In this work, a novel workflow has been proposed, validated and applied to interpret the early time transient pressure data in tight oil reservoirs with physical constraints. More specifically, the theoretical model was developed to obtain the transient pressure response for a vertical well in tight oil reservoirs with consideration of pseudo threshold pressure gradient (TPG). Then, a physical constraint between the skin factor and formation permeability has been proposed based on the physical meaning of percolation theory. This physical constraint can be applied to determine the lower limit of the skin factor which can reduce the uncertainty during the interpretation process. It is found that the influence range of the skin factor and permeability may partially overlap during the interpretation process without consideration of physical constraints. Additionally, it is found that the equivalent wellbore radius is more reasonable by considering the skin factor constraints. Furthermore,... [more]

Previous gas hydrate production tests conducted by the Guangzhou Marine Geological Survey (GSGM) in 2017 and 2020 indicated the great potential of gas hydrates in the Shenhu Sea area in the Pearl River Mouth Basin (PRMB), China. In this study, the effects of deposition processes in submarine canyons and the distribution of gas chimneys on gas hydrate accumulation were investigated using high-resolution two- dimensional (2D) and three-dimensional (3D) seismic data. Four intact submarine canyons were identified in the study area. Five deepwater depositional elements are closely related to submarine canyons: lateral accretion packages (LAPs), basal lags, slides, mass transport deposits (MTDs), and turbidity lobes. MTDs and lobes with multiple stages outside the distal canyon mouth reveal that the sedimentary evolution of the canyon was accompanied by frequent sediment gravity flows. Gas chimneys originating from Eocene strata are generally up to 3 km wide and distributed in a lumpy or ban... [more]

In 2022, the record of extreme weather events already includes deep droughts in Sichuan province, China, and California, US; floods inundating a third of Pakistan and serious and repeated flooding in Eastern Australia; heat waves and drought in Europe; and wildfires in Europe and the western US [...]

Squirrel-cage fans are widely applied in air conditioning systems, and their aerodynamic noise mainly related to blade length. The aerodynamic performance and noise spectrum of squirrel-cage fans are synchronously measured in an anechoic wind tunnel. The effect of blade lengths and different geometric configurations on the noise of a squirrel-cage fan is experimentally investigated. This paper focuses on the total sound pressure level and noise spectrum characteristics at different measurement points. Noise distributions of the outlet of the forward squirrel-cage fan exhibited axial-symmetry and large differences for those of vertical direction. In lower fan positions, the noise was greater than that of the top. In particular, it was found that blades were easy to generate higher noise when their length was reduced by 31.7%. The findings suggest that the broadband noise of the squirrel-cage fan should be fully considered for noise reduction. The purpose of this work is to provide a nov... [more]

This is a conference extension of the paper ‘Investigation on the mature storm cloud’s electric field using long airborne antennas’. The use of vertical antennas (including the VEDs—Vertical Electric Dipoles), lifted up by aerostats to high altitudes without being anchored to the ground, presents numerous advantages in comparison with large terrestrial VLF (Very Low Frequency) antenna structures. A slow-moving floating-earth conductor—a vertical wire antenna—is subjected to intense electrification mechanisms in the atmosphere and inside the cloud layers, producing additional risks for the transmitter and the flight train itself. The electrical potential achieved in this process is, therefore, compared with the flashover voltages over the antenna’s upper fixing point, defining the voltage margins at which the VLF transmitter is able to operate. The electrification processes are also compared to the model based on experimental data on the occurrence of corona discharges over a long, vert... [more]

Humankind has an urgent need to reduce carbon dioxide emissions. Such a challenge requires deep transformation of the current energy system in our society. Achieving this goal has given an unprecedented role to decarbonized energy vectors. Electricity is the most consolidated of such vectors, and a molecular vector is in the agenda to contribute in the future to those end uses that are difficult to electrify. Additionally, energy storage is a critical issue for both energy vectors. In this communication, discussion on the status, hopes and perspectives of the hydrogen contribution to decarbonization are presented, emphasizing bottlenecks in key aspects, such as education, reskilling and storage capacity, and some concerns about the development of a flexible portfolio of technologies that could affect the contribution and impact of the whole hydrogen value chain in society. This communication would serve to the debate and boost discussion about the topic.

