The aim of this study was to identify the preferences of final purchasers regarding the environment of cooperation with offerors and the benefits of cooperation, as well as to identify dependencies between two groups of preferences, taking into account the age of purchasers. The results of an analysis of the global literature on the subject indicate that so far these issues have not been studied, either in relation to the energy market or other areas of the consumer market. Therefore, we can talk about a cognitive and research gap in this area. In order to reduce the gap, seven research hypotheses were formulated and primary research was carried out on 1196 adult representatives of final purchasers in Poland to verify the hypotheses. The collected data were subjected to quantitative analysis, the results of which made it possible to state that most respondents preferred the parallel use of the online and offline environments as a place of interaction with offerors. More than half of th... [more]

A fire can pose a significant threat to a building’s occupants and leads to property damage. The burning characteristics usually determine the severity of the accident. Environments in high-altitude areas feature low oxygen content and ambient pressure, which can influence the burning characteristics of combustibles. In this paper, a series of field experiments were conducted to investigate the burning characteristics of gasoline at different altitudes considering heat release rate (HRR), flame height, and smoke release rate. Results show that the combustion process can be divided into three stages: initial stage, stable stage, and attenuation stage. Lower oxygen content and ambient pressure reduce the HRR; for example, the HRR at an altitude of 4150 m is nearly half at an altitude of 500 m, contributing to a lower smoke release rate. The HRR is proportional to 1.3 power of atmospheric pressure, and a fitting equation was brought out in this paper. Flame height increases with the incre... [more]

Current climate change threats and increasing CO2 emissions, especially from the building stock, represent a context where action is required. It is necessary to provide efficient manners to manage energy demand in buildings and contribute to a decarbonised future. By combining new technologies, such as artificial intelligence, Internet of things, blockchain, and the exploitation of big data towards solving real life problems, the way could be paved towards smart and energy-aware buildings. In this context, the aim of this paper is to present a critical review and an in-detail definition of the big data value chain for the built environment in Europe, covering multiple needs and perspectives: “policy”, “technology” and “business”, in order to explore the main challenges and opportunities in this area.

Blue Economy represents a new and interesting concept on a global level, both from the economic potential but also by the fact that it can be used to reduce environmental degradation. The main goal of this research is to identify the causality relations between the greenhouse gas emissions, the Blue Economy and economic growth based on a panel of annual data from the 28 countries that are members of the European Union (EU) over the 2009−2018 period. After applying stationarity and cointegration tests, the long term cointegration coefficients shall be determined with the help of the fully modified ordinary least squares (FMOLS) estimator. Granger causality estimation based on the vector error correction model (VECM) was applied to identify the causality relationship between the variables and to detect the direction of causality. Based on the identified causality relations, the Blue Economy has a significant influence on greenhouse gas emissions in the long run. Unidirectional causality... [more]

The main purpose of the paper is to present a proposal to measure the relationships between Goal 7 of the 2030 Agenda for Sustainable Development and one of the areas considered in the green growth concept: environmental production efficiency. Both of these areas illustrate the relationship between the natural environment and the economy, emphasizing transformations in the field of energy use. Selected taxonomic methods, TOPSIS, and multicriteria taxonomy, were applied to study the relationships between the two areas. The results of the EU countries classification showed a variety of countries’ development pathways within a single economic community. Despite continued attempts to equalize the development levels between European Union countries in many strategic areas, they remain highly diversified. That is also true for the areas analyzed in the paper, which is a disturbing situation, indicating that both strategies might not correlate in all respects. Further research into the relati... [more]

In recent years, corporate involvement in CSR has become increasingly important and appreciated in the context of the ideas and assumptions regarding sustainable development. Due to the specificity of the energy sector, its particular impact on the environment, the living conditions of the population, and the social involvement of energy companies is particularly desirable, therefore it is observed and assessed by many stakeholder groups. The aim of this article is to assess the CSR commitment of Polish energy companies listed on the Warsaw Stock Exchange. The assessment was based on the proposed indicator model, based on the data published in the annual reports of the companies. The study uses data from the years 2016−2020. The main research question is as follows: What is the engagement in CSR activities of six Polish energy companies towards contractors, investors, employees, society, and the environment? The obtained results show that the investigated energy companies present a sim... [more]

