In order to investigate the grid integration of wind turbines (WT) of various scales and designs, a wind turbine emulator (WTE) is being built in Flensburg within the state-funded project GrinSH. The special feature of this WTE is the use of a large gas engine instead of an electric motor to emulate the behavior of a WT. In order to develop the controls of this innovative WTE and to design the upcoming test runs under safe conditions, a software in the loop model (SILM) was applied. This SILM contained a mathematical model of the wind turbine, mathematical models of the gas engine with an integrated controller, and a model of the generator and frequency converter unit, as well as a preventive modulator of the reference signal (PMRS). The PMRS module converts the reference signal of the emulated WT in such a way that the dynamics of the engine components can be calculated and balanced in advance to enable the required behavior of the entire SILM despite the dynamics of the gas engine. I... [more]

Assessing the potential of advanced driver assistance systems requires developing dedicated control algorithms for controlling the longitudinal speed of automated vehicles over time. In this paper, a multiobjective off-line optimal control approach for planning the speed of the following vehicle in adaptive cruise control (ACC) driving is proposed. The implemented method relies on the principle of global optimality fostered by dynamic programming (DP) and aims to minimize propelling energy consumption and enhance passenger comfort. The powertrain model and onboard control system are integrated within the proposed car-following optimization framework. The retained ACC approach ensures that the distance between the following vehicle and the preceding vehicle is always maintained within allowed limits. The flexibility of the proposed method is demonstrated here through ease of implementation on a wide range of powertrain categories, including a conventional vehicle propelled by an interna... [more]

Bipolar lightning strokes are associated with multiple polarity electrical discharge with no current intervals in between, making their behavior quite peculiar. This work presents a fast front analysis of a mixed high voltage direct current (HVDC) transmission link, evaluating the factors that influence the line transients due to shielding failures and backflashovers (BFOs), considering both overvoltage and repeated polarity reversal at the cable sending terminal. The research process includes a detailed modeling of a bipolar lightning stroke, frequency-dependent HVDC overhead, and underground transmission line sections. Noticeable findings include the occurrence of only a positive polarity insulator BFO for the adjacent and subsequent tower, despite the dual polarity of the lightning stroke with relatively small values for the lightning parameters. The influence of traveling waves on the insulator flashover performance of the line with varying parameters (such as the riser section len... [more]

Offshore wind power plants are becoming a realistic option for the renewable production of electricity. As an improvement tool to the profitability of OWFs, this work presents the first complete non-genetic (and non-binary) evolutionary algorithm to optimize the location, size and layout of a parallelogram-shaped offshore wind farm, as the arrangement that is becoming an standard for offshore wind farms. It has been tested in the HRI site. Most relevant economic data influencing the investment profitability have been taken into account. In addition, the paper introduces a new approach to offshore wind farm optimization based on a continuous behaviour of varying wind conditions, which allows a more realistic estimation of the energy produced. The proposed optimization approach has been tested based on the available information from HRI. Obtained solutions present similar values to the actual offshore wind farm in terms of investment and annual energy produced, but differs with respect t... [more]

Dry reforming of hydrocarbons, alcohols, and biological compounds is one of the most promising and effective avenues to increase hydrogen (H2) production. Catalytic dry reforming is used to facilitate the reforming process. The most popular catalysts for dry reforming are Ni-based catalysts. Due to their inactivation at high temperatures, these catalysts need to use metal supports, which have received special attention from researchers in recent years. Due to the existence of a wide range of metal supports and the need for accurate detection of higher H2 production, in this study, a systematic review and meta-analysis using ANNs were conducted to assess the hydrogen production by various catalysts in the dry reforming process. The Scopus, Embase, and Web of Science databases were investigated to retrieve the related articles from 1 January 2000 until 20 January 2021. Forty-seven articles containing 100 studies were included. To determine optimal models for three target factors (hydroca... [more]

The meteorological environment is a determining factor in photovoltaic (PV) system feasibility (PVSF). To evaluate this impact more accurately, a quantitative analysis model based on multimeteorological factors and the Random Forest Regression model is proposed in this work. Firstly, an evaluation system is established to assess the impact. Then, to predict the indicators of the evaluation system, a parameter, i.e., performance ratio in sampling period, is defined. Secondly, a set of essential influences on the performance ratio in the sampling period is established through analyzing and reducing the discovered influences on the PV system performance. Finally, data from the Desert Knowledge Australia Solar Centre (DKASC) website are used to conduct the experiment. During the experiment, the sample set is cleaned using the model based on the cosine of the zenith angle. The functional relationship between the performance ratio in the sampling period and its essential influences is establ... [more]

