The impact of adding H2O2 in the fuel stream on the structure of non-premixed opposed-flow NH3/O2 flames was investigated numerically using a verified computational tool and validated mechanism. The results illustrate the dual role of the added H2O2 within the fuel jet. A small amount of H2O2 within the NH3 stream acted as a fuel additive that enhanced the reaction rate via reducing the kinetic time scale. However, a novel flame structure appeared when the H2O2 mole fraction within the fuel stream increased to χH2O2 > 16%. Unlike the pure NH3/O2 flame, a premixed reaction zone was discerned on the fuel side, in which H2O2 reacts with NH3 and played the role of an oxidizer. Then, the remaining NH3 that survived premixed combustion continues reacting with O2 and forms a non-premixed flame. As a result of this structure, it was shown that the well-established conclusion of “near-equilibrium” non-premixed flame analysis in which the strain on the flame is determined by the momentum fluxes... [more]

The transfer capabilities of High-Voltage Overhead Lines (HV OHLs) are often limited by the critical power line temperature that depends on the magnitude of the transferred current and the ambient conditions, i.e., ambient temperature, wind, etc. To utilize existing power lines more effectively (with a view to progressive decarbonization) and more safely with respect to the critical power line temperatures, this paper proposes a Dynamic Thermal Rating (DTR) approach using IoT sensors installed on some HV OHLs located in different Italian geographical locations. The goal is to estimate the OHL conductor temperature and ampacity, using a data-driven thermo-mechanical model with the Bayesian probability approach, in order to improve the confidence interval of the results. This work highlights that it could be possible to estimate a space-time distribution of temperature for each OHL and an increase in the actual current threshold values for optimizing OHL ampacity. The proposed model is v... [more]

Electrification of transportation is gaining traction as a viable alternative to vehicles that use fossil-fuelled internal combustion engines, which are responsible for a major part of carbon dioxide emissions. This global turn towards electrification of transportation is leading to an exponential energy and power demand, especially during late-afternoon and early-evening hours, that can lead to great challenges that electricity grids need to face. Therefore, accurate estimation of Electric Vehicle (EV) charging loads and time of use is of utmost importance for different participants in the electricity markets. In this paper, a scalable methodology for detecting, from smart meter data, household EV charging events and their load consumption with robust evaluation, is proposed. This is achieved via a classifier based on Random Decision Forests (RF) with load reconstruction via novel post-processing and a regression approach based on sequence-to-subsequence Deep Neural Network (DNN) with... [more]

The receiver serves as a critical component in tower-type concentrated solar power plants. Responsible for light-heat conversion, the efficiency of the receiver significantly affects the overall performance of the power plant. In the current study, the thermal performance of external receivers was investigated. An experiment was set up similarly using the solar simulator to experimentally investigate the heat losses of a billboard receiver. A billboard-type external receiver was designed, fabricated, and experimented with. A solar simulator having seven xenon lamps characteristics similar to the sunlight spectrum was used to obtain heat flux at the surface of the receiver. Convection losses in the head-on wind direction were evaluated, along with the radiation losses. The thermal efficiency of the billboard receiver calculated experimentally was around 83.9%. Numerical simulations were also carried out to compare the results against the experimental data. A variation of ±5% observed be... [more]

Subcooled flow boiling was experimentally investigated in a horizontal annulus with a temperature-controlled boiling surface and transparent outer pipe facilitating visualization. Boiling occurs on a copper tube with a diameter of 12 mm in an annulus with a 2 mm gap. Refrigerant R245fa is used as a working fluid. The focus of this study is to explore the effect of heat flux variation on the boiling flow patterns at approximately constant inlet flow conditions of the working fluid (fixed mass flux and inlet fluid temperature). Subcooled flow boiling is recorded by a high-speed camera, images are analyzed by a neural network to determine the bubble size distributions and their variation with the heat flux. The experimental setup being a part of the laboratory THELMA (Thermal Hydraulics experimental Laboratory for Multiphase Applications) at the Reactor Engineering Division of Jožef Stefan Institute, analysis methods and measurement results are presented and discussed.