More than 90% of Rwandans rely on polluting solid fuels to meet their cooking needs. The negative impacts on health, climate, and the environment have led the Rwandan government to set a target of halving that number to 42% by 2024. A National Master Plan to promote scale up of liquefied petroleum gas (LPG) has been developed to define (i) the necessary market conditions, (ii) public and private sector interventions, and (iii) the expected societal impacts. Findings are reported from modelling scenarios of scaling LPG use towards the 2024 policy target and the 2030 target for “universal access to clean modern energy” (SDG7). Household LPG use is projected to increase from 5.6% in 2020 to 13.2% by 2024 and 38.5% by 2030. This level of adoption could result in a reduction of 7656 premature deaths and 403,664 disability-adjusted-life-years (DALYs), as well as 243 million trees saved. Reductions in carbon dioxide and black carbon emissions equivalents (CO2e and BCe, respectively) are estim... [more]

The brick industry is currently facing a shortage of natural resources. Despite this, the demand for construction bricks is progressively increasing. Alternative materials, such as dredged sediments and solid organic waste, have been recently proposed as options to replace natural clay in brick manufacturing. Potential exploitation of dredged sediments in clay bricks is evaluated in this study. The chemical composition of the mixtures and the opto-thermal properties of brick samples, which differed for the dredged sediment content (from 10% to 50% of the clay weight), were investigated. Chemical analyses detected lower concentrations of heavy metals in bricks incorporating dredged sediments (DS). Negligible variations in thermal conductivity, thermal diffusivity, and specific heat were observed by increasing the amount of DS in the mixture. In particular, the thermal conductivity values ranged between 0.45 ± 0.03 W m−1 K−1 (DS-50) and 0.50 ± 0.03 W m−1 K−1 (DS-30). Conversely, the colo... [more]

The purpose of this research was to assess the development potential of cities and municipalities in Wałbrzych County, approached from the perspective of social, economic and environmental potential. Comparisons were performed for the periods 2002−2004 and 2016−2018. The following problem questions were formulated in the study: Which strategic goals can currently act as incentives for taking action in the analysed post-industrial areas, and for which ones should development be particularly strengthened? What development direction should be taken by individual municipalities in Wałbrzych County? The research covering the development potential of the municipalities was conducted using the multidimensional analysis method, and the similarities in municipal potential were analysed taking into account a comparison of distances between individual diagnostic variables. Among the analysed municipalities, in terms of social, economic and environmental potential, Szczawno-Zdrój and Czarny Bór ac... [more]

Fuel-related measures and modernization of small-scale combustion units has become the focus of attention in the renewable heat generation sector, as a means to promote local biomass utilization and fuel-flexibility while meeting strict environmental legislative requirements. With the aim to mitigate total particulate matter emissions and ash-associated problems characteristic of crop residue combustion, (1) corn cob pellets (with and without kaolin and binder) as well as (2) fuel blends with wood pellets were combusted in a pellet oven under full load. Results show that additivation or fuel blending (e.g., 50 wt. % wood and 50 wt. % corn cob pellets) reduce total particulate and CO-emissions by 48 to 60 wt. % and 64 to 89 wt. %, respectively, in comparison to baseline emissions from non-additivized corn cob pellets. Kaolin prevented sintering of corn cob ash. However, considerable grate ash entrainment was observed. TPM consists of a “primary network”—polyhedral and spherical particle... [more]

This paper investigates adaptive thermal comfort during summer in medical residences that are located in the French city of Troyes and managed by the Association of Parents of Disabled Children (APEI). Thermal comfort in these buildings is evaluated using subjective measurements and objective physical parameters. The thermal sensations of respondents were determined by questionnaires, while thermal comfort was estimated using the predicted mean vote (PMV) model. Indoor environmental parameters (relative humidity, mean radiant temperature, air temperature, and air velocity) were measured using a thermal environment sensor during the summer period in July and August 2018. A good correlation was found between operative temperature, mean radiant temperature, and PMV. The neutral temperature was determined by linear regression analysis of the operative temperature and Fanger’s PMV model. The obtained neutral temperature is 23.7 °C. Based on the datasets and questionnaires, the adaptive coef... [more]

This study estimates the environmental efficiency of 150 economies during the period of 2010−2017 to understand the environmental efficiency trend worldwide. This research adopts the meta-Malmquist approach to compare and capture the dynamic change in environmental efficiency among different income groups. The empirical results indicate that among the four income groups, only the low-income group suffers from regression in terms of environmental efficiency, while the high-income group achieves the greatest progress. For the high-income group, the source of improvement originates from the frontier shift rather than from efficiency change. By contrast, the improvement of the lower-income groups results from the catching-up effect. With regard to the effect of the Paris Agreement, only the lower middle-income group exhibits a statistical difference between the two periods, and environmental efficiency increases after the adoption of the Paris Agreement. The fight against global warming ca... [more]

