MnFe2O4 ferrite nanoparticle was synthesized via the sol−gel method, and structural, morphology and magnetic characteristics were investigated. X-ray diffraction analysis showed that the synthesized sample was in a single phase with a spinel-ferrite-like structure (space group Fd-3m). The scanning electron microscopy displayed homogenous spherical grains with an agglomeration of the particles. The chemical composition determined by energy-dispersive spectroscopy shows the absence of any impurities. To understand the role of magnetic interaction in MnFe2O4 spinel ferrites, the structural and magnetic properties of MnFe2O4 have been explored theoretically. Based on the first-principles methods via density functional theory and Monte Carlo simulations, the magnetic hysteresis cycle has been plotted. Using the generalized gradient and GGA-PBE approximation in the full-potential linearized augmented plane wave (FP-LAPW) method, the exchange coupling interactions between magnetic elements an... [more]

Thermochemical heat storage has attracted significant attention in recent years due to potential advantages associated with very high-energy density at the material scale and its suitability for long-duration energy storage because of almost zero loss during storage. Despite the potential, thermochemical heat storage technologies are still in the early stage of development and little has been reported on thermochemical reactors. In this paper, our recent work on the charging and discharging behavior of a fixed-bed thermochemical reactor is reported. Silica gels were used as the sorbent for the experimental work. An effective model was established to numerically study the effect of different charging conditions on the discharging behavior of the reactor, which was found to have a maximum deviation of 10.08% in terms of the root mean square error compared with the experimental results. The experimentally validated modelling also showed that the discharging temperature lift increased by 5... [more]

To investigate the influence of thermal effects on the hydrogen desorption performance of the metal hydride hydrogen storage system, a two-dimensional numerical model was established based on a small metal hydride hydrogen storage tank, and its accuracy was verified by the temperature variations in the reaction zone of the hydrogen storage tank during hydrogen desorption. In addition, the influence of the heat transfer medium on the heat and mass transfer performance of the hydrogen desorption reaction was analyzed. An external heat transfer bath was added to simulate the thermal effect of the model during the hydrogen desorption reaction. The temperature and type of heat transfer medium in the heat transfer bath were modified, and the temperature and reaction fraction variations in each zone of the hydrogen storage model were analyzed. The results showed that under heat transfer water flow, the reaction rate in the center region of the hydrogen storage tank was gradually lower than th... [more]

A model different from the traditional WEC, known as the flexible wave energy converter (fWEC), is numerically modeled in this paper. The fWEC is believed to be more efficient and has a greater range of operation when compared with the conventionally rigid WEC. A fully coupled fluid−structure interaction (FSI) tool is developed for the research performed in this paper. This tool is able to accommodate the dynamic interaction between the flexible membrane structure of the fWEC and the surrounding fluid. In this research, both linear-elastic and hyper-elastic materials are examined for their use in the fWEC. The fluid flow surrounding the fWEC is solved by a computational fluid dynamics (CFD) method. The deformation of the hyper-elastic structure within the fWEC is modeled using a finite element analysis method (FEA). Both the hyper-elastic material of the fWEC and the free surface wave contribute to the overall nonlinearity of the numerical simulation. To tackle this problem, a robust c... [more]

Solar ponds are characterized by high storage capacity and the ability to provide a stable and continuous power source. Careful selection of the extraction rate helps to maintain supply temperature in a range suitable for the operation of an absorption unit. This study proposed a system in which a solar pond is coupled with an absorption chiller to investigate the resulting advantages. The chiller is cooled by using water of the upper convective zone, which ensures that the limit of deterioration of its performance is not reached and eliminates the need for an expensive cooling system. The key parameters in terms of ambient temperature, solar radiation, pond specifications, and cooling and refrigeration temperatures are investigated to optimize the proposed system design. The prediction of the model showed good agreement with the experimental results. By choosing the appropriate place to implement the system, such as the Dead Sea area, which enjoys favorable climatic conditions, it was... [more]

Icing is a severe problem faced by wind turbines operating in cold climates. It is affected by various fluctuating parameters. Due to ice accretion, a significant drop in the aerodynamic performance of the blades’ airfoils leads to productivity loss in wind turbines. When ice accretes on airfoils, it leads to a geometry deformation that seriously increases turbulence, particularly on the airfoil suction side at high angles of attack. Modeling and simulation are indispensable tools to estimate the effect of icing on the operation of wind turbines and gain a better understanding of the phenomenon. This paper presents a numerical study to assess the effect of surface roughness distribution, along with the effect of two turbulence models on estimating wind turbine airfoils’ aerodynamic performance losses in the presence of ice. Aerodynamic parameter estimation was performed using ANSYS FLUENT, while ice accretion was simulated using ANSYS FENSAP-ICE. The results using the adopted modeling... [more]