In this numerical study, 4 types of hybrid nanofluid, including Ag-MgO/water, TiO2-Cu/water, Al2O3-CuO/water, and Fe3O4-multi-wall carbon nanotube/water, have been considered potential working fluid in a single U-tube borehole heat exchanger. The selected hybrid nanofluid is then analyzed by changing the volume fraction and the Reynolds number. Based on the numerical results, Ag-MgO/water hybrid nanofluid is chosen as the most favorable heat carrier fluid, among others, considering its superior effectiveness, minor pressure drop, and appropriate thermal resistance compared to the pure water. Moreover, it was indicated that all cases of Ag-MgO/water hybrid nanofluid at various volume fractions (from 0.05 to 0.20) and Reynolds numbers (from 3200 to 6200) could achieve better effectiveness and lower thermal resistances, but higher pressure drops compared to the corresponding cases of pure water. Nevertheless, all the evaluated hybrid nanofluids present lower coefficient of performance (CO... [more]

Set against the United Nations Sustainable Development Goal 7, and the need to increase biomass Improved Cookstove (ICS) adoption and sustained use across the globe, this paper presents an evaluation of Practical Action Nepal’s (PAN) Results Based Financing for Improved Cookstove Market Development in Nepal (RBF) project, which was conducted between January and April 2020. Nepal has a long history of International Development assistance, yet 65.8% of rural households still use firewood as their primary source of energy. With this in mind we aimed to understand the barriers, enablers and engagement strategies for the adoption and sustained use of Improved Cookstoves (ICS), map key stakeholder role perceptions and interactions, and identify areas for improvement to increase the sustained use of ICS in the focus communities. This paper uses the methodological approach from the qualitative Technology Implementation Model for Energy (TIME) for the data collection and analysis elements. Our... [more]

Within a broader national project aimed at the hybridization of a standard city car (the 998 cc Mitsubishi-derived gasoline engine of the Smart W451), our team tackled the problem of improving the supercharger performance and response. The originally conceived design innovation was that of eliminating the mechanical connection between the compressor and the turbine. In the course of the study, it turned out that it is also possible to modify both components to extract extra power from the engine and to use it to recharge the battery pack. This required a redesign of both compressor and turbine. First, the initial configuration was analyzed on the basis of the design data provided by the manufacturer. Then, a preliminary performance assessment of the turbocharged engine allowed us to identify three “typical” operating points that could be used to properly redesign the turbomachinery. It was decided to maintain the radial configuration for both turbine and compressor, but to redesign the... [more]

The correct operation of the continuous welded track requires diagnosing its condition and preparation of track metrics requiring measurements of displacements of rail under operation. This is required as there are additional thermal stresses in the rails with values depending on the temperature changes of the rails. Therefore, the climatic conditions are important. This paper presents the original effective analytical method for diagnosing the condition of continuous welded track based on experimental research. The method allows for an appropriate repair or maintenance recommendation. In the experimental research, the authors considered track diagnostic conditions for two conditions: track under load and track without load. This paper presents empirical formulas for calculating rail temperature and longitudinal force based on ambient temperature, developed from long-term measurements. The formulas were developed for a track located on a straight section—both for a rail loaded and unlo... [more]

In this paper, the design of the terminal continuous-time sliding mode controller is presented. The influence of the external disturbances is considered. The robustness for the whole regulation process is obtained by adapting the time-varying sliding line. The representative point converges to the demand state in finite time due to the selected shape of the nonlinear switching curve. Absolute values of control signal, system velocity and both of these quantities are bounded from above and considered as system constraints. In order to evaluate the dynamical performance of the system, the settling time is selected as a quality index and it is minimized. The approach presented in this paper is particularly suited for systems in which one state (or a set of states) is the derivative of the other state (or a set of states). This makes it applicable to a wide range of electromechanical systems, in which the states are the position and velocity of the mechanical parts.

This experimental study was carried out based on the nanotechnology approach to enhance the efficacy of engine oil. Atomic and surface structures of graphene oxide (GO) nanoparticles were investigated by using a field emission scanning electron microscope and X-ray diffraction. The nano lubricant was produced by using a two-step method. The stability of nano lubricant was analyzed through dynamic light scattering. Various properties such as thermal conductivity, dynamic viscosity, flash point, cloud point and freezing point were investigated and the results were compared with the base oil (Oil- SAE-50). The results show that the thermal conductivity of nano lubricant was improved compared to the base fluid. This increase was correlated with progressing temperature. The dynamic viscosity was increased by variations in the volume fraction and reached its highest value of 36% compared to the base oil. The cloud point and freezing point are critical factors for oils, especially in cold sea... [more]