The present article analyzes the technological advancement and innovations related to drilling operations. It covers the review of currently proven and emerging technologies that could mitigate the drilling operational deficiencies and instabilities that could hinder operational performance activities and the economic part of drilling development with great effort to minimize their environmental footprint. Drilling system design and operations are among the major aspects and cost-effective endeavors of the oil and gas industries, which are therefore technology dependent. They are also considered to be among the most expensive operations in the world, as they require huge expenses daily. Drilling success, depending on prevalent conditions, is a function of several general factors. These include the selection of the best technologies and tools, procedural optimization, concrete problem-solving, accurate prediction, and rapid decision-making. Consequently, any sorts of tools or advanced t... [more]

This study focuses on the valorization of the organic fraction of municipal solid waste (biopulp) by hydrothermal liquefaction. Thereby, homogeneous alkali catalysts (KOH, NaOH, K2CO3, and Na2CO3) and a residual aqueous phase recirculation methodology were mutually employed to enhance the bio-crude yield and energy efficiency of a sub-critical hydrothermal conversion (350 °C, 15−20 Mpa, 15 min). Interestingly, single recirculation of the concentrated aqueous phase positively increased the bio-crude yield in all cases, while the higher heating value (HHV) of the bio-crudes slightly dropped. Compared to the non-catalytic experiment, K2CO3 and Na2CO3 effectively increased the bio-crude yield by 14 and 7.3%, respectively. However, KOH and NaOH showed a negative variation in the bio-crude yield. The highest bio-crude yield (37.5 wt.%) and energy recovery (ER) (59.4%) were achieved when K2CO3 and concentrated aqueous phase recirculation were simultaneously applied to the process. The inorgan... [more]

The article aims to identify the latest trends in research on renewable energy, sustainability and the environment. A total of 92,873 publications from 123 Scopus sources for 2020−2021 are compared using the scoping review method. The results show that the most cited works in this sample are those by authors from the Asian region. The research of these authors focuses on the security, efficiency and reliability of separate elements in energy systems. Besides, the paper considers the problems regarding COVID disease along with the renewable energy sources, perovskite and organic solar panels, nanostructured materials and high energy density. Finally, the paper analyses applications of computer science methods in research on renewable energy, sustainability and the environment. The findings evidently show that recent advancements in computer science methods were not extensively used in the discussed research domain and give a great room for novel strategies of prognosing, simulation and... [more]

Increasing energy demand in buildings with a 40% global share and 30% greenhouse gas emissions has accounted for climate change and a consequent crisis encouraging improvement of building energy efficiency to achieve the combined benefit of energy, economy, and environment. For an efficient system, the optimization of different design control strategies such as building space load, occupancy, lighting, and HVAC becomes inevitable. Therefore, interdisciplinary teamwork of developers, designers, architects, and consumers to deliver a high-performance building becomes essential. This review aims to endorse the importance of Building Performance Simulation in the pre-design phase along with the challenges faced during its adaptation to implementation. A morphology chart is structured to showcase the improvement in Building Energy Efficiency by implementing Building Performance Simulation for different building energy systems and by implementing various energy efficiency strategies to achie... [more]

The article presents the course of the evolution of the concept of urban renewal’s emergence into its current, mature, integrated form of sustainable regeneration (sustainable urban regeneration—SUR). We present how the determination of renewal areas and its goals began to be based on particular indicators, and how the importance of these analyses gradually increased in managing the implementation of urban regeneration programs. Analytical techniques using GIS were used in the analyses of the differentiation of crisis phenomena inside cities before they became popular in smart city tools. Despite the wide use of GIS to analyze the diversity of crisis phenomena within the city, the availability of data means that different spheres are characterized with different accuracy. Starting from the significance of individual spheres, the focus has primarily been on the environment, which is underappreciated in Poland. Municipalities (urban, rural, urban−rural) with regeneration programs do not... [more]

This research presents the energy, exergy, economic, and environmental assessment, and multi-objective optimization of a flash-binary geothermal CCHP cycle. A sensitivity analysis of production well inlet temperature and cooling to power flow ratio on exergetic, economic, and environmental parameters was conducted. Furthermore, the effects of the inflation rate and plant working hours on economic parameters were investigated. Results showed that increasing the production well inlet temperature harms exergy efficiency and exergetic performance criteria and results in a gain in exergo-environmental impact index and heating capacity. In addition, the total plant cost increased by raising the production well temperature. Furthermore, increasing the cooling to power flow ratio caused a reduction in exergy efficiency, exergetic performance criteria, and produced net power and an enhancement in exergy destruction, cooling capacity, and total plant cost. The exergy efficiency and total cost ra... [more]

