Sea wave energy is being increasingly regarded as one of the most promising sources of renewable energy. This paper deals with the modeling and simulation of an onshore wave energy converter system designed by UMBRA GROUP SpA. Several topics are addressed. Starting from the multibody modeling strategy, this paper delves more deeply into the mechanical efficiency evaluation of the ball-screw in the elastohydrodynamic lubrication regime, the core of the energy conversion process, as well as the thermal characterization of the power take-off module, based on the lumped-parameter and finite element method models. High values of ball-screw indirect efficiency have been observed, ranging from 73% to 97%; these results appear even more encouraging when compared to the performance of alternative energy-consuming technologies. Thermal analysis, on the other hand, provided a maximum temperature increase of 40 °C, allowing for the aversion of any structural collapse and the realistic identificati... [more]

Compression by shock waves is a specific way of compressing gases. It has been practically applied for many years in supersonic flying objects. The idea of using this method in rotary engines is extremely appealing because one disk can replace several or a dozen disks of an axial compressor, significantly reducing the weight and production costs of the engine and lowering the fuel consumption due to possible increased compression ratio. This paper presents a review of existing technical solutions and the results of published research devoted to the construction of shock wave compression rotary engines: patents, scientific publications describing various research methods, numerical calculations, and the experimental results of unusual technical solutions. The characteristic solutions and problems that arose during the implementation of these methods are presented and described. Judging from the presented overview, these have wide application possibilities, and an enormous intellectual a... [more]

Vertical axis wind turbines are an emerging and in-development wind energy technology which are characterized by their complicated aerodynamics. Detached flow conditions, which are typically developed at operational tip speed ratios, demand a rigorous characterization of the airfoils for an accurate prediction of the turbine performance. In this work, a custom-built, three-component external strain gauge balance, specifically developed for airfoil testing, is validated. The physical reasons responsible for discrepancies with reference data are also analyzed. Two- and three-dimensional flat plates, as well as the DU06-W-200 airfoil, are tested in a wind tunnel. Lift and drag coefficients and pitching moments are obtained for a wide angular range at Re = 200,000. The results are compared with data from the bibliography and CFD simulations, performed with the recently developed GEKO (generalized k-omega) turbulence model, achieving remarkable agreement. Instantaneous forces are also analy... [more]

Drying is a complex process of simultaneous heat, mass, and momentum transport phenomena with continuous phase changes. Numerical modelling is one of the most effective tools to mechanistically express the different physics of drying processes for accurately predicting the drying kinetics and understanding the morphological changes during drying. However, the mathematical modelling of drying processes is complex and computationally very expensive due to multiphysics and the multiscale nature of heat and mass transfer during drying. Physics-informed machine learning (PIML)-based modelling has the potential to overcome these drawbacks and could be an exciting new addition to drying research for describing drying processes by embedding fundamental transport laws and constraints in machine learning models. To develop such a novel PIML-based model for drying applications, it is necessary to have a fundamental understanding of heat, mass, and momentum transfer processes and their mathematica... [more]

The methods used in chemical engineering are strongly reliant on having a solid grasp of the thermodynamic features of complex systems. It is difficult to define the behavior of ions and molecules in complex systems and to make reliable predictions about the thermodynamic features of complex systems across a wide range. Deep learning (DL), which can provide explanations for intricate interactions that are beyond the scope of traditional mathematical functions, would appear to be an effective solution to this problem. In this brief Perspective, we provide an overview of DL and review several of its possible applications within the realm of chemical engineering. DL approaches to anticipate the molecular thermodynamic characteristics of a broad range of systems based on the data that are already available are also described, with numerous cases serving as illustrations.

Emissions from wood burning for heating in secondary homes or cabins is an important part in the development of high-resolution emissions in specific areas. Norway is used as case study as 20% of the national wood consumption for heating occurs in cabins. Our study first shows a method to estimate emissions from cabins based on traffic data to derive cabin occupancy, which combined with heating need allows for the spatial and temporal distribution of emissions. The combination of residential (RWC) and cabin wood combustion (CWC) emissions shows large spatial and temporal differences, and a temporally “cabin population” can in areas be orders of magnitude larger than the registered population. While RWC emissions have been steadily reduced, CWC have kept relatively constant or even increased, which results in an increase in the cabin share to total heating emissions up to 25−35%. When comparing with regional emission inventories, our study shows that the gradient between rural and urban... [more]