Heat pipes (HPs) are gaining increasing popularity in the propulsion motors of transportation electrification due to their remarkable thermal properties. However, the inclination angle affects the HP thermal performance and, thus, results in temperature nonuniformity, which may generate unbalanced thermal stress on the motor. Such an issue has received less attention to date and requires corresponding solutions. This article performs an experimental investigation on motor temperature nonuniformity with HPs and further proposes an improved structure to address this problem. A specimen based on a stator-winding assembly with HPs is prepared and a dedicated experimental platform is established. Then, the temperature distribution across the specimen is studied, followed by an evaluation of the effects of current density and wind velocity. To compensate for the degradation of HP thermal performance, an improved structure with enlarged fins is proposed, and the equilibrium point is determine... [more]

Hydrocarbon fluid migration through faulted cap rocks was determined by comparing the maximum connected thickness of cap rocks required for hydrocarbon fluid migration and the actual values, since cap rocks are important in the study of hydrocarbon fluid distribution in petroliferous basins based on its migration mechanism(s). The maximum connected thickness required was identified by comparing the cap rocks, fault displacement, and oil/gas distribution. The hydrocarbon fluid at the Putaohua reservoir migrated to the overlying Saertu and Heidimiao reservoirs in the Bayan Chagan Area, northern Songliao Basin. This was predicted to demonstrate the validity of the method. The results show that the adjusted Putaohua oil reservoir was distributed near the Talahai fault and Bayanchagan fault, rather than the Gulong sag in the southwest of the study area, where oil migrated vertically through the Sapu cap rocks to the overlying Saertu reservoir. Thick mudstone cap rocks in the second member o... [more]

GPS has become an attractive feature for geolocalization enabling asset tracking IoT devices. GPS satellite antennas radiate RHCP (right-hand circularly polarized) electromagnetic waves; thus, the typical antenna at the receiver is also RHCP. However, when the orientation of the receiving device is random, linear polarization antennas operate better in terms of TTFF (time to first fix). Through field measurements (urban and field) and considering different positions of the device in a vehicle, an RHCP microstrip patch antenna and a linear non-resonant antenna element called an antenna booster were compared. TTFF averaged for several positions was 7 s better for the linearly polarized antenna booster than for the microstrip RHCP patch antenna. The results demonstrate that the behavior of the linear polarization antenna booster technology is more robust in terms of TTFF to the arbitrary position of the IoT device while keeping a small size and simplicity.sdf

Hybrid donor extractants are a promising class of compounds for the separation of trivalent actinides and lanthanides. In this paper, we present a new ligand from the bipyridyl-dicarboxylic acid diamide family—N,N’-diethyl-N,N’-bis(2,4,5-trimethylphenyl)-[2,2’-bipyridine]-6,6’-dicarboxamide. The synthesis of N-ethyl-2,4,5-trimethylaniline from pseudocumene by selective acetylation is presented. The target ligand was obtained using this aminylene. Chemical synthesis of its complexes with Ln(NO3)3 and their spectroscopic analysis showed that the structure of the complexes is near to the corresponding structures of well-known di-methylated dianilides. A series of studies on the photophysical, complexing, and extraction properties of this ligand and its complexes were carried out. It was shown that the extraction system based on this ligand can selectively isolate americium from the solution of high-level waste imitator.

The origin of deep-water mounds has been a topic of debate in recent years. In this study, newly collected seismic data were employed to characterize the mounds within the Meishan Formation in the Qiongdongnan Basin and a novel model was proposed. The result showed that pervasive mounds and ‘V’-shaped troughs were alternately distributed at the top of the Meishan Formation. They appeared as elongated ridges flanked by similarly elongated gullies, with the trending parallel with the strike of the basinward slope. The mounded features were considered to be formed in response to the tectonically induced seabed deformation. The differential subsidence steepened the slope that was equivalent to the top of the Meishan Formation (ca. 10.5 Ma), which offered sufficient driving forces triggering the slope’s instability. Correspondingly, the uppermost deposits glided along a bedding-parallel detachment surface, creating a number of listric detachment faults that ceased downward to this surface.... [more]

Technology plays an essential role as climate change becomes a growing concern worldwide. This article aims to examine the influence that innovation exerts on climate change mitigation technology (CCMT) in the African and Asian mining sectors. Data were collected from the World Intellectual Property Organization mining database. We conducted a decomposition analysis of patent families between 2011 and 2020 based on the Logarithmic Mean Divisia Index (LMDI) method. Findings revealed that African countries do not devote their innovation efforts to adaptive technologies, resulting in a mismatch between mining and access to technologies as the scope of R&D narrows. In Asia, the drive for innovation and technological efficiency is a tool to prevent economic damage and legitimize technological benefits as solutions for climate change mitigation technology. This outcome calls on political, national, and international governments to bridge the innovation gap to trigger a real shift from innova... [more]

