Due to the internal dynamics of the modular multilevel converter (MMC), the coupling between the positive and negative sequences in impedance, which is defined as frequency coupling, inherently exists in MMC. Ignoring the frequency coupling of the MMC impedance model may lead to inaccurate stability assessment, and thus the multi-input multi-output (MIMO) impedance model has been developed to consider the frequency coupling effect. However, the generalized Nyquist criterion (GNC), which is used for the stability analysis of an MIMO model, is more complicated than the stability analysis method applied on single-input-single-output (SISO) models. Meanwhile, it is not always the case that the SISO model fails in the stability assessment. Therefore, the conditions when the MIMO impedance model needs to be considered in the stability analysis of an MMC system should be analyzed. This paper quantitatively analyzes the effect of frequency coupling on the stability analysis of grid-connected M... [more]

This paper proposes a second-order thermal model for electrical machines. The goal of this model is the prediction of the average winding temperature during short and long thermal transients up to the steady-state conditions. First, the thermal parameters of the electrical machine are determined by a DC test. Then, the proposed model is characterized and validated using AC tests. The accuracy of the proposed thermal model has been verified comparing the computed temperatures with the measured ones. The maximum error found during the thermal transient is lower than 3%, an excellent result comparing the complexity of a total enclosed fan cooled induction motor and the simplicity of the proposed model.

Absorption Refrigeration Systems (ARS) are potential alternatives to direct expansion (DX) refrigeration systems. This review focused on the incorporation of an ejector into absorption refrigeration cycles to constitute Hybrid Ejector-Absorption Refrigeration Systems (HEARS). The ejector adds several advantages to the absorption refrigeration systems depending on its location in the cycle. The two prevalent configurations of HEARS are Triple pressure level (TPL-HEARS), and Low Pressure Condenser (LPC-HEARS). Previous studies revealed the preference of the latter configuration as it allows lower circulation ratios, enhances the refrigeration effect, and could achieve a COP up to 1. Moreover, LPC configuration is suitable with single, double, and variable-effect absorption systems with a COP of above unity. In turn, the TPL-HEARS notably enhances the absorption process, particularly when a variable geometry ejector is utilized. This configuration could obtain a COP around 1.1, but only w... [more]

This study was a preliminary investigation of solid recovered fuel production from spent coffee grounds using the hydrothermal carbonization (HTC) technique. The spent coffee grounds (SCGs) were subjected to HTC at 170 to 250 °C. The biochar was characterized by proximate analysis, ultimate analysis, capillary suction time, time to filter, suspended solids, and particle size distribution. The biochar yields decreased with increasing HTC temperature and time. However, the higher heating value (HHV) of biochar increased with the HTC temperature and time. The H/C slop relative to the O/C atomic rate of spent coffee grounds was 0.10 with low decarboxylation selectivity. Considering the HHV of biochar and dehydration capacity depend on ratio of H/C vs. O/C, the optimum reaction temperature of HTC was 200 °C, and the biochar from SCGs is an attractive biochar.

We study the wave anelasticity (attenuation and velocity dispersion) of a periodic set of three flat porous layers saturated by two immiscible fluids. The fluids are very dissimilar in properties, namely gas, oil, and water, and, at most, three layers are required to study the problem from a general point of view. The sequence behaves as viscoelastic and transversely isotropic (VTI) at wavelengths much longer than the spatial period. Wave propagation causes fluid flow and slow P modes, inducing anelasticity. The fluids are characterized by capillary forces and relative permeabilities, which allow for the existence of two slow modes and the presence of dissipation, respectively. The methodology to study the physics is based on a finite-element uspcaling approach to compute the complex and frequency-dependent stiffnesses of the effective VTI medium. The results of the experiments indicate that there is higher dissipation and anisotropy compared to the widely used model based on an effect... [more]

The nature of carbonate deposition as well as diagenetic processes can cause the development of unique geological features such as cavities, vugs and fractures. These are called karsts. Encountering karsts while drilling can lead to serious consequences such as severe mud losses, drops of bottom hole assembly and gas kicks. To improve drilling safety in intervals of karstification, it is important to detect karsts as early as possible, preferably in advance. In this paper, we review methods and technologies that can be used for the prediction and early detection of karsts. In particular, we consider acoustic, resistivity, seismic and drilling-data methods. In addition to the inventions and technologies developed and published over the past 40 years, this paper identifies the advantages, limitations and gaps of these existing technologies and discusses the most promising methods for karst detection and prediction.