Floating solar energy is an industry with great potential. As the industry matures, floating solar farms are considered in more challenging environments, where the presence of waves must be accounted for in mismatch studies and fatigue and mechanical considerations regarding electrical cables and mooring lines. Computational modelling of floating solar islands is now a critical step. The representation of such islands on industry-validated software is very complex, as it includes a large number of elements, each interacting with its neighbours. This study focuses on conditions with small waves (amplitude of <1 m) that are relevant to sheltered areas where generic float technologies can be utilized. A multi-body island composed of 3 × 3 floats is modelled in OrcaFlex. A solution to model the kinematic constraint chain between floats is presented. Three different modelling solutions are compared in terms of results and computation time. The most accurate model includes a multi-body co... [more]

The paper shows the use of novel modelling techniques adapted from ironmaking in the pyrometallurgical process of zinc production. Firstly, regarding the purpose to determine the boundary conditions of reduction processes taking part in the working volume of an Imperial Smelting Furnace (ISF), a deep thermochemical analysis was conducted. On this basis and using Ramm’s principles of direct and indirect reduction optimal share, the fuel rate minimization model was built. The model’s leading role is minimizing coke consumption in the ISF while maintaining the thermal state of the furnace at the correct level. In addition, the proposed presentation of the ISF thermal state shows in a unified way all the shortcomings in the correct process operation. Verification in real conditions on the ISF in Miasteczko Śląskie shows that model implementation can bring tangible benefits. Coke savings can reach over 30 kg per tonne of raw zinc.

Australia’s electricity networks are experiencing low demand during the day due to excessive residential solar export and high demand during the evening on days of extreme temperature due to high air conditioning use. Pre-cooling and solar pre-cooling are demand-side management strategies with the potential to address both these issues. However, there remains a lack of comprehensive studies into the potential of pre-cooling and solar pre-cooling due to a lack of data. In Australia, however, extensive datasets of household energy measurements, including consumption and generation from rooftop solar, obtained through retailer-owned smart meters and household-owned third-party monitoring devices, are now becoming available. However, models presented in the literature which could be used to simulate the cooling energy in residential homes are temperature-based, requiring indoor temperature as an input. Temperature-based models are, therefore, precluded from being able to use these newly av... [more]

Elastocaloric cooling is considered an environmentally friendly future alternative to vapor-compression technology. Recently, a shell-and-tube-like elastocaloric regenerator loaded in compression has demonstrated record-breaking heat-pumping performance and fatigue-resistant operation. The aim of this work is thus to present a new 1D numerical model to simulate and optimize the operation of an elastocaloric regenerator with a shell-and-tube-like design. In the first part of this work, the superelastic and elastocaloric properties of a single NiTi tube, which serve as input data for the numerical model, were determined through experimental characterization and phenomenological modeling. In the second part, the results of the numerical model were compared with the experimentally obtained results. Relatively good agreement was found regarding the temperature span, cooling and heating power, and COP values, which indicates that the developed numerical model could be used for accurate optim... [more]

Proton exchange membrane fuel cells (PEMFCs) have been recognized as a promising power generation source for a wide range of automotive, stationary, and portable electronic applications. However, the durability of PEMFCs remains as one of the key barriers to their wide commercialization. The membrane electrode assembly (MEA) as a central part of a PEMFC, which consists of a proton exchange membrane with a catalyst layer (CL) and gas diffusion layer (GDL) on each side, is subject to failure and degradation in long-running and cycling load conditions. The real-time monitoring of the degradation evolution process through experimental techniques is challenging. Therefore, different numerical modeling approaches were proposed in the literature to assist the understanding of the degradation mechanisms in PEMFCs. To provide modeling progress in the addressed field, this paper briefly discusses the different degradation mechanisms occurring in the MEA. In particular, we present a detailed revi... [more]

Thanks to technological advances, the number of large-scale ESS applications is increasing in power systems. Therefore, the need for an ESS model to analyze the effect through simulation has also increased. In this study, an ESS analysis model was developed for transmission-level power-system analysis. The developed model has a relatively uncomplicated configuration compared to the previous model. The ESS model was developed in a form that can be exploited in the PSS®E, commercial power-system analysis program. The programming language FORTRAN was used for model development. A detailed process and necessary data for the model development are described. The operation of the developed ESS model was verified through simulation using two test systems. The results of this study can be used for power-system analysis and as reference material for model development.

