The objective of this paper is to evaluate the contribution of energy storage systems to resource adequacy of power systems experiencing increased levels of renewables penetration. To this end, a coherent methodology for the assessment of system capacity adequacy and the calculation of energy storage capacity value is presented, utilizing the Monte Carlo technique. The main focus is on short-duration storage, mainly battery energy storage systems (BESS), whose capacity values are determined for different power and energy configurations. Alternative operating policies (OPs) are implemented, prioritizing system cost or reliability, to demonstrate the significant effect storage management may have on its contribution to system adequacy. A medium-sized island system is used as a study case, applying a mixed integer linear programming (MILP) generation scheduling model to simulate BESS and system operation under each OP, in order to determine capacity contribution and overall performance in... [more]

Flow-induced vibration is a canonical issue in various engineering fields, leading to fatigue or immediate damage to structures. This paper numerically investigates flow-induced vibrations of a cylinder interacting with the wake of another cylinder at a Reynolds number Re = 150. It sheds light on the effects of mass ratio m*, damping ratio, and mass-damping ratio m*ζ on vibration amplitude ratio A/D at different reduced velocities Ur and cylinder spacing ratios L/D = 1.5 and 3.0. A couple of interesting observations are made. The m* has a greater influence on A/D than ζ although both m* and ζ cause reductions in A/D. The m* effect on A/D is strong for m* = 2−16 but weak for m* > 16. As opposed to a single isolated cylinder case, the mass-damping m*ζ is not found to be a unique parameter for a cylinder oscillating in a wake. The vortices in the wake decay rapidly at small ζ. Alternate reattachment of the gap shear layers on the wake cylinder fuels the vibration of the wake cylinder for... [more]

According to star graph and winding distribution, winding MMFs of three kinds of 12-slot/10-pole multi-phase and multi-layer winding layout are analyzed by the improved winding function method. Analysis results show that multi-phase and multi-layer winding can suppress even order and (12n ± 1) order harmonics, thereby reducing the eddy-current loss in PMs. Based on the unfolded LPMSM model, rotor MMF, air gap flux density, and no-load back-EMF are analyzed by the analytical permeance function method, which is validated by Teslameter and no-load experiment. Winding MMF is validated by FEM. An axial-flux integrated starting/generator (ISG) with double-three-phase four-layer (DTP-FL) winding, segmented armature and PM, and centrifugal fan is designed and manufactured. The no-load and load test with two groups of resistance established has validated the reasonability of the mentioned method. Experiments show that the axial-flux ISG prototype can run at a relative temperature rise.

Knowledge of lightning impulse (LI) voltage distribution over transformer windings during the design stage of the transformer is very important. Specific design differences in inductive voltage transformers make the transient analysis approach different to the approach to the power transformers. In this paper, a methodology for acquiring lightning impulse voltage distribution over high-voltage (HV) winding of inductive voltage transformers is presented and evaluated. Resistance, inductance, and capacitance matrices are calculated using the integral and boundary element methods (BEM) approach. Additionally, in order to improve the capacitance matrix solver, adaptive cross approximation (ACA) is applied. These parameters are then used to solve the equivalent circuit model in time domain. In order to evaluate the methodology, an experimental and numerical investigation of the layer discretisation, iron core influence, and accuracy of the proposed methodology is performed. The comparison o... [more]

This paper presents an implementation of a nonlinear optimal-based wind turbine tower vibration control method. An NREL 5.0 MW tower-nacelle model equipped with a hybrid tuned vibration absorber (HTVA) is analysed against the model equipped with a magnetorheological TVA (MRTVA). For control purposes, a 3 kN active actuator in parallel with a passive TVA is used in the HTVA system, while an MR damper is built in the MRTVA instead of a viscous damper, as in a standard TVA. All actuator force constraints are embedded in the implemented nonlinear control techniques. By employing the Pontryagin maximum principle, the nonlinear optimal HTVA control proposition was derived along with its simplified revisions to avoid a high computational load during real-time control. The advantage of HTVA over MRTVA in vibration attenuation is evident within the first tower bending frequency neighbourhood, with HTVA also requiring less working space. Using the appropriate optimisation fields enabled an 8-fol... [more]