In recent years, there has been great interest in Wankel-type rotary engines, which are one of the most suitable power sources for unmanned aerial vehicle (UAV) applications due to their high power-to-size and power-to-weight ratios. The purpose of the present study was to investigate the potential of a hydrogen enrichment strategy for the improvement of the performance and reduction of the emissions of Wankel engines. The main motivation behind this study was to make Wankel engines, which are already very advantageous for UAV applications, even more advantageous by applying the hydrogen enrichment technique. In this study, hydrogen addition was implemented in a spark-ignition rotary engine model operating at a constant engine speed of 6000 rpm. The mass fraction of hydrogen in the intake gradually increased from 0% to 10%. Simulation results revealed that addition of hydrogen to the fuel accelerated the flame propagation and increased the burning speed of the fuel, the combustion temp... [more]

The smart city has been a growing utopia, a brilliant image of a city of the future, in the past twenty years. Since its birth, at the end of the previous century, several changes have been seen in urban areas, both aligned and detached from this concept. On the one side, digital implementation seems to be growing in all the major cities, especially in the service sector, which are experiencing a proliferation of new solutions, tools and modalities of interactions. On the other side, new concepts are rising such as the “digital twin”, the “15-minute city”, and the “metaverse city”, evidencing both the necessity to continuously innovate and reach higher levels of digitalization but also the need to focus on people’s life. This paper aims to provide a contribution to the understanding of the concept’s evolution at the forefront of climate change with the aim to detect the elements of innovation, focusing on implementation roadmaps and trends but also searching for evolutions in research... [more]

This article introduces a single-phase five-level multilevel inverter based on six switches and two transformers. The proposed converter requires a single dc input source with low voltage. The disposition of switches makes it possible to build the converter with a transistors six-pack module off-the-shelves, traditionally used to build three-phase inverters, which simplifies the manufacturing process. The converter increases the voltage with two transformers; for that reason, it does not require an auxiliary step-up converter. The use of transformers (with the transformer’s turns ratio) allows for using the same topology for several input voltage levels. To verify the operation of the proposed multilevel inverter, a computer-based simulation was performed with PSIM, a software that considers parasitic components. The results show that the proposed converter can work properly.

Undersaturated oil viscosity is one of the most important PVT parameters to be measured and/or predicted in a fluid sample. Since direct experimental measurements are expensive and time-costly, prediction methods are essential. In this work, viscosity data from more than five hundred fluid reports are utilized, and all correlation methods available in the literature and implemented in commercial software for reservoir and production engineering calculations, including fracked systems, are evaluated against the dataset. The results of this work are intended to set up workflows that give insight as to which method should be selected when running flow simulations, with emphasis on complex simulations such as in the case of EOR. The developed workflows provide the optimal choice of the viscosity correlation for the case of distinct viscosity ranges, as well as when overall performance is sought. A surprising result is that one of the oldest known correlations from the literature gives the... [more]

Direct contact heat exchangers can be smaller, cheaper, and have simpler construction than the surface, shell, or tube heat exchangers of the same capacity and can operate in evaporation or condensation modes. For these reasons, they have many practical applications, such as water desalination, heat exchangers in power plants, or chemical engineering devices. This paper presents a comprehensive review of experimental and numerical activities focused on the research about direct condensation processes and testing direct contact condensers on the laboratory scale. Computational Fluid Dynamics (CFD) methods and CFD solvers are the most popular tools in the numerical analysis of direct contact condensers because of the phenomenon’s complexity as multiphase turbulent flow with heat transfer and phase change. The presented and developed numerical models must be carefully calibrated and physically validated by experimental results. Results of the experimental campaign in the laboratory scale... [more]

Asal rift is an aerial rift segment resulting from the westward propagation of the Aden ridge into the Afar Depression. Geothermal manifestations such as hot springs and fumaroles, fault creep, conductivity anomaly, and high geothermal gradient were observed both at the surface and in the subsurface. Despite many scientific works conducted in Asal to understand the rifting mechanisms, the hydrothermal fluid circulation still needs to be evaluated since it is based on simplified conceptual models. To further contribute and progress toward a quantitative evaluation of fluid circulation, a 2D numerical model perpendicular to the rift axis was developed with the objective of better understanding the role of subsurface anisotropy in fluid flow and heat transfer in the Asal rift. Numerical modeling of multiphase flow and heat transfer was carried out with an equivalent porous medium intersected by fault zones having greater permeability. Horizontal anisotropic permeability and magmatic fluid... [more]