Load forecasting (LF) is an essential factor in power system management. LF helps the utility maximize the utilization of power-generating plants and schedule them both reliably and economically. In this paper, a novel and hybrid forecasting method is proposed, combining a long short-term memory network (LSTM) and neural prophet (NP) through an artificial neural network. The paper aims to predict electric load for different time horizons with improved accuracy as well as consistency. The proposed model uses historical load data, weather data, and statistical features obtained from the historical data. Multiple case studies have been conducted with two different real-time data sets on three different types of load forecasting. The hybrid model is later compared with a few established methods of load forecasting found in the literature with different performance metrics: mean average percentage error (MAPE), root mean square error (RMSE), sum of square error (SSE), and regression coeffic... [more]

Variability in solar irradiance has an impact on the stability of solar systems and the grid’s safety. With the decreasing cost of solar panels and recent advancements in energy conversion technology, precise solar energy forecasting is critical for energy system integration. Despite extensive research, there is still potential for advancement of solar irradiance prediction accuracy, especially global horizontal irradiance. Global Horizontal Irradiance (GHI) (unit: KWh/m2) and the Plane Of Array (POA) irradiance (unit: W/m2) were used as the forecasting objectives in this research, and a hybrid short-term solar irradiance prediction model called modified multi-step Convolutional Neural Network (CNN)-stacked Long-Short-Term-Memory network (LSTM) with drop-out was proposed. The real solar data from Sweihan Photovoltaic Independent Power Project in Abu Dhabi, UAE is preprocessed, and features were extracted using modified CNN layers. The output result from CNN is used to predict the targe... [more]

Zero-emission transport is a very important topic that is increasingly taken up by many institutions and research centers around the world. However, the zero-emissivity of the vehicle is quite a complex issue, which should be understood as not only the lack of emissions during the operation of the vehicle, but also the provision of clean energy to the vehicle. In this approach, charging the battery of an electric vehicle from renewable sources—a photovoltaic (PV) farm—and its operation can be considered as a totally zero-emission form of transport. The article presents a PV system containing two micro-installations with a capacity of up to 40 kWp each to supply electricity to two parts of the Lublin Science and Technology Park (LSTP) building. Thanks to the innovative monitoring system, it was possible to analyze the consumption and production as well as the effective use of electricity. Statistical analyses of consumption (charging the electric vehicle battery) and electricity product... [more]

Struts as an important structure in the combustion chamber of hypersonic flight vehicles to inject fuel into main flow face a severe thermal environment. Transpiration cooling is considered as a potential method to provide a thermal protection for struts. This paper presents a numerical investigation on transpiration cooling for a strut based on Darcy−Forchheimer model and the local thermal non-equilibrium model and analyzes the mechanism of transpiration cooling. A coolant film and a velocity boundary layer are formed on the strut surface and the shock wave is pushed away from the strut, which can effectively reduce the heat load exerted on the strut. The temperature difference between coolant and solid matrix inside the porous strut is analyzed, a phenomenon is found that the fluid temperature is higher than solid temperature at the leading edge inside the porous strut. As flowing in the porous medium, the coolant absorbs heat from solid matrix, and the fluid temperature is higher th... [more]

The standard of manual operation in smart grid, which require accurate manipulation, is high, especially in experimental, practice, and training systems based on virtual reality (VR). In the VR training system, data gloves are often used to obtain the accurate dataset of hand movements. Previous works rarely considered the multi-sensor datasets, which collected from the data gloves, to complete the action evaluation of VR training systems. In this paper, a vectorized graph convolutional deep learning model is proposed to evaluate the accuracy of test actions. First, the kernel of vectorized spatio-temporal graph convolutional of the data glove is constructed with different weights for different finger joints, and the data dimensionality reduction is also achieved. Then, different evaluation strategies are proposed for different actions. Finally, a convolution deep learning network for vectorized spatio-temporal graph is built to obtain the similarity between test actions and standard o... [more]

Scour risk assessment considering reaction force at foundation was proposed and applied to newly developed pentapod suction bucket support structures for a 5.5 MW offshore wind turbine under ultimate limit state environmental load. Scour hazard was obtained according to scour depth by using an empirical formula, which is the function of marine environmental conditions such as significant wave height, significant period, and current velocity. Fragility of the pentapod support structure was evaluated using the bearing capacity limit state criterion under ultimate limit state load case. Scour risk was assessed by combining the scour hazard and the fragility. Finally, scour risk of the developed pentapod suction bucket support structure under ultimate limit state has been assessed.

The traditional battery state of charge (SOC) estimation method, which is based on neural networks, directly uses terminal voltage and terminal current as the input data. Although it is convenient to implement, it produces a large estimation error when the current and voltage change drastically. To solve this problem, a new method, which uses a composite multiscale wavelet transform, is proposed to estimate the battery SOC. In the proposed method, a wavelet transform is applied to the input data, and this process obtains the approximate coefficients and detail coefficients of the input data at different scales. A neural network then uses these coefficients as inputs to estimate the SOC. The experimental results show that the proposed method can improve the accuracy of the battery SOC estimation without changing the neural network structure or algorithm.