The viability of Variable Renewable Energy (VRE)-investment strategies depends on the response of dispatchable producers to satisfy the net load. We lack a simple research tool with sufficient complexity to represent major phenomena associated with the response of dispatchable producers to the integration of high shares of VRE and their impact on system costs. We develop a minimization of the system cost allowing one to quantify and decompose the system value of VRE depending on an aggregate dispatchable production. Defining the variable cost of the dispatchable generation as quadratic with a coefficient depending on macroeconomic factors such as the cost of greenhouse gas emissions leads to the simplest version of the model. In the absence of curtailment, and for particular parameter values, this version is equivalent to a mean-variance problem. We apply this model to France with solar and wind capacities distributed over the administrative regions of metropolitan France. In this case... [more]

Nuclear and renewables energies are the two variants for low-carbon energy and the evolving grid suggests possible synergies between them. Nuclear energy introduces supple operations based on power demand, while renewables such as PV and wind hybrid systems depend on the presence and strength of sunlight or wind. For grid stability, there is need to improve their performance in order to overcome the impact of this disadvantage. The paper is a step in this direction as it addresses a detailed comprehensive dynamic modeling and an efficient control of grid-connected energy sources such as PV or wind system to increase system reliability and to ensure the power quality and safe operation of critical demands. The behavior of the suggested hybrid system is tested at different climate circumstances such as variation of sun radiation and wind speed. The PV is equipped with a boost converter and a three-phase pulse width modulation (PWM) inverter. The wind energy comprises a doubly fed generat... [more]

The optimal expansion of AC medium-voltage distribution grids for rural applications is addressed in this study from a heuristic perspective. The optimal routes of a distribution feeder are selected by applying the concept of a minimum spanning tree by limiting the number of branches that are connected to a substation (mixed-integer linear programming formulation). In order to choose the caliber of the conductors for the selected feeder routes, the maximum expected current that is absorbed by the loads is calculated, thereby defining the minimum thermal bound of the conductor caliber. With the topology and the initial selection of the conductors, a tabu search algorithm (TSA) is implemented to refine the solution with the help of a three-phase power flow simulation in MATLAB for three different load conditions, i.e., maximum, medium, and minimum consumption with values of 100%, 60%, and 30%, respectively. This helps in calculating the annual costs of the energy losses that will be summ... [more]

Developments in the design of wind turbines with augmentation are advancing around the globe with the goal of generating electricity close to the user in built-up areas. This is certain to help lessen the power generation load as well as distribution and transmission network costs by reducing the distance between the user and the power source. The main objectives driving the development and advancement of vertical-axis wind turbines are increasing the power coefficient and the torque coefficient by optimizing the upstream wind striking on the rotor blades. Unlike horizontal-axis wind turbines, vertical axis turbines generate not only positive torque but also negative torque during operation. The negative torque generated by the returning blade is a key issue for vertical-axis wind turbines (VAWTs) that is counterproductive. Installation of wind deflectors for flow augmentation helps to reduce the negative torque generated by the returning blades as well as enhance the positive torque b... [more]

In a nuclear power plant environment, low-voltage cables experience different stresses during their service life which challenge their integrity. A non-destructive and reliable condition monitoring technique is desired to determine the state of these low-voltage cables during service and for the life extension of nuclear power plants. Hence, in this research work, an EPR/CSPE-based low-voltage cable was exposed to γ-rays for five different absorbed doses. The overall behavior of the cable under stress was characterized by frequency and time domain electrical measurements (capacitance, tan δ, and Extended Voltage Response) and a mechanical measurement (elongation at break). Significant variations in the electrical parameters were observed, as was a decline in the elongation at break values. A strong correlation between the measurement methods was observed, showing the ability of the electrical methods to be adopted as a non-destructive condition monitoring technique.