This paper poses the question: ‘can energy innovation initiatives in Innovation Playgrounds foster a new ‘energy urbanity’ through active citizen participation in the energy transition?’ The concept of ‘Innovation Playgrounds’ and an accompanying Framework are described and linked to implementation evidence of the EU H2020 positive energy research and innovation project +CityxChange, related to emergent active citizen participation in two cities: Limerick, Ireland and Trondheim, Norway. The purpose of the study is to demonstrate that spatially clustered energy innovation initiatives in urban areas involving active citizen participation contribute to a new ‘energy urbanity’ for the energy transition. The research methods are based on a comparative case study approach and close observation of two case sites, with a focus on the ‘Innovation Playground’ area of each city. The article’s three main conclusions are: that a Framework approach to active citizen participation in energy innovatio... [more]

Wakes appearing downstream of disturbances on the surface of a water flow in a concave open channel were examined experimentally. The investigated channel geometry was similar to the liquid lithium target in DONES (Demonstration fusion power plant Oriented NEutron Source). The objective of the measurements was to analyze the effect of a disturbance on the downstream layer thickness. For measuring the height profiles in the channel, an optical measurement system based on laser triangulation was developed. It was shown that the wake of the undisturbed flow emerged from the nozzle corner, which was in accordance with analytical solutions. For sufficiently large disturbances at the nozzle edge, the height profiles located downstream showed symmetrical minima and maxima on both sides of the disturbance. The wake depth strongly depended on the diameter and penetration depth of the disturbance, as well as the circumferential position in the channel, which yields to a critical wake depth of on... [more]

A study on forced ignition characteristics of RP-3 jet fuel-air mixture was conducted around a constant volume combustion vessel and a nanosecond pulsed plasma discharge power supply. Experiments were carried out at different initial pressures (pu = 0.2, 0.3, 0.5 atm), equivalence ratios (ϕ = 0.7, 0.8, 1.1), steam concentrations (ZH = 0%, 10%, 15%) and oxygen concentrations (ZO = 13.5%, 16%, 21%). The relationship between ignition probability and ignition energy is investigated. The experimental results show that the decrease in pressure, equivalence ratio, oxygen concentration and the increase in steam concentration all lead to an increase in minimum ignition energy (MIE). In order to further analyze the experimental data, one existing fitting equation is reformed with the initial conditions taken into account. Multivariate fitting is carried out for different conditions, and the fitting results of ignition probability are in good agreement with the experiments. The MIE results under... [more]

This is a reply to the paper by Variny et al. [...]

The manufacturing of thermally stable solar coatings with high photo-thermal performance represents a key factor for the further deployment of the CSP technology. Since 2005, ENEA has been developing solar coatings suitable for medium and high temperature applications based on the technology of double nitride cermet, by employing silver and tungsten as infrared reflectors, respectively. Thanks to the high infrared reflectance of silver, the corresponding coatings have better optical performance than those with tungsten; however, the high diffusivity of silver compromises its use at high temperature. In order to improve the structural and chemical stability at medium and high temperature of coatings based on silver, this infrared reflector was placed between compact and uniform layers of metal and cermet manufactured by using high-energy and fast deposition processes. In particular, an Unbalanced Magnetron cathode was adopted to promote an ion-assisted deposition process that improved u... [more]

In recent years, the role of digital enterprises in the global economy has been growing. The issue of assessing their impact on social aspects is noticeable. The aim of the article is to show social impact as a key factor in the development of digital business models. The Analytic Hierarchy Process (AHP) method used and the criteria for social impact assessments based on heuristic methods allowed for the components of business models that relate to social impact to be ranked, and subsequently for socially oriented enterprises functioning in the digital economy to be ranked. The companies selected for the research are understood by the authors as digital business models, the concept of which is embedded in a pro-social management intention. Purposive sampling, which in this situation was considered to be the most effective in terms of the objective of the paper, was applied. The literature review, analyses and heuristic research have demonstrated that the social factor in modern applica... [more]

New technologies reaching out for meeting the needs of an aging population in developed countries have given rise to the development and gradual implementation of the concept of an autonomous vehicle (AV) and have even made it a necessity and an important business paradigm. However, in parallel, there is a discussion about consumer preferences and the willingness to pay for new car technologies and intelligent vehicle options. The main aim of the study was to analyze the impact of selected factors on the perception of the future of autonomous cars by respondents from the area of Southeastern Poland in terms of a comparison with traditional cars, with particular emphasis on the advantages and disadvantages of this concept. The research presented in this study was conducted in 2019 among a group of 579 respondents. Data analysis made it possible to identify potential advantages and disadvantages of the concept of introducing autonomous cars. A positive result of the survey is that 68% of... [more]