Seawater represents a potential resource to ensure sustainable availability of water for population and irrigation purposes, especially in some areas of the world. Desalination processes allow the production of fresh water, but they generate also brine as waste product. Sustainable brine management should be identified to ensure proper disposal and potentially resource recovery. This experimental study showed that emerging technologies such as Microbial Desalination Cells (MDCs) may provide a valuable contribution to the sustainability of the seawater desalination sector. In this paper, we report results on lab-scale desalination brine treatments applying MDCs, which allow energy savings, resource recovery, environmental impact minimization, and reduction of the organic load in municipal wastewater. Our results showed that MDCs’ treatment allows the removal of approximately 33 g of salts (62% of the total)—including chlorides, bromides, and sulphates—from 20 mL of brine within 96 h. Th... [more]

The purpose of this study is to identify the most relevant renewable energy technologies for buildings and to assess the effectiveness of their implementation in the long term for Kuwait. Methods of analogies and comparisons were used to determine the features of energy efficiency based on the technologies under study. The study proposes the methodological approach to assessing the effectiveness of the introduction of renewable energy technologies, determining the direction of increasing the energy efficiency of buildings and the investment efficiency of introducing these technologies. Renewable energy efficiency analysis for buildings in Kuwait confirms that solar energy systems have been the most widely available for widespread use of solar energy over the past three years. An increasing level of energy efficiency with a decrease in the notional cost of increasing energy savings is characteristic of solar collectors with booster reflectors. The proposed model for assessing the level... [more]

Efficient air-cooling systems for hot climatic conditions, such as Southern Europe, are required in the context of nearly Zero Energy Buildings, nZEB. Innovative air-cooling systems such as regenerative indirect evaporative coolers, RIEC and desiccant regenerative indirect evaporative coolers, DRIEC, can be considered an interesting alternative to direct expansion air-cooling systems, DX. The main aim of the present work was to evaluate the seasonal performance of three air-cooling systems in terms of air quality, thermal comfort and energy consumption in a standard classroom. Several annual energy simulations were carried out to evaluate these indexes for four different climate zones in the Mediterranean area. The simulations were carried out with empirically validated models. The results showed that DRIEC and DX improved by 29.8% and 14.6% over RIEC regarding thermal comfort, for the warmest climatic conditions, Lampedusa and Seville. However, DX showed an energy consumption three an... [more]

An increasing number of data sources and models to handle them call for transparency and openness in assessing their goodness and practical use for people [...]

This paper presents a techno-economic assessment of hydrokinetic energy of Cozumel Island, where ocean currents have been detected, but tourist activities are paramount. The main objective of this research is to identify devices that have been used to harvest hydrokinetic power elsewhere and perform an economic analysis as to their implementation in the Mexican Caribbean. First, the energy potential of the area was evaluated using simulated data available through the HYCOM consortium. Then, for four pre-commercial and commercial turbines, technical and economic analyses of their deployments were performed. Socio-environmental constraints were reviewed and discussed. Three optimal sites were identified, with an average annual hydrokinetic energy density of 3−6 MWh/m2-year. These sites meet the socio-environmental requirements for marine kinetic energy harvesting. Of the turbines considered in the analysis, the best energy price/cost ratio is that of SeaGen device, with a maximum theoret... [more]

This study aims to design a 16.4 MW photovoltaic solar system located in the Brazilian Northeast and quantify the associated greenhouse gas emissions and environmental payback. The energy system was designed to minimize the Levelized Cost of Energy. The greenhouse gas emissions were quantified with the Life Cycle Assessment methodology, expressing the environmental impact in terms of generated energy (kg CO2-eq/kWh) and following ISO 14040 and 14044. The environmental payback considered the Brazilian electricity mix and degradation of the panels. The results indicated a system capable of producing 521,443 MWh in 25 years, with an emission factor of 0.044 kg CO2-eq/kWh and environmental payback of five years and eight months. The emission factor is at least ten times lower than thermoelectric natural gas power plants. The solar panels were the main contributors to the greenhouse gas emissions, representing 90.59% of overall emissions. It is concluded that photovoltaic energy systems are... [more]

Solid fuel combustion in a chamber does not necessarily occur at a constant rate and may show fluctuations due to variables such as varying burning rates, chamber pressure, and residual combustion. These variables can cause the fuel to burn disproportionately. The acoustic environment of obstacle vortex-driven flow due to transient combustion with pressure oscillations in a solid fuel chamber is numerically investigated in the present study. Solid fuel combustion is considered transient, and flow characteristics of the present problem are governed by large eddies shed from an obstacle. Since unsteady Reynolds-averaged Navier-Stokes (URANS) simulations are not appropriate to compute the present flow phenomenon, therefore, a detached eddy simulation (DES) is performed to precisely predict the flow behavior. Simulation of steady-state combustion is carried out to validate the numerical results with available experimental data from the literature. The simulation of transient combustion sho... [more]