One of the key challenges of developing countries is to tackle the mitigation of the impacts of rapid and uncontrolled urbanization. Assessing this phenomenon is crucial to lessen the consequences for the environment and society. ‘Literature has been concentrated in planning strategies for the cities’ adaptation and engagements to the principles of green development ensuring a long-term quality of life for their citizens. Hereby, smart technologies and applications consist of two of the most encouraging concepts for solutions for achieving the 2030 and 2050 horizon targets towards clean energy transition and carbon neutrality. In academia, scholars have already raised the importance of ‘smartness’ to define the adaptative patterns for the global pressures of climate change and uncontrolled urban growth. The mitigation of these phenomena is crucial to ensure the cities’ future and lessen their impacts. This study seeks a strategic and smart-driven vision to leverage smartness on the phe... [more]

The objectives of this work are: (a) to present a new system for building heating which is based on underground energy storage, (b) to develop a mathematical model of the system, and (c) to optimise the energy performance of the system. The system includes Photovoltaic Thermal Hybrid Solar Panels (PVT) panels with cooling, an evacuated solar collector and a water-to-water heat pump. Additionally, storage tanks, placed underground, are used to store the waste heat from PVT panels cooling. The thermal energy produced by the solar collectors is used for both domestic hot water preparation and thermal energy storage. Both PVT panels and solar collectors are assembled with a sun-tracking system to achieve the highest possible solar energy gain. Optimisation of the proposed system is considered to achieve the highest Renewable Energy Sources (RES) share during the heating period. Because the resulting optimisation problem is nonlinear, the classical gradient-based optimisation algorithm give... [more]

This paper proposes an equivalent circuit model to obtain the transient electrical stress quantitatively in medium voltage medium frequency transformers in modern power electronics. To verify this model, transient simulation is performed on a 1.5 kV/1 kHz transformer, revealing voltage overshoot quantitatively between turns and layers of the transformer’s HV winding. Effects of rise time of the input pulse voltage, stray capacitance of the winding insulation, and their interactions on the voltage overshot magnitude are presented. With these results, we propose limiting the voltage overshoot and, thereafter, enhancing medium voltage medium frequency transformer’s insulation capability, which throws light on the transformer’s insulation design. Additionally, guidance on the future studies on aging and endurance lifetime of the medium voltage medium frequency transformer’s insulation could be given.

The article presents the results of preliminary research aimed at determining the possibility of using microencapsulated phase change material (mPCM) slurries as a working fluid in installations with a flat liquid solar collector. In the tests, the following were used as the working fluid: water (reference liquid) and 10% wt. and 20% wt. of an aqueous solution of the product under the trade name MICRONAL® 5428 X. As the product contained 43% mPCM, the mass fraction of mPCM in the working liquid was 4.3% and 8.6%, respectively. The research was carried out in laboratory conditions in the range of irradiance I = 250−950 W/m2. Each of the three working fluids flowed through the collector in the amount of 20 kg/h, 40 kg/h, and 80 kg/h. The working fluid was supplied to the collector with a constant temperature Tin = 20 ± 0.5 °C. It was found that the temperature of the working fluid at the collector outlet increases with the increase in the radiation intensity, but the temperature achieved... [more]

Integration of renewable energy resources and conventional grids leads to an increase in power quality issues. These power quality issues require different standards to be followed for accurate measurement and monitoring of various parameters of the power system. Conventional power quality analyzers (PQAs) are programmed to a particular standard and cannot be reconfigured by the end user. Therefore, conventional PQAs cannot meet the challenges of a rapidly changing grid. In this regard, a Compact RIO-based (CRIO-based) PQA was proposed, that can be easily reprogrammed and cope with the challenges faced by conventional PQAs. The salient features of the proposed PQA are a high processing speed, interactive interface, and high-quality data-storage capacity. Moreover, unlike conventional PQAs, the proposed PQA can be monitored remotely via the internet. In this research, a hardware-in-loop (HIL) simulation is used for performing the power-quality assessment in a systematic manner. Power qu... [more]