The aim of this research is to investigate the effects of a direct current (DC) electric field on the combustion behavior of a co-flow propane diffusion flame. The flame length and NOx emission were observed and measured. The electric field enhances the combustion process of propane diffusion flame by causing the movement of ions and molecules in the flame, resulting in a change in the shape of the flame. The flame heights decrease with an increase in the applied voltage and polarity, a more dominant effect to be observed with a positive DC electric field. However, for the applied negative polarity, the inner-cone of the propane diffusion flame is shifted by the electric field. Drastic reduction in the NOx emission is observed with an increase in the applied DC voltage and polarity. In the existing system, the reduction percentage of NOx is within the range of 55 to 78%.

This paper presents the results of a study conducted to determine the dynamic power of a hydraulic leg. The hydraulic leg is the basic element that maintains the position of a powered roof support. It is located in the structure between the canopy and the floor base. The analysis assumes that its power must be greater than the energy of the impact of the rock mass. The energy of the rock mass is generated by tremors caused mainly by mining exploitation. The mining and geological structure of the rocks surrounding the longwall complex also have an influence on this energy generation. For this purpose, stationary tests of the powered roof support were carried out. The analysis refers to the space under the piston of the leg, which is filled with fluid at a given pressure. The bench test involved spreading the leg in the test station under a specified pressure. It was assumed that the acquisition of dynamic power would be at the point of pressure and increase in the space under the piston... [more]

The aim of the study is to present the implemented “smart” solutions and the developed indicators of their measurement in the context of the city of Częstochowa (Poland), as well as a participant in the “Benchmarking—we are looking for the best smart city solutions”. In order to achieve the assumed goal, a traditional review of the literature on the subject in the field of “smart city” was carried out. Then, the methodological assumptions related to developing a model set of indicators for cities participating in the program have been presented. In addition, a comparative analysis of the obtained indicators values for cities, Częstochowa and Bydgoszcz, has been carried out in the scope of one exemplary measure. The proposed research procedure can be used to analyze and evaluate cities in the country, as well as to select alternative solutions in the context of other urban features. Due to the fact that other cities in Poland will also participate in the study, the significance of this... [more]

The European Commission emphasised that a bioeconomy is an economy that uses renewable biological resources from the land and sea (e [...]

This work aims to systematically investigate the influence of process temperature, biomass-to-water ratio, and production scales (laboratory and pilot) on the chemical composition of aqueous and gaseous phases and mass production of chemicals by hydrothermal processing of Açaí (Euterpe oleraceae, Mart.) seeds. The hydrothermal carbonization was carried out at 175, 200, 225, and 250 °C at 2 °C/min and a biomass-to-water ratio of 1:10; at 250 °C at 2 °C/min and biomass-to-water ratios of 1:10, 1:15, and 1:20 in technical scale; and at 200, 225, and 250 °C at 2 °C/min and a biomass-to-water ratio of 1:10 in laboratory scale. The elemental composition (C, H, N, S) in the solid phase was determined to compute the HHV. The chemical composition of the aqueous phase was determined by GC and HPLC and the volumetric composition of the gaseous phase using an infrared gas analyzer. For the experiments in the pilot test scale with a constant biomass-to-water ratio of 1:10, the yields of solid, liqu... [more]

The switching loss of the secondary side rectifiers in LLC resonant converters can have a noticeable impact on the overall efficiency of the complete power supply and constrain the upper limit of the optimum switching frequencies of the converter. Two are the main contributions to the switching loss in the secondary side rectifiers: on the one hand, the reverse recovery loss (Qrr), most noticeably while operating above the series resonant frequency; and on the other hand, the output capacitance (Coss) hysteresis loss, not previously reported elsewhere, but present in all the operating modes of the converter (under and above the series resonant frequency). In this paper, a new technique is proposed for the measurement of the switching losses in the rectifiers of the LLC and other isolated converters. Moreover, two new circuits are introduced for the isolation and measurement of the Coss hysteresis loss, which can be applied to both high-voltage and low-voltage semiconductor devices. Fin... [more]