Photovoltaic (PV) arrays and their electronic converters are subject to various environmental disturbances and component-related faults that affect their normal operations and result in a considerable energy loss. Therefore, it is ever demanding to design such closed-loop operating algorithms that tolerate faults, present acceptable performance, and avoid wear and tear in the systems. In this work, the core objective is to extract maximum power from a PV array subject to environmental disturbances and plant uncertainties. The system is considered under input channel uncertainties (i.e., faults) along with variable resistive load and charging stations. A neuro-fuzzy network (NFN)-based reference voltage is generated to extract maximum power while considering variable temperature and irradiance as inputs. Furthermore, the estimated reference is tracked by the actual PV voltage under two types of controllers: certainty-equivalence-based robust sliding mode (CERSMC) and certainty-equivalen... [more]

In this paper, a new method for the balancing of rotor-bearing systems supported on fluid film bearings is proposed. The influence coefficients necessary for balancing are calculated using a novel simulation method called the Numerical Assembly Technique. The advantages of this approach are quasi-analytical solutions for the equations of motion of complex rotor-bearing systems and very low computation times. The Numerical Assembly Technique is extended by speed-dependent stiffness and damping coefficients approximated by the short-bearing theory to model the behavior of rotor systems supported on fluid film bearings. The rotating circular shaft is modeled according to the Rayleigh beam theory. The Numerical Assembly Technique is used to calculate the steady-state harmonic response, influence coefficients, eigenvalues, and the Campbell diagram of the rotor. These values are compared to simulations with the Finite Element Method to show the accuracy of the procedure. Two numerical exampl... [more]

The paper discusses existing trends and prospects for decarbonization in the Commonwealth of Independent States (the CIS), an international organization that regroups Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Russia, Tajikistan, Turkmenistan, and Uzbekistan. The CIS occupies a significant share of Eurasia, representing a large share of global energy consumption and production with a corresponding carbon footprint. These countries and their decarbonization prospects are rarely discussed in the English-language scientific literature. This paper fills in this gap by offering a comprehensive analysis based on statistical data, policy documents, and scenario-based future projections. The results underline that revisiting Nationally Determined Contributions, increasing energy efficiency, and decoupling GDP growth from greenhouse gas emissions are essential to the implementation of the Paris Agreement. The future energy mix should include larger shares of renewable energy... [more]

In the current paper, a novel technique is represented to control the liquid petrochemical and petroleum products passing through a transmitting pipe. A simulation setup, including an X-ray tube, a detector, and a pipe, was conducted by Monte Carlo N Particle-X version (MCNPX) code to examine a two-by-two mixture of four diverse petroleum products (ethylene glycol, crude oil, gasoline, and gasoil) in various volumetric ratios. As the feature extraction system, twelve time characteristics were extracted from the received signal, and the most effective ones were selected using correlation analysis to present reasonable inputs for neural network training. Three Multilayers perceptron (MLP) neural networks were applied to indicate the volume ratio of three kinds of petroleum products, and the volume ratio of the fourth product can be feasibly achieved through the results of the three aforementioned networks. In this study, increasing accuracy was placed on the agenda, and an RMSE < 1.21... [more]

Predicting the status of particulate air pollution is extremely important in terms of preventing possible vascular and lung diseases, improving people’s quality of life and, of course, actively counteracting pollution magnification. Hence, there is great interest in developing methods for pollution prediction. In recent years, the importance of methods based on classical and more advanced neural networks is increasing. However, it is not so simple to determine a good and universal method due to the complexity and multiplicity of measurement data. This paper presents an approach based on Deep Learning networks, which does not use Bayesian sub-predictors. These sub-predictors are used to marginalize the importance of some data part from multisensory platforms. In other words—to filter out noise and mismeasurements before the actual processing with neural networks. The presented results shows the applied data feature extraction method, which is embedded in the proposed algorithm, allows f... [more]

The intermittent and uncertain properties of wind power have presented enormous obstacles to the planning and steady operation of power systems. In this context, as an effective technique to study wind power uncertainty, the development of an accurate wind speed scenario generation method is of great significance for evaluating the impact of wind power in the power system. In the case of several wind farms, accurate scenario generation involves precise acquisition of the correlation between wind speeds and the greatest retention of statistical properties of wind speed data. Under this goal, this research provided a new method for scenario development based on principle component (PC) and R-vine copula theories that incorporates the spatiotemporal correlation of wind speeds. By integrating with PC theory, this strategy avoids the dimension disaster induced by employing R-vine copula alone while taking benefit of its flexibility. The simulation results utilizing the historical wind speed... [more]

The energy industry, primarily based on the use of fossil fuels (e.g., coal and oil) is rapidly shifting toward renewable energy for securing sustainable resources. Thus, preparing for large wind power ramp events is essential to retain reliable and secure power systems. This study proposed a new statistical approach to predict wind power ramp events, and evaluated the performance of prediction. The empirical data, which is the observed wind power output data and wind speed data from Taebaek (South Korea) were used for analyzing ramp events and for evaluation. Based on the data analysis, a practical metric for evaluating the performance of wind power ramp events forecasting was developed and presented in detail. Notably, the accuracy of forecasting was evaluated through various metrics, whereas the normalized mean absolute error (NMAE) analysis demonstrated ≤ 10% values for all the analyzed months. In addition, a system review was conducted to check if the methodology suggested in this... [more]