This comparative study inspects the heat transfer characteristics of magnetohydrodynamic (MHD) nanofluid flow. The model employed is a two-phase fluid flow model. Water is utilized as the base fluid, and zinc and titanium oxide (Zn and TiO2) are used as two different types of nanoparticles. The rotation of nanofluid is considered along the z-axis, with velocity  ω*. A similarity transformation is used to transform the leading structure of partial differential equations to ordinary differential equations. By using a powerful mathematical BVP-4C technique, numerical results are obtained. This study aims to describe the possessions of different constraints on temperature and velocity for rotating nanofluid with a magnetic effect. The outcomes for the rotating nanofluid flow and heat transference properties for both types of nanoparticles are highlighted with the help of graphs and tables. The impact of physical concentrations such as heat transference rates and coefficients of skin f... [more]

This empirical study assesses the effect of CO2 emissions, urbanization, energy consumption, and agriculture on Thailand’s economic growth using a dataset between 1970 and 2018. The ARDL and the frequency domain causality (FDC) approaches were applied to assess these interconnections. The outcome of the bounds test suggested a long-term association among the variables of investigation. The ARDL outcomes reveal that urbanization, agriculture, energy consumption, and CO2 emissions positively trigger Thailand’s economic growth. Additionally, the frequency domain causality test was used to detect a causal connection between the series. The main benefit of this technique is that it can detect a causal connection between series at different frequencies. To the understanding of the authors, this is the first study in the case of Thailand that will apply the FDC approach to capture the causal linkage between GDP and the regressors. The outcomes of the causality test suggested that CO2 emission... [more]

This research proposes a generic smart cloud-based system in order to accommodate multiple scenarios where agriculture farms using Internet of Things (IoTs) need to be monitored remotely. The real-time and stored data are analyzed by specialists and farmers. The cloud acts as a central digital data store where information is collected from diverse sources in huge volumes and variety, such as audio, video, image, text, and digital maps. Artificial Intelligence (AI) based machine learning models such as Support Vector Machine (SVM), which is one of many classification types, are used to accurately classify the data. The classified data are assigned to the virtual machines where these data are processed and finally available to the end-users via underlying datacenters. This processed form of digital information is then used by the farmers to improve their farming skills and to update them as pre-disaster recovery for smart agri-food. Furthermore, it will provide general and specific infor... [more]

The increasing use of electric vehicles in road and air transportation, especially in last-mile delivery and city mobility, raises new operational challenges due to the limited capacity of electric batteries. These limitations impose additional driving range constraints when optimizing the distribution and mobility plans. During the last years, several researchers from the Computer Science, Artificial Intelligence, and Operations Research communities have been developing optimization, simulation, and machine learning approaches that aim at generating efficient and sustainable routing plans for hybrid fleets, including both electric and internal combustion engine vehicles. After contextualizing the relevance of electric vehicles in promoting sustainable transportation practices, this paper reviews the existing work in the field of electric vehicle routing problems. In particular, we focus on articles related to the well-known vehicle routing, arc routing, and team orienteering problems.... [more]

For many applications, the possibility of controlling heat flow by “thermal switching” could be very beneficial. Several concepts for heat switches were already proposed and tested, however, many drawbacks of these concepts are evident. In this work, we present a novel approach for thermal switching using a water-loaded adsorbent as part of the evaporator of a heat pipe. The basic idea is that the adsorbent releases water upon exceeding a certain evaporator temperature, and thus “activates” the heat pipe by providing the working fluid for thermal transport. The first part of this work concentrates on the adsorbent characterization by analyzing the adsorption isobars and isotherms and thus understanding the behavior of the system. Furthermore, a model to predict the release of water from the adsorbent in dependence of temperature was developed. Subsequently, the adsorbent was integrated into an actual heat pipe demonstrator to verify these predictions and demonstrate the thermal switchi... [more]