In this paper, variations in the normal component of the magnetic field BZ on the surface of Q195 steel specimens produced by simultaneous application of noncoaxial DC magnetic field and stress were studied by tensile tests. It was found that there was no shift in the direction of BZ variations when the specimens were magnetized parallel to stress, whereas the direction of BZ variations shifted a slight angle relative to the DC magnetic field when the specimens were magnetized perpendicular to stress. The amplitude of BZ increased with stress from 0 MPa to 120 MPa when the stress was parallel to the DC magnetic field. On the contrary, the amplitude of BZ decreased with stress from 0 MPa to 120 MPa when the stress was perpendicular to the DC magnetic field. The mechanisms underlying the experimental characteristics are also discussed. This research provides the possibility for quantitative inspection of the stress in ferromagnetic steels using surface magnetic field measurements.

Regular and reliable access to energy is critical to the foundations of a stable and growing economy. The Nigerian transmission network generates more electricity than is consumed but, due to unpredicted outages, customers are often left without electrical power for several hours during the year. This paper aims to assess the present reliability indices of the Nigerian transmission network, and to determine the impact of HVDCs on system reliability. In the first part of this paper, the reliability of the Nigerian transmission system is quantified by building a model in DIgSILENT PowerFactory and carrying out a reliability study based on data provided by the Nigerian transmission-system operator. Both network indices and load-point indices are evaluated, and the weakest points in the network are identified. In the second part of the paper, an HVDC model is built and integrated into the existing network at the locations identified by the reliability study. A comparative study using two d... [more]

In this study, the possibility of sintering industrial pressed uranium dioxide pellets using microwave radiation for the production of nuclear fuel is shown. As a result, the conditions for sintering pellets in an experimental microwave oven (power 2.9 kW, frequency 2.45 GHz) were chosen to ensure that the characteristics of the resulting fuel pellets meet the regulatory requirements for ceramic nuclear fuel, including the following: a density of about 10.44 g/cm3; a volume fraction of open pores of tablets of about 0.1%; an oxygen coefficient of no more than 2.002; hydrogen content of about 0.30 ppm; and the change in density after re-sintering on average no more than 1.16%.

LaMnO3 with perovskite structure is a SCR de-NOx catalyst with good performance at low temperatures. In this paper, the SCR reaction process on the 010 surface of LaMnO3 catalyst was studied by DFT method, to guide the development of catalysts and their effective application. The results obtained through research indicate that both E-R and L-H mechanisms exist on the catalyst surface. The NH3 molecule can be absorbed on L acid and then oxidized by lattice oxygen to form NH2. Then, NH2 can react with the NO molecule to form NH2NO and decompose to N2 and H2O. The NH3 can also be absorbed with hydroxyl to form NH4+, it can also react with NO to form NH2NO and then decompose. The NH4+ also can react with NO3− which is formed by NO oxidized when O2 is present, to participate in the rapid SCR process.

Many researchers have devoted themselves to the collision processes of binary droplets of the same liquid. However, the liquids used in their study were limited, and the phase diagram of the collision outcome was depicted in terms of the Weber and the non-dimensional impact parameter. In this research, the variety of liquid was broadened, and the phase diagram characterized by the Weber number and the Ohnesorge number for head-on collisions of immiscible drops was provided. First, a ternary flow model of binary collision of immiscible drops in quiescent ambient air was proposed. Second, the three-phase fluid interface was tracked and updated by iterating the VOF (Volume of Fluid) functions. The flow field was also updated with the PISO (Pressure-Implicit with Splitting of Operators) algorithm. Finally, the effects of the impact velocity and the viscosities of the liquids on the deformation degree of droplets were analyzed.