The world is transitioning from the conventional grid to the smart grid at a rapid pace. Innovation always comes with some flaws; such is the case with a smart grid. One of the major challenges in the smart grid is to protect it from potential cyberattacks. There are millions of sensors continuously sending and receiving data packets over the network, so managing such a gigantic network is the biggest challenge. Any cyberattack can damage the key elements, confidentiality, integrity, and availability of the smart grid. The overall smart grid network is comprised of customers accessing the network, communication network of the smart devices and sensors, and the people managing the network (decision makers); all three of these levels are vulnerable to cyberattacks. In this survey, we explore various threats and vulnerabilities that can affect the key elements of cybersecurity in the smart grid network and then present the security measures to avert those threats and vulnerabilities at th... [more]

Advances in power electronics and their use in Miscellaneous Electric Loads (MELs) in buildings have resulted in increased interest in using low-voltage direct current (DC) power distribution as a replacement for the standard alternating current (AC) power distribution in buildings. Both systems require an endpoint converter to convert the distribution system voltage to the MELs voltage requirements. This study focused on the efficiency of these endpoint converters by testing pairs of AC/DC and DC/DC power converters powering the same load profile. In contrast to prior studies, which estimated losses based on data sheet efficiency and rated loads, in this study, we used part load data derived from real-world time-series load measurements of MELs and experimentally characterized efficiency curves for all converters. The measurements performed for this study showed no systematic efficiency advantage for commercially available DC/DC endpoint converters relative to comparable, commercially... [more]

This paper presents the development and evaluation of EnnerSpectrum, a platform for electricity monitoring. The development was motivated by a gap between academic, fully custom-made monitoring solutions and commercial proprietary monitoring approaches. EnnerSpectrum is composed of two main entities, the back end, and the Gateway. The back end is a server comprised of flexible entities that can be configured to different monitoring scenarios. The Gateway interacts with equipment at a site that cannot interact directly with the back end. The paper presents the architecture and configuration of EnnerSpectrum for a long-term case study with 13 prosumers of electricity for approximately 36 months. During this period, the proposed system was able to adapt to several building and monitoring conditions while acquiring 95% of all the available consumption data. To finalize, the paper presents a set of lessons learned from running such a long-term study in the real world.

Advances in remote data acquisition techniques have contributed to the flooding of society with spatial data sets and information. Widely available spatial data sets, including digital terrain models (DTMs) from aerial laser scanning (ALS) data, are finding more and more new applications. The article analyses and compares the heights of the 14 highest peaks of the Polish Carpathians derived from different data sources. Global navigation satellite system (GNSS) geodetic measurements were used as reference. The comparison primarily involves ALS data, and selected peaks’ GNSS measurements carried out with Xiaomi Mi 8 smartphones were also compared. Recorded raw smartphone GNSS measurements were used for calculations in post-processing mode. Other data sources were, among others, global and local databases and models and topographic maps (modern and old). The article presents an in-depth comparison of Polish and Slovak point clouds for two peaks. The results indicate the possible use of la... [more]

This study is related to the heat energy transfer during 3D nanofluid (water-based) motion over a rotating surface by incorporating the combined impacts of thermal radiations and couple stress. The flow is modeled by a set of non-linear coupled PDEs, which is converted to a set of coupled non-linear ODEs by using suitable similarity transformations. The transformed equations are solved with the built-in NDSolve command. The effects of relevant interesting parameters on the nanofluid velocity components and temperature distribution are explained through various graphs. It is found that the velocity component f(η) is increased with higher values of γ and A0 while it drops with an increasing rotation parameter and nanoparticle volume fraction. The fluid temperature increases with higher αnf, Rd, ϵ2, ϵ3, A1 and drops with increasing Pr, ϵ1 and couple stress parameter (A0). The Nusselt number remains constant at a fixed Pr and Rd, whereas it increases with increasin... [more]

Developing wind energy in Lithuania is one of the most important ways to achieve green energy goals. Observational data show that the decline in wind speeds in the region may pose challenges for wind energy development. This study analyzed the long-term variation of the observed 2006−2020 and projected 2006−2100 near-surface wind speed at the height of 10 m over Lithuanian territory using data of three models included in the Coupled Model Intercomparison Project phase 5 (CMIP5). A slight decrease in wind speeds was found in the whole territory of Lithuania for the projected wind speed data of three global circulation models for the scenarios RCP2.6, RCP4.5, and RCP8.5. It was found that the most favorable scenario for wind energy production is RCP2.6, and the most unfavorable is the RCP4.5 scenario under which the decrease in wind speed may reach 12%. At the Baltic Sea coastal region, the decline was smaller than in the country’s inner regions by the end of the century. The highest red... [more]