In recent years, the explosion of renewable energy sources, the increase in the demand for electrical energy, and several improvements in related technologies have fostered research in many relevant areas of interest [...]

Modern low-voltage distribution systems necessitate solar photovoltaic (PV) penetration. One of the primary concerns with this grid-connected PV system is overloading due to reverse power flow, which degrades the life of distribution transformers. This study investigates transformer overload issues due to reverse power flow in a low-voltage network with high PV penetration. A simulation model of a real urban electricity company in Ghana is investigated against various PV penetration levels by load flows with ETAP software. The impact of reverse power flow on the radial network transformer loadings is examined for high PV penetrations. Using the least squares method, simulation results are modelled in Excel software. Transformer backflow limitations are determined by correlating operating loads with PV penetration. At high PV penetration, the models predict reverse power flow into the transformer. Interpolations from the correlation models show transformer backflow operating limits of 7... [more]

At present, computational fluid dynamics (CFD) is an inherent component of the development procedure of a majority of technological processes involving fluid flows and/or heat and mass transfers. Practicing engineers and investigators employ different commercial CFD software, open-source codes and even develop their own computational codes (in house) for solving tasks, requiring accounting for nonstandard effects.

This work shows an alternative method to determine the Voltage Unbalance Factor in a power grid by using both the mean value of the line voltages and Current Unbalance Factor in induction motors. Twenty unbalanced voltage points on three induction motors were used in order to compare the two methods. The influence of the measurement error of both the voltmeters and the ammeters on the resulting Voltage Unbalance Factor was studied, and the validation was made with laboratory data for one of the three motors analyzed, in addition to the simulations carried out. The proposed Voltage Unbalance Factor was compared with the most typical method in the standards to obtain this factor, showing that the proposed factor has a better approach than the standard factor to determine the value of the Voltage Unbalance Factor in an unbalanced power system.

Recent advancements in the Internet of Things and Machine Learning techniques have allowed the deployment of sensors on a large scale to monitor the environment and model and predict individual thermal comfort. The existing techniques have a greater focus on occupancy detection, estimations, and localization to balance energy usage and thermal comfort satisfaction. Different sensors, actuators, and analytic data methods are often non-invasively utilized to analyze data from occupant surroundings, identify occupant existence, estimate their numbers, and trigger the necessary action to complete a task. The efficiency of the non-invasive strategies documented in the literature, on the other hand, is rather poor due to the low quality of the datasets utilized in model training and the selection of machine learning technology. This study combines data from camera and environmental sensing using interactive learning and a rule-based classifier to improve the collection and quality of the dat... [more]

The global trend is constantly increasing investments in strategic sectors of the economy, for example the electric power industry, which, in many countries, is becoming diversified and dispersed due to the multitude of entities investing in energy production and renewable resources, which leads to an increase in the heterogeneity of investment decisions. There is an urgent need to control the movement of investments, budget funds, as well as their development in the process of implementing investment programs of energy companies. The control of the movement of investments is the most promising direction of studying the subject of finance and audit. The increasing volume of public and private targeted investments in the energy sector and the lack of control over the effectiveness of investment projects (since each program contains several thousand lists of projects) necessitated the introduction of additional regulation of budget spending. The development of a mathematical apparatus fo... [more]

Electric vehicles (EVs) are a promising option to reduce air pollution and shipping costs, especially in urban areas. To provide scientific guidance for the growing number of logistics companies using EVs, we investigated an electric-vehicle-routing problem with simultaneous pickup and delivery that also considers non-linear charging and load-dependent discharging (EVRPSPD-NL-LD). The objective was to minimize the total number of EVs and the total working time, including travel time, charging time, waiting time, and service time. We formulated the problem as a mixed integer linear program (MILP), and small-size problems could be solved to optimality in an acceptable amount of time using the commercial solver IBM ILOG CPLEX Optimization Studio (CPLEX). In view of the fact that the problem is NP-hard, an adaptive large neighborhood search (ALNS) metaheuristic method was proposed to solve large-size problems. Meanwhile, new operators and a time priority approach were developed to provide... [more]

