This wind tunnel study was conducted to investigate the similarity laws involved in the reasonable simulation of the wake characteristics of a full-scale wind turbine. A 5 MW scaled wind turbine model was designed using an optimization method based on the blade element momentum (BEM) theory. Subsequently, wind tunnel tests were carried out on the geometrically similar model and the thrust-optimized model, with different yaw angles and under various upstream flow conditions. The results indicated that the wake development of the wind turbine model was closely related to the thrust forces of the wind turbine, and both kinematic and dynamic similarity laws should be observed to achieve wake characteristics that are reasonably similar to those of a full-scale wind turbine. This study investigated the aerodynamic similarity principles of small-scale wind turbine models to develop a more effective method for simulating full-scale turbine wake characteristics in wind tunnel tests. The outcome... [more]

The estimated ultimate recovery (EUR) of shale gas is an important index for evaluating the production capacity of horizontal wells. The Weiyuan shale gas field has wells with considerable EUR differentiation, which hinders the prediction of the production capacity of new wells. Accordingly, 121 wells with highly differentiated production are used for analysis. First, the main control factors of well production are identified via single-factor and multi-factor analyses, with the EUR set as the production capacity index. Subsequently, the key factors are selected to perform the multiple linear regression of EUR, accompanied by the developed method for well production prediction. The thickness and drilled length of Long 111 (Substratum 1 of Long 1 submember, Lower Silurian Longmaxi Formation) are demonstrated to have the uttermost effects on the well production, while several other factors also play important roles, including the fractured horizontal wellbore length, gas saturation, brit... [more]

Heavy fuel oil has an energy density content comparable to distillate fuels but a very high viscosity that necessitates extra heating before spray combustion inside a boiler. Heavy fuel oil is also characterized by high asphaltenes, carbon residues, trace metals, such as vanadium and nickel, fuel-bound nitrogen, and sulfur. Asphaltenes are heavy polycyclic aromatic compounds with embedded heteroatoms and significantly affect the physico-chemical properties of heavy fuels; this makes them very difficult to burn and leads to the formation of large cenospheres (lightweight, inert, hollow spheres), due to an inefficient burning process. The primary goal of this study is to experimentally investigate the influence of the asphaltene concentration on the combustion of HFO under a swirling flame, finally reducing gaseous and solid pollution. We tested HFO samples containing asphaltene concentrations of 4, 6, 8, 16, and 24 wt.%, prepared by blending the light oil of diesel and pure asphaltenes... [more]

Increased renewable energy production and storage is a key pillar of net-zero emission. The expected growth in the exploitation of offshore renewable energy sources, e.g., wind, provides an opportunity for decarbonising offshore assets and mitigating anthropogenic climate change, which requires developing and using efficient and reliable energy storage solutions offshore. The present work reviews energy storage systems with a potential for offshore environments and discusses the opportunities for their deployment. The capabilities of the storage solutions are examined and mapped based on the available literature. Selected technologies with the largest potential for offshore deployment are thoroughly analysed. A landscape of technologies for both short- and long-term storage is presented as an opportunity to repurpose offshore assets that are difficult to decarbonise.

The essential requirement for a cleaner environment, along with rising consumption, puts a strain on the distribution system and power plants, reducing electricity availability, quality, and security. Grid-connected photovoltaic systems are one of the solutions for overcoming this. The examination and verification of transformerless topologies and control techniques was a significant goal of this study. The transformerless concept is advantageous for its high efficiency; the transformerless converter has added advantages of reduced price, complexity, weight, and size. This study presents a novel high-efficiency transformerless architecture that does not create common-mode currents and does not inject DC current into the grid. A single-phase transformerless inverter circuit with two step-down converters was constructed in this study. Low-frequency switches determine the polarity of the grid connection. In order to control the gate pulses of switching devices, which each regulate a half-... [more]

Renewable energy sources (RESs) are generally connected to the grid through power electronic interfaces, which generate electrical power instantaneously with little inertia. With the increasing penetration of RESs, the grid will gradually develop into a low inertia and underdamped power system, which results in serious grid frequency stabilization problems. The virtual synchronous generator (VSG) is an emerging technology that mimics the operation characteristics of traditional synchronous generators (SGs). Virtual inertia and damping are therefore introduced, which help to stabilize grid frequency. This paper gives a comprehensive overview of the VSG. The basic operation principle of VSG is introduced and analyzed in depth. The key issues related to VSG are summarized and discussed, including hardware configuration, software control strategies, energy supporting methods, and typical applications.