An experimental study was performed to investigate the characteristics of two different combustion instability modes in a swirl-stabilized combustor. The first is the eigenfrequency corresponding to the half-wave of the combustion chamber section, and the second is the quarter-wave eigenmode of the inlet mixing section. The purpose of this study is to understand the effects of the swirl number on each combustion instability mode and analyze their generalized characteristics. Premixed gases composed of hydrocarbon fuels (C2H4 and CH4) and air were burned by independently varying the experimental conditions. Three dynamic pressure transducers and a photomultiplier tube were installed to detect pressure oscillations and heat release fluctuations in the inlet and combustion chamber sections, respectively. A high-speed camera was used to capture the instantaneous flame structures. In the swirl-stabilized combustor, the bands of the dominant frequencies were strongly dependent on the swirl n... [more]

The research consisted of simulating the movement of a single vehicle in relation to the swarm leader on a square-shaped path, taking into account measurement errors characteristic of typical cheap navigation devices and the hydroacoustic system. The research showed that these methods allow for estimating position coordinates with an accuracy of about 0.5 m (RMS) in the case of a calibrated navigation system and about 3.6 m (RMS) in the case of a non-calibrated navigation system. It also showed that it can provide a higher accuracy of estimating position coordinates in terms of abeam angles of the swarm leader (relative bearing equal to approximately ±90°), as well as while ensuring minimizing systematic errors values and proper estimation of mean errors values concerning course and speed measurements.

To accurately study the drying characteristics of tobacco strips in the process of redrying, a discrete heaped physical model of tobacco strips is built. Based on this model, a convective drying multiphase porous media model of the heaped tobacco strips is established, which considers the binary diffusion and transport of vapor inside and outside the tobacco leaf. The model is solved using COMSOL Multiphysics, and the accuracy of the model is verified by experiments. The changes in hot air velocity, vapor and moisture content, and evaporation rate in heaped tobacco strips with different thicknesses are analyzed. The results show that: it is feasible to study the drying characteristics of tobacco strips in redrying using a discrete heaped model; there were significant differences in water content, evaporation rate, and temperature in different regions of heaped tobacco strips; the increase in heaping thickness will significantly reduce the uniformity of heat and mass transfer of tobacco... [more]

Many new HVAC power cable installations on wind farms, both on- and offshore, have long lengths. In contrast to traditional power cable connections of a few kilometers, the failures of those systems usually result in much higher repair and unsupplied energy costs. To support the quality assurance of newly installed cable systems as well as to create a sound basis for condition-based maintenance, this paper discusses the technical challenges of the field testing of long-length power cable systems using a damped AC testing method and also discusses the best practical applications for the testing and diagnosis of these wind farm HVAC cable systems.

It is evident from extreme weather patterns that climate change is impacting the whole world [...]

High-efficiency rock-breaking is a problem that has long been studied in the oil- and gas-drilling industry. The successful use of ultrasonic technology in related fields has prompted us to study how to introduce ultrasonic technology into rock-breaking in oil and gas drilling. This paper introduces and discusses the successful cases of ultrasonic breaking technology in related fields, summarizes the three basic forms of ultrasonic action on rocks, namely, resonance, impact and cavitation, expounds the factors and laws that affect ultrasonic-assisted rock-breaking, and summarizes the research results reported in recent years. It is believed that, at present, the application of ultrasonic-assisted rock-breaking technology in the oil- and gas-drilling industry still faces some problems and challenges: first, the downhole high-temperature and high-pressure conditions will affect the effect of ultrasonic-assisted rock-breaking, and the related mechanisms and research are not clear; second,... [more]

Quantifying fission product yield uncertainty contribution to reactor burnup calculation is an important aspect of pebble-bed High Temperature Gas-cooled Reactor (pebble-bed HTGR) uncertainty analysis. In this work, uncertainty propagation of fission product yield to pebble-bed HTGR burnup calculation is conducted. Uncertainty of fission product yields from four fissile isotopes, namely 233U, 235U, 239Pu and 241Pu, are considered. The stochastic sampling-based uncertainty analysis method is adopted and fission product yield covariance matrices are estimated from ENDF/B-VII.1. The covariance matrix for each fissile actinide is estimated based on the Bayesian method and fission product yields are assigned with log-normal distribution in the sampling process with the Latin Hypercube Sampling (LHS) method. Since the fission fraction from 239Pu plays an important role in fissions of fuels with high burnup value in pebble-bed HTGR, the fission product yield uncertainty contribution from 239P... [more]

Based on the previous study of a single medium model, the dual medium model for the fractured composite reservoir and the triple medium model for a fracture−cavity composite reservoir was established, respectively. The similarities and differences in the corresponding pressure dynamic curves of each model were analyzed, and the general model of a composite gas reservoir composed of different inner and outer zones was obtained. The general model can be more easily used in actual production, and the accuracy and practicability of the model were verified by case analysis.