The article presents the possibility of verifying the efficiency of a diesel particulate filter (DPF) with the use of particle counters using two different measurement methods. The tests were carried out at a vehicle inspection station using a condensation particle counter (CPC) and a diffusion charger (DC). This article presents the results of measurements of 50 vehicles. Removal of the diesel particulate filter from a vehicle is prohibited but is a known phenomenon throughout the EU. The task of periodic technical inspections is to eliminate vehicles that are inoperative and do not meet the environmental protection requirements. However, to date, European vehicle inspection stations do not have an effective tool to counter tampering with diesel particulate filters. The performed measurements allowed us to prove the hypothesis that both methods of measurement allow the effective confirmation of the presence of DPF in a vehicle during the periodic technical inspection of the vehicle an... [more]

One of the most common problems in science is to investigate a function describing a system. When the estimate is made based on a classical mathematical model (white-box), the function is obtained throughout solving a differential equation. Alternatively, the prediction can be made by an artificial neural network (black-box) based on trends found in past data. Both approaches have their advantages and disadvantages. Mathematical models were seen as more trustworthy as their prediction is based on the laws of physics expressed in the form of mathematical equations. However, the majority of existing mathematical models include different empirical parameters, and both approaches inherit inevitable experimental errors. Simultaneously, the approximation of neural networks can reproduce the solution exceptionally well if fed sufficient data. The difference is that an artificial neural network requires big data to build its accurate approximation, whereas a typical mathematical model needs se... [more]

With the increase in the voltage level and number of transmission lines, the probability of lightning strikes on transmission lines is significantly increased, while lightning breakage accidents occur frequently. Therefore, an explosion airflow arc-quenching gap for 110 kV transmission lines was developed based on the idea of rapid extinction. A mathematical model of the detonation wave based on the CJ (Chapman−Jouget) detonation wave theory was developed to calculate the detonation air pressure and analyze its influencing factors. ANSYS software and the magnetohydrodynamic (MHD) model were used to simulate the process of detonation airflow coupled with an arc, and the simulation results indicated that the power frequency arc was evidently suppressed with the influence of airflow, which can effectively prevent arcing. A combined impulse and power frequency test and arc-quenching tests were performed to verify the effectiveness of the arc-quenching gap. The results of the combined test... [more]

This paper presents a comparison of 30/8 and 12/8 AC permanent magnet motors with distributed (DW) and concentrated winding (CW) designed for electric vehicle traction. Both prototypes are based on an interior permanent magnet (IPM) motor topology and contain V-shape magnets. The radial flux AC IPM motors were designed for an 80 kW propulsion system to achieve 125 N·m. Finite element models (FEM) used to design the geometry of IPM motors and the required useful parameters of electric motors are widely investigated. The accuracy of finite element models is verified and validated on the basis of test data. Numerical simulations of healthy and faulty operation states, and studies of winding faults based on the FEM offer a deeper understanding of the associated phenomena. Therefore, in this paper, a short-circuit fault in a stator winding was simulated to investigate the transient currents under an external load collapse, for all winding phases. These simulations were used to define other... [more]

Currently, renewable energy is increasingly important in the energy sector. One of the so-called renewable energy sources is geothermal energy. The most popular solution implemented by both small and large customers is the consumption of low-temperature geothermal energy using borehole heat exchanger (BHE) systems assisted by geothermal heat pumps. Such an installation can operate regardless of geological conditions, which makes it extremely universal. Borehole heat exchangers are the most important elements of this system, as their design determines the efficiency of the entire heating or heating-and-cooling system. Filling/sealing slurry is amongst the crucial structural elements. In borehole exchangers, reaching the highest possible thermal conductivity of the cement slurry endeavors to improve heat transfer between the rock mass and the heat carrier. The article presents a proposed design for such a sealing slurry. Powdered magnesium was used as an additive to the cement. The appro... [more]