and significant improvements in end-use energy efficiency. These measures can also deliver improved air quality and there is broad recognition of the health benefits of decarbonising energy. Monetising these health benefits is an important part of a robust assessment of the costs and benefits of renewable energy and energy efficiency programs (clean energy programs (CEP)) and a variety of methods have been used to estimate health benefits at national, regional, continental and global scales. Approaches, such as unit damage cost estimates and impact pathways, differ in complexity and spatial coverage and can deliver different estimates for air pollution costs/benefits. To date, the monetised health benefits of CEP in Australia have applied international and global estimates that can range from 2−229USD/tCO2 (USD 2016). Here, we calculate the current health damage costs of coal-fired po... [more]

All the urban areas of developed countries have hydric distribution grids and sewage systems for collecting municipal wastewater to treatment plants. In this way, the municipal wastewater is purified from human excreta and other minor contaminants while producing excess sludges and purified water. In arid and semi-arid areas of the world, the purified water can be used, before discharging, to enhance the energy efficiency of seawater desalination and solve the problems of marine pollution created by desalination plants. Over the past half-century, seawater desalination has gradually met demand in urbanized, oil-rich, arid areas. At the same time, technological evolution has made it possible to significantly increase the energy efficiency of the plants and reduce the unit cost of the produced water. However, for some years, these trends have flattened out. The purified water passes through the hybridized desalination plant and produces renewable osmotic energy before the final discharge... [more]

Next-generation power systems aim at optimizing the energy consumption of household appliances by utilising computationally intelligent techniques, referred to as load monitoring. Non-intrusive load monitoring (NILM) is considered to be one of the most cost-effective methods for load classification. The objective is to segregate the energy consumption of individual appliances from their aggregated energy consumption. The extracted energy consumption of individual devices can then be used to achieve demand-side management and energy saving through optimal load management strategies. Machine learning (ML) has been popularly used to solve many complex problems including NILM. With the availability of the energy consumption datasets, various ML algorithms have been effectively trained and tested. However, most of the current methodologies for NILM employ neural networks only for a limited operational output level of appliances and their combinations (i.e., only for a small number of classe... [more]

This paper presents an innovative technique of traffic management on a route divided into fixed block distances for trains equipped with a continuous area data transmission system that ensures information exchange between a train and a control center. The originality of the technique is focused on the optimization of the following train’s speed profile in terms of energy consumption under the need to maintain a minimum distance to the preceding train and to assume the smooth running of the following train, using elements of fixed and mobile block distance methods. The obtained results are an answer to the question of whether it is possible to obtain a smoother movement of the train and savings in mechanical energy consumption if the speed profile of this train is adjusted to the conditions before the train, such as information about the speed of the preceding train.

Deployment of CTA-2045−enabled devices is increasing in the U.S. market. These devices allow utilities or third-party aggregators to control appliance energy use in homes, and could also be applied to end uses in small commercial buildings. This study focuses on a field study using CTA-2045−enabled water heaters to shift electric load off the peak and toward periods when renewable resources are more prevalent (e.g., near noon for solar resources and near midnight for wind resources). The following load shifting strategies were compared to understand effects on the aggregate load-shifting capabilities of Heat Pump Water Heaters (HPWHs) and on consumer hot water supply: non-targeted (traditional), targeted (grouped, with different shifting schedules) and “smart” (adaptive control commands). The results of this study show that targeted and smart control strategies yield significantly more load-shifting potential from a population of water heaters than the non-targeted approach without sac... [more]

The flyback converter has been widely used in Photovoltaic microinverters, operating either in Discontinuous, Boundary, or Continuous Conduction Mode (DCM, BCM, CCM). The recently proposed hybrid DBCM operation inherits the merits of both DCM and BCM. In this work, the necessary analytical equations describing the converter operation for any given condition under DBCM are derived, and are needed due to the hybrid nature of the modulation strategy during each sinusoidal wave. Based on this analysis, a design optimization sequence used to maximize the weighted efficiency of the inverter under DBCM is then applied. The design procedure is based on a power loss analysis for each converter component and focuses on the appropriate selection of the converter parameters. To achieve this, accurate, fully parameterized loss models of the converter components are implemented. The power loss analysis is then validated by applying the optimization methodology to build an experimental prototype oper... [more]

Energy-efficient building retrofits must be approached from three perspectives: law regulation approach, financial incentives approach, and practice approach. The concepts of zero energy building and life cycle energy building are presented as the basis for energy retrofits. Multi-criteria boards to assess the decision-making process are reviewed, analysed, and categorised under an architectonic perspective. Some examples are presented, with different packages of measures, from deep to non-invasive energy retrofits. Passive and active energy generation systems, together with control and management strategies, are the physical elements identified with the potential to improve buildings’ energy efficiency. From a practice approach, this literature review identifies the concept of performance-based architectural design to optimise the planning and design of buildings’ energy retrofits. In addition, tools such as Building Information Modelling are described as part of optimisation processe... [more]

We examine the energy use impacts of energy efficiency and solar PV projects financed by residential property assessed clean energy (R-PACE) programs in California. We leverage household-level interval meter data to apply normalized metered energy consumption (NMEC) methods at significant scale—more than 25,000 electric meters and more than 15,000 gas meters. We develop a comparison group to account for non-project-related changes in usage. The projects include homes that replaced existing HVAC equipment with higher-efficiency units and homes that installed central heating or air conditioning equipment for the first time. We have limited information on pre-project household equipment stock so we develop a method to infer new installations. We find that projects that installed energy efficiency technologies reduce electricity consumption by approximately 3% and gas consumption by approximately 3.5% on average. When we remove homes that installed new cooling and heating equipment for the... [more]

Nowadays, microgrids (MGs) play a crucial role in modern power systems due to possibility of integrating renewable energies into grid-connected or islanded power systems. The Load Frequency Control (LFC) is an issue of paramount importance to ensure MGs reliable and safe operation. Specifically, in AC MGs, primary frequency control of each energy source can be guaranteed in order to integrate other energy sources. This paper proposes a micro-hydro frequency control scheme, combining the control of a reduced dump load and the nozzle flow control of Pelton turbines operating in autonomous regime. Some works have reported the integration of dump load and flow control methods, but they did not reduce the dump load value and adjust the nozzle flow linearly to the power value demanded by users, causing the inefficient use of water. Simulation results were obtained in Matlab®/Simulink® using models obtained from previous research and proven by means of experimental studies. The simulation of... [more]