The introduction of pervasive telecommunication devices, in the scope of smart grids (SGs), has accentuated interest in the distribution network, which integrates a huge portion of new grid applications. High impact low probability (HILP) events, such as natural hazards, manmade errors, and cyber-attacks, as well as the inherent fragility of the distribution grid have propelled the development of effective resilience tools and methods for the power distribution network (PDN) to avoid catastrophic infrastructural and economical losses. Multiple resilience evaluation frameworks are proposed in the literature in order to assist distribution system operators (DSOs) in managing their networks when faced with exogenous threats. We conduct detailed analysis of existing quantitative resilience studies in both electric and telecommunication domains of a PDN, focusing on event type, metrics, temporal phases, uncertainty, and critical load. Our work adopts the standpoint of a DSO, whose target is... [more]

This article presents the development, simulation and validation of the uncertainty cost functions for a commercial building with climate-dependent controllable loads, located in Florida, USA. For its development, statistical data on the energy consumption of the building in 2016 were used, along with the deployment of kernel density estimator to characterize its probabilistic behavior. For validation of the uncertainty cost functions, the Monte-Carlo simulation method was used to make comparisons between the analytical results and the results obtained by the method. The cost functions found differential errors of less than 1%, compared to the Monte-Carlo simulation method. With this, there is an analytical approach to the uncertainty costs of the building that can be used in the development of optimal energy dispatches, as well as a complementary method for the probabilistic characterization of the stochastic behavior of agents in the electricity sector.

The ecological and economic context determine the management goals of a modern enterprise, which are in line with the growing concern about the well-being of society caused by the effects of enterprises’ activities that are particularly harmful to the environment. This increases the need to search for new tools that will have the capacity to generate information supporting the decision-making process in the area of enterprise management in terms of ecological, economic, and social goals. For these reasons, synthetic measures of development were constructed on the basis of the set of diagnostic variables describing various aspects of sustainable development in the case. Based on the environmental synthetic indicators, it has been possible to point out the Polish voivodeships, in which enterprises that are particularly harmful to the environment were able to reduce the emissions of dust and gaseous pollutants in the 2005−2019 period. These changes were often accompanied by an increase in... [more]

Optimal design of regional integrated energy systems (RIES) offers great potential for better managing energy sources, lower costs and reducing environmental impact. To capture the transition process from fossil fuel to renewable energy, a flexible RIES, including the traditional energy system (TES) based on the coal and biomass based distributed energy system (BDES), was designed to meet a regional multiple energy demand. In this paper, we analyze multiple scenarios based on a new rural community in Dalian (China) to capture the relationship among the energy supply cost, increased share of biomass, system configuration transformation, and renewable subsidy according to regional CO2 emission abatement control targets. A mixed integer linear programming (MILP) model was developed to find the optimal solutions. The results indicated that a 40.58% increase in the share of biomass in the RIES was the most cost-effective way as compared to the separate TES and BDES. Based on the RIES with m... [more]

In terms of fuel resource, hydropower possesses a prominent advantage over any other large power plants which burn fossil fuels to generate electricity. Moreover, due to the abundance in resource availability (as a domestic source in small streams and rivers), small hydropower (SHP) plants are showing prominence all over the world. SHP plants have led to improved access to electricity usage in under-developed and developing nations, thereby contributing to sustainable development goals and social empowerment. SHP, as a technology, is regarded as the largest density renewable resource with high adaptability, and low investment costs. The primary objective of the paper is to study and analyze recent developments in SHP technologies with reporting statistical figures in terms of installed capacity and MW potential in several parts of the world. Methodologies adopted by researchers to conduct techno-economic analysis of SHP projects are reviewed. Various costs involved in conducting pre-fe... [more]

One common technique employed in control system design to minimize system model complexity is model order reduction. However, controllers designed by using a reduced-order model have the potential to cause the closed-loop system to become unstable when applied to the original full-order system. Additionally, system performance improvement techniques such as disturbance observers produce unpredictable outcomes when augmented with reduced-order model-based controllers. In particular, the closed-loop system stability is compromised when a large value of observer gain is employed. In this paper, a boundary condition for the controller and observer design parameters in which the closed-loop system stability is maintained is proposed for a reduced-order proportional-integral observer compensated reduced-order model-based controller. The boundary condition was obtained by performing the stability analysis of the closed-loop system using the root locus method and the Routh-Hurwitz criterion. B... [more]

The analysis of porosity and pore structure of shale rocks has received special attention in the last decades as unconventional reservoir hydrocarbons have become a larger parcel of the oil and gas market. A variety of techniques are available to provide a satisfactory description of these porous media. Some techniques are based on saturating the porous rock with a fluid to probe the pore structure. In this sense, gases have played an important role in porosity and pore structure characterization, particularly for the analysis of pore size and shapes and storage or intake capacity. In this review, we discuss the use of various gases, with emphasis on N2 and CO2, for characterization of shale pore architecture. We describe the state of the art on the related inversion methods for processing the corresponding isotherms and the procedure to obtain surface area and pore-size distribution. The state of the art is based on the collation of publications in the last 10 years. Limitations of th... [more]