The performance of air conditioning systems deteriorate due to the natural aging and wear caused by operating the devices. This is termed “aging degradation,” and it results from a lack of appropriate maintenance which accelerates the degree of performance degradation. The performance degradation of an air conditioning system can cause problems such as increased energy consumption, deteriorated indoor heating environment, and shortened lifespan of air conditioning equipment. To prevent such problems, it is important to establish a long-term maintenance plan to recover degraded performance, such as predicting an appropriate maintenance time by identifying the real-time performance degradation rate based on a system’s operation data. In this study, the performance degradation rate, according to the operating time, was estimated using long-term operation data for devices constituting a heat source system, and the effect of performance degradation of the heat source system’s operation and... [more]

This paper presents a characteristic analysis and experimental verification for predicting the electromagnetic losses in high-speed permanent magnet synchronous motors. To predict the operating characteristics (such as speed and input current), dynamic modeling is conducted that combines models for the space vector pulse width modulation (SVPWM) inverter and high-speed permanent magnet synchronous motor (HPMSM). By applying the predicted harmonic currents to the electromagnetic analysis, DC and AC copper losses of the stator winding, and eddy current loss of the rotor sleeve and rotor permanent magnet, are comprehensively analyzed using the finite element (FE) method. In particular, by analyzing the magnetic field behavior of magnetic flux density according to harmonics, a core loss analysis technique was presented. The validity of the hybrid analysis, which combines the stator copper loss and rotor eddy current loss derived from the FE analysis and the proposed core loss analysis, was... [more]

With more stringent IEC energy efficiency standards, electrical machine industry increasingly focuses on new motor technologies. Amongst others, the line-start permanent magnet synchronous machine (LSPMSM) is considered as an attractive alternative to induction machine, especially for low power and fixed-speed applications. However, the design of LSPMSMs is rather complex as both steady-state and transient synchronization performances need to be considered. The synchronization capability determination of a LSPMSM design usually relies on time-consuming transient finite-element simulations, which is impractical for use in an iterative design optimization process. This paper compares and evaluates various existing analytical synchronization analysis methods in an attempt to identify most suitable equations and methods for fast synchronization analysis. Using the selected methods, a software tool is developed that can seamlessly work with ANSYS Electronics Desktop to perform rapid transie... [more]

The present study established two different models based on the convolutional neural network (CNN) and the encoder−decoder (ED) to predict the characteristics of the flow and heat transfer around the NACA sections. The established CNN predicts the aerodynamic coefficients and the Nusselt number. The established ED model predicts the velocity, pressure and thermal fields to explain the performances of the aerodynamics and heat transfer. These two models were trained and tested by the dataset extracted from the computational fluid dynamics (CFD) simulations. The predictions mostly matched well with the true data. The contours of the velocity components and the pressure coefficients reasonably explained the variation of the aerodynamic coefficients according to the geometric parameter of the NACA section. In order to physically interpret the heat transfer performance, more quantitative and qualitative information are needed owing to the lack of the correlation and the resolution of the th... [more]

Building-integrated photovoltaic (BIPV) façades are a promising technique for improving building energy performance. This study develops energy simulation models of different photovoltaic-integrated shading devices (PVSDs) in single-story and multi-story office buildings. A cross-region study in China is carried out to explore the energy performance of PVSDs in five climate zones. The shading effect of the upper PVSDs is taken into account. The results show that (1) PVSDs can be applicable in hot and cold climates; shading effects lead to a notable difference in the optimal PVSDs style. The average comprehensive energy saving ratios of different PVSDs ranged from 16.12% (fixed PV louvres in the vertical plane) to 51.95% (lower single panel). The most rewarding PVSDs are for single-story buildings in Kunming and the least suitable are for multi-story buildings in Guangzhou. (2) In climate zones with little air-conditioning energy consumption, avoiding considerably increased lighting con... [more]

Cyclic supercritical multi-thermal fluid stimulation (CSMTFS) is a novel technology that can efficiently recover heavy oil, while the heating effect, production and heat loss characteristics of CSMTFS have not been discussed. In this study, a physical simulation experiment of CSMTFS is conducted with a three-dimensional experimental system. The results of the study indicate that the whole process of CSMTFS can be divided into four stages, namely, the preheating stage, production increase stage, production stable stage and production decline stage, of which the production stable stage is the main oil production stage, and the production decline stage is the secondary oil production stage. In the first two stages of the CSMTFS process, there is no supercritical multi-thermal fluid chamber, and only a relatively small supercritical multi-thermal fluid chamber is formed in the last stage of the CSMTFS process. Out of the supercritical multi-thermal fluid chamber, supercritical water in the... [more]