High-speed EMUs (electric multiple-units) frequently pass through the phase-separation zone during operation. Overvoltage generated during the operation of the vehicle-mounted circuit breaker has a long duration and high waveform steepness, which accelerates the service life of the vehicle-mounted equipment and is likely to cause insulation failures. For the above-mentioned problems, the operating overvoltage characteristics of high-speed EMU were obtained by traction substation-catenary-EMUs system (SCES) analysis and experiments, thus deriving the influences of the closed phase angle and the residual magnetism of the vehicle-mounted transformer on operating overvoltage. The results showed that the voltage phase of the catenary significantly affected the operating overvoltage, and the closed switching overvoltage was small at 0−40°, 140−210° and 320−350°. The voltage on the primary side of the vehicle-mounted transformer was 60.78 kV, with the transient impact of high-frequency oscill... [more]

This paper proposes an alternative multiconductor transmission line model that combines the folded line equivalent with the modal transformation. The folded line equivalent decomposes the nodal admittance matrix of a transmission line into its open-circuit and short-circuit contributions. These contributions are fitted to rational functions, which are associated with Norton equivalent circuits based on their state space models. The proposed model uses an orthogonal matrix to transform voltages and currents from the phase domain to the folded line equivalent domain and vice versa. Because the transformation matrix is orthogonal, we represent it using ideal transformers in simulation software. First, we use a circuit representation of Clarke’s matrix to decompose a transmission line into its modes. Then, each mode is decomposed into its open-circuit and short-circuit contributions using a circuit implementation of the proposed matrix. The proposed approach can accurately represent short... [more]

Porosity and permeability alteration due to the thermo-poro-elastic stress field disturbance from the cold fluid injection is a deciding factor for longer, more economic, and safer heat extraction from an enhanced geothermal system (EGS). In the Soultz-sous-Forêts geothermal system, faulted zones are the main flow paths, and the resulting porosity−permeability development over time due to stress reorientation is more sensitive in comparison with the regions without faulted zones. Available operational and field data are combined through a validated numerical simulation model to examine the mechanical impact on the pressure and temperature evolution. Results shows that near the injection wellbore zones, permeability and porosity values are strongly affected by stress field changes, and that permeability changes will affect the overall temperature and pressure of the system, demonstrating a fully coupled phenomenon. In some regions inside the faulted zones and close to injection wellbore... [more]

The paper presents a new approach to designing the stator of a multistage centrifugal pump, which has a simple structure, satisfactory operating parameters, and is easy to manufacture. The stator is distinguished by its lack of a classic diffuser part, with the shape of its crossover being similar to a segment of a spherical surface. This solution was patented in 1989, but to date it is not well known and practically not used. The paper attempts to identify the flow phenomena in such a stator and also to examine the impact of the design features of the stator on the pump’s operating parameters. Both experimental methods and numerical modelling were used in the research.

The Magnetotelluric (MT) method is a widely used and effective method of exploring geothermal resources because it can reveal geological information at a great depth and is cost effective. In order to further improve the reliability and rationality of MT data interpretation, MT responses for a typical hydrothermal system and a hot dry rock (HDR) and partial melting system are investigated by a finite-element (FE) forward modeling approach based on unstructured tetrahedral grids that can handle with complex-shaped geothermal systems. These two geothermal models, designed by the 3ds Max software, are comprised of a clay cap, a reservoir, and a heat source, and are discretized into tetrahedral elements by TetGen software. The results show that the apparent resistivities at the broadband of frequencies are mainly affected by the shallow low-resistivity clay cap due to its strong shielding effects, and the induction arrows effectively reflect the boundary of the clay cap. The conductive hea... [more]

Identification of harmonic sources contributing to harmonic distortion, and characterization of harmonic current injected by them, are crucial tasks in harmonic analysis of modern power systems. In this paper, these tasks are addressed based on the permissible current limits recommended by IEEE 519 Standard, with a determination of whether or not injected harmonics are within these limits. If limits are violated, the extent of the violations are characterized to provide information about harmonic current levels in the power system and facilitate remedial actions if necessary. A novel feature extraction method is proposed, whereby each set of harmonic measurements in a power system are transformed into a unique RGB image. Harmonic State Estimation (HSE) is discretized as a classification problem. Classifiers based on deep learning have been developed to subsequently locate and characterize harmonic sources. The approach has been demonstrated effectively both on the IEEE 14-bus system, a... [more]

A Cascadia Subduction Zone (CSZ) earthquake will cause widespread damage to numerous lifelines and infrastructure along the northern US west coast. The goal of the presented research is to provide a bottom up estimate of the impact on and subsequent recovery of a Cascadia Subduction Zone earthquake on the US western grid to supplement and enhance the expert opinion estimates provided to date. The scope is limited to only consideration of shaking damage to utility substation equipment components of a power system model. The analysis utilizes probabilistic models of damage and recovery for substation power system assets, along with graph techniques for modeling connectivity, and Monte Carlo quasi steady state power flow solutions. The results show that a conservative estimate of the initial damage and loss of load is approximately 4000 MW, with a recovery estimate of 230 days.