This article aims to present changes in the use of electricity by service companies, resulting from regulations within the framework of increasing energy efficiency from the perspective of the implementation of the European Green Deal strategy. To achieve the above goal, the following research question was formulated: to what extent did the COVID-19 pandemic affect the implementation of energy transformation and electricity consumption among the surveyed group of recipients? It should be noted that, so far in the global environment, more and more electricity has been used every year, and this tendency is still continuous and growing. Therefore, in European Union countries, measures have been taken to balance demand and its rational use, resulting from the implementation of the European Green Deal strategy. According to the strategic goal of the indicated policy, EU countries are obliged to implement a sequence of actions enabling their transformation into a modern, resource-efficient,... [more]

Lithium-ion batteries exhibit a dynamic voltage behaviour depending nonlinearly on current and state of charge. The modelling of lithium-ion batteries is therefore complicated and model parametrisation is often time demanding. Grey-box models combine physical and data-driven modelling to benefit from their respective advantages. Neural ordinary differential equations (NODEs) offer new possibilities for grey-box modelling. Differential equations given by physical laws and NODEs can be combined in a single modelling framework. Here we demonstrate the use of NODEs for grey-box modelling of lithium-ion batteries. A simple equivalent circuit model serves as a basis and represents the physical part of the model. The voltage drop over the resistor−capacitor circuit, including its dependency on current and state of charge, is implemented as a NODE. After training, the grey-box model shows good agreement with experimental full-cycle data and pulse tests on a lithium iron phosphate cell. We test... [more]

To make a correct decision during normal and transient states, the signal processing for relay protection must be completed and designated the correct task within the shortest given duration. This paper proposes to solve a dc offset fault current phasor with harmonics and noise based on a Deep Neural Network (DNN) autoencoder stack. The size of the data window was reduced to less than one cycle to ensure that the correct offset is rapidly computed. The effects of different numbers of the data samples per cycle are discussed. The simulations revealed that the DNN autoencoder stack reduced the size of the data window to approximately 90% of a cycle waveform, and that DNN performance accuracy depended on the number of samples per cycle (32, 64, or 128) and the training dataset used. The fewer the samples per cycle of the training dataset, the more training was required. After training using an adequate dataset, the delay in the correct magnitude prediction was better than that of the part... [more]

The large fluctuations in charging loads of electric vehicles (EVs) make short-term forecasting challenging. In order to improve the short-term load forecasting performance of EV charging load, a corresponding model-based multi-channel convolutional neural network and temporal convolutional network (MCCNN-TCN) are proposed. The multi-channel convolutional neural network (MCCNN) can extract the fluctuation characteristics of EV charging load at various time scales, while the temporal convolutional network (TCN) can build a time-series dependence between the fluctuation characteristics and the forecasted load. In addition, an additional BP network maps the selected meteorological and date features into a high-dimensional feature vector, which is spliced with the output of the TCN. According to experimental results employing urban charging station load data from a city in northern China, the proposed model is more accurate than artificial neural network (ANN), long short-term memory (LSTM... [more]

Serving as a key component of the core engine, the high-load axial compressor is expected to have high performance, which determines several critical parameter levels of the aero-engine. The unsteady effect on the performance induced by the interaction among different rotors should not be ignored during the design of a high-load compressor. The interaction between R1 (the first rotor row) and R2 (the second rotor row) rotors of a transonic axial compressor was measured in detail using high-frequency pressure fluctuation sensors, aiming to reveal the evolution and distribution characteristics of the R1 sweep effect inside the R2 passage. The results show that near choke and design points, the interaction between the R1 oblique shock wave at the leading edge and the high-pressure region on the blade pressure side triggers the R1-2BPF (blade passing frequency) disturbance, which is different from the traditional harmonic of the blade wake disturbance. A ‘long tail’ flow structure, which i... [more]

In order to predict the circuit response of a Gas Discharge Tube (GDT) to an electromagnetic pulse, a “black box” model for a GDT based on a machine learning method is proposed and validated in this paper.Firstly, the machine learning model of the Elman neural network is established by taking advantage of the existing measurement data to dampen the sinusoid signal, and then the established model is adopted to predict the response waveform of an unknown injection current grade and frequency.Without considering the complex physical parameters and dynamic behavior of GDTs, the Elman neural network modeling method is simpler than the existing physical or Pspice model.Validation experiments show a good agreement between the predicted and the measured waveforms.