The purpose of the research was to identify the factors determining the improvement of the sustainable energy management strategy in the process of building lasting value for stakeholders, identifying key activities supporting the process of improving the sustainable energy management strategy, and analyzing the degree of use of environmental indicators by organizations in Poland. In the research process, to achieve the assumed research goals, it was decided to use the following research methods: The “Delphic Method” and the CAWI method (Computer-Assisted Web Interview). The research was carried out on a sample of 102 organizations in Poland. The study identifies goals for the sustainable development of the organization, activities supporting the process of sustainable energy management, and indicators in the field of energy management. The key factors for the improvement of energy management strategies have been identified, including implementation of modern technologies, reduction of... [more]

Competition on the local and global market forces enterprises to implement modern solutions and adapt to technological changes. Applying modern solutions allows an increase in the quality of the product and reduces production costs. The acoustic sensor, as a relatively cheap solution, allows signals to be obtained which, after appropriate processing, can be used to develop an automatic control of the longwall shearer, together with the recognition of the type of shale. This paper presents an introductory research, the goal of which has been to check whether acoustic signals carry useful information on what kind of material−shale or coal−is being cut by the cutting head of a longwall shearer. For this purpose, the fast Fourier transform and short-time Fourier transform functions implemented in MatLab were used. The results of the analysis are presented in the form of three-dimensional graphs and spectrograms. To sum up, the research carried out so far justifies the need for continuation... [more]

This paper presents issues in the field of theory, construction, calculations, as well as the design of effervescent-swirl atomizers. The results of experimental studies of spraying liquids with different physico-chemical properties for this type of atomizers are discussed. Effervescent-swirl atomization is a complex process and its mechanism is not fully understood. Therefore, the purpose of the manuscript is the complexity of the atomization process and its mechanism as well as the influence of individual parameters on its efficiency were thoroughly analyzed. The analyzed parameters include: atomizer design, outlet shape, gas and liquid flow rate, injection pressure, physicochemical properties of the atomized liquid, pressure drop, outflow coefficient, spray angle, quantitative droplet distributions, and average droplet diameter. Moreover, in the work, on the basis of the literature review, the results of the research related to, inter alia, the phenomenon of air core formation and t... [more]

The optimal state of charge (SoC) balancing control for series-connected lithium-ion battery cells is presented in this paper. A modified SoC balancing circuit for two adjacent cells, based on the principle of a bidirectional Cuk converter, is proposed. The optimal SoC balancing problem is established to minimize the SoC differences of cells and the energy loss subject to constraints of the normal SoC operating range, the balancing current, and current of cells. This optimization problem is solved using the sequential quadratic programming algorithm to determine the optimal duties of PWM signals applied to the SoC balancing circuits. An algorithm for the selection of the initial points for the optimal problem-solving process is proposed. It is applied in cases where the cost function has no decreasing part. Experimental tests are conducted for seven series-connected Samsung cells. The optimal SoC balancing control and SoC estimation algorithms are coded in MATLAB and embedded in LabVIE... [more]

The development of internal combustion engines is currently based around the ideas of downsizing and rightsizing. These trends, however, are not very widespread in vehicles with hybrid drive systems. Nevertheless, the authors analyzed the performance indicators of hybrid drives in downsized vehicles. Two generations of a vehicle model, equipped with hybrid drive systems, were used in the analysis in which not only the design of the internal combustion engine was changed, but also other hybrid drive systems (including the transmission, electric motors and high-voltage batteries). The paper analyzes the energy flow in two hybrid vehicles of different generations during tests in real road driving conditions in accordance with the requirements of the RDE (real driving emissions) tests. The authors have confirmed that newer vehicle designs extend the vehicle range by 38% in the electric mode under the conditions of road traffic (68% in the urban conditions). The application of a combustion... [more]

With the current worsening of climate change-associated risks, the transition to low-carbon energy sources has become a global priority. In this context, the advances in the implementation of smart grids, which, in addition to greater efficiency and resilience, also allow greater penetration of renewable distributed energy resources, are becoming increasingly important. However, the necessary investments will be colossal. Many specialists see the process of opening up the electric energy markets as essential to boosting these new technologies. Greater decentralization of the decision-making process can potentially promote greater scalability. However, not all liberalization reforms have led to good results. Several researchers have been evaluating experiences in different countries. Brazil, a country with continental dimensions and peculiar characteristics, already counts with a mostly renewable electric energy generation mix. In recent decades, however, it has become increasingly depe... [more]