A hydrodynamic wind−wave combined power generation system is a new type of energy device that uses wind and ocean current energy to generate electricity. In this paper, the hydrodynamics of a wind−wave combined power generation system was simulated in Fluent. The fluid−structure coupling simulation of the vortex vibration of the cylindrical oscillator was realized using UDF and dynamic mesh technology. The Vortex-Induced Vibration (VIV) characteristics of the cylindrical oscillator were analyzed, and the reliability of the numerical simulation method was verified by comparing the amplitude and trajectory of the eddy-excited vibration with the classic experiments of Jauvtis and Williamson. The VIV characteristics of cylindrical oscillators with different mass ratios were studied in terms of vibration response, motion trajectory, and the streamwise equilibrium position. The effect of the mass ratio on the hydrodynamics of a wind−wave combined power generation system was simulated using s... [more]

Enhancing the performance of photovoltaic (PV) systems has recently become a key concern because of the market demand for green energy. To obtain the most possible power from the solar module, it is imperative to allow the PV system to operate at its maximum power point (MPP) regardless of the climatic conditions. In this study, a comparison of distinctive Maximum Power-Point Tracking (MPPT) techniques is provided, which are Perturb and Observe (P&O) and Modified Variable Step-Size P&O, as well as Incremental Conductance (INC) and Modified Variable Step-Size INC, using a boost converter for two types of solar panels. Using MATLAB software, simulations have been performed to assess the efficiency of the solar module under several environmental conditions, standard test conditions (STCs), and sudden and ramp variations in both solar irradiance and temperature. The output power efficiency, time response, and steady-state power oscillations have all been taken into account in this study. T... [more]

Iran is one of the most energy-consuming countries, especially in the construction sector, and more than 40% of its energy consumption is in the construction sector. Therefore, considering the very high potential of Iran in the field of solar energy, the need to pay attention to providing part of the energy required by buildings by solar energy seems necessary. The study of the effect of climate on the performance of a BIPV has not been done in Iran so far. Also, the use of ranking methods using the weighting of parameters affecting the performance of BIPV has not been done so far. The purpose of this study is to investigate the power supply of BIPV connected to the grid in the eight climates of Iran. Technical−economic−environmental energy analyses were performed by HOMER 2.81 software. In order to study different types of BIPV, four angles of 0°, 30°, 60°, and 90° were considered for the installation of solar cells. The effective output parameters of HOMER software were weighted by t... [more]

The article discusses the process of designing and testing as well as their results, carried out in order to increase the efficiency of axial fans, implemented as part of the European project INESI. Modifications of existing solutions based on rapid prototyping methods were presented. Scanning, FEM and CFD numerical calculations and 3D printing were used for that purpose. Rapid prototyping involved the use of a steel blade base and 3D-printed complex aerodynamic shapes that were bonded to create completely new blades. After their installation on the new rotor, enabling the angle of attack adjusting, a number of verifying tests of the fan were carried out. The solution was successfully tested and the results are discussed in the article.

The timescale of the energy-release process of an energy storage system has put forward higher requirements with the increasing proportion of new energy power generation in the power grid. In this paper, a new type of compressed-air energy storage system with an ejector and combustor is proposed in order to realize short-timescale and long-timescale energy-release processes under the non-supplementary combustion condition and ejector supplementary combustion condition, respectively. A simulation model of the new system is established in APROS software. The results of this study show that the new system can realize continuous power output when energy storage and energy release operate simultaneously, and especially when the ejector coefficient is 0.8 and burner thermal power is 10 MW, the power-generation time is 12.45 h and the total generated power is 140,052 kW∙h, which are 15.6 and 17.5 times greater those of the short-timescale condition, respectively. In summary, the compressed-ai... [more]

A numerical procedure was developed to determine a variable-pitch law that maximized the performance of a vertical-axis wind turbine (VAWT). The methodology was based on the determination, for each blade, of the angle of attack maximizing the stationary aerodynamic efficiency at prescribed azimuthal positions. The angles of attack were determined by means of a panel method with a low computational effort, and the methodology was implemented in Matlab® software (version R2021a) allowing us to achieve in real time a variable-pitch law suitable for the turbine geometry. The variable pitch law was validated by considering its effect on the torque of a 2D model of an H-Darrieus turbine. U-RANS analyses were carried out with a K−ωSST model and a sliding-mesh technique was used to prescribe the blade motion around the shaft and pitch motion. Results showed how the variable-pitch law delayed the dynamic stall and improved the aerodynamic performance considerably.