Experiments on the convection heat transfer and pressure drop of supercritical carbon dioxide in a mini vertical upward flow were investigated in a smooth tube with an inner diameter of 2 mm. The experiments were conducted with pressures ranging from 7.62 to 8.44 MPa, mass fluxes ranging from 600 to 1600 kg·m−2·s−1, and heat flux ranging from 49.3 to 152.3 kW·m−2. Results show that the peak of heat transfer occurs when the bulk fluid temperature is below the proposed critical temperature and the wall temperature is above the proposed critical temperature. For the 2 mm vertical upward flow, the radial buoyancy effects are relatively weak, and the axial thermal acceleration effect cannot be negligible. In this study, a new modified Jackson correlation for the supercritical carbon dioxide is proposed for convective heat transfer. To reflect the effect of flow acceleration on heat transfer, a dimensionless heat flux was introduced to construct a new semi-correlation of heat transfer. The n... [more]

Wind turbine wake redirection drawn by a yaw control has been proposed as a strategy to improve the performance of wind farms. However, the characteristics and the development of the curled wake structure deformed by the yaw action of the rotor are not well understood. In the present study, the structure of the wake behind a wind turbine imparted with various yaw angles subjected to uniform inflow was investigated using large-eddy simulation. The NREL 5MW reference wind turbine was modeled with an actuator disk with rotation to study the deformation process of the curled wake. The source of the vertical asymmetry in the wake deformation was found to be based on the interaction of global wake rotation and a counter-rotating vortex pair induced by the yaw angle. The yaw angle had a profound influence on the distortion of the wake and its trajectory, whose effect was naturally mitigated with downstream distance.

Numerous numerical and experimental studies have been conducted regarding the Concentrated Photovoltaic Thermal (CPVT) system because of its significant potential for efficient conversion of solar energy. The overall efficiency of the CPVT system is strongly dependent on the device, which extracts excess heat from photovoltaic cells. The most efficient cooling technology involves active cooling, which means that heat is collected from the PV cell via the forced flow of heat transfer fluid. This research paper provides an extensive discussion on devices dedicated to active-cooling CPVT systems, taking into account the latest solutions. First, a short introduction regarding CPVT systems and their main components is presented. The second part of this study presents state-of-the-art solutions in the field of heat extraction devices for the active cooling of photovoltaic cells. The available solutions are classified into two main groups depending on the scale of internal channels: macro- an... [more]

Due to their large and increasing size and the corrosive nature of salt water and high wind speeds, offshore wind turbines are required to be more robust, more rugged and more reliable than their onshore counterparts. The dynamic characteristics of the blade and its response to applied forces may be influenced dramatically by rotor rotational speed, which may even threaten the stability of the wind turbine. An accurate and computationally efficient structural dynamics model is essential for offshore wind turbines. A comprehensive model that takes the centrifugal stiffening effect into consideration could make rapid and accurate decisions with live data sensed from the structure. Moreover, this can enhance both the performance and reliability of wind turbines. When a rotating blade deflects in its plane of rotation or perpendicular to it, the centrifugal force exerts an inertia force that increases the natural frequencies and changes the mode shapes, leading to changes in the dynamic re... [more]

In the development of deep geological repositories (DGRs), performance assessment modeling is used to evaluate the integrity and performance of the engineered and geological barriers for thousands or millions of years of evolution of the disposal system. To evaluate the suitability of a site for a DGR, geoscientific data from dedicated site investigation programs are integrated into site-specific assessments. This paper presents the development and implementation of a modeling workflow aimed at comparing three potential siting areas for a DGR in Switzerland from the viewpoint of long-term safety and technical feasibility. The workflow follows the guidelines of the national regulator addressing safety relevant criteria such as the barrier efficiency of the host rock and its mechanical and chemical integrity in response to repository-induced influences and the long-term stability of the repository site over geological scales. In the regulatory requirements, the role of parametric, concep... [more]

In the pursuit of more efficient vehicles on the world’s roads, the vehicle thermal management system has become a limiting factor when it comes to EV range and battery life. In extreme climates, if the thermal system cannot pull down or warm up the EV powertrain in a timely manner, the battery is at serious risk of capacity loss or accelerated degradation. As waste heat is inherently limited with EVs, the way in which we provide the heat for warm-up must be as efficient as possible to reduce the load on the battery. In this paper, a revolutionary waste heat recovery (WHR) thermal management system designed by Tesla, nicknamed the ‘Octovalve’, is described, modelled, and simulated. This paper contributes to collective knowledge by presenting an in-depth breakdown of the key operating modes and outlining the potential benefits. Modelled in the multidomain Simulink Simscape software, the octovalve’s performance is directly compared to a typical EV WHR thermal management system. The syste... [more]

This paper presents proposals for using the direct-contact gravel, ground, air heat exchanger in single-family residential buildings with a passive house standard, according to the Passive House Institute (PHI). The methodology of their application consists of using heat and cold from the ground at an insignificant depth (about 1.5−4.0 m below the ground level for the central European climate) through an aggregate that is buried in the ground. This solution of simple installations is used for preheating and cooling fresh air drawn into the building through a mechanical ventilation system with heat recovery. In more complex applications it can be integrated with the source of heat and cold in passive buildings to create complete heating, cooling, and ventilation systems. In both cases, the air flowing through the exchanger is cooled and dried in summer, heated and humidified in winter, and filtered from pollen and bacteria all year. Direct contact of the deposit with the surrounding nat... [more]

Urban underground construction projects are intertwined vertically and horizontally, and adjacent confined spaces such as water supply and drainage pipelines, side ditches and underground canals may exist near buried gas pipelines. Once the buried gas pipeline leaks, the gas will diffuse into the confined space through the soil and even enter the residential room by the confined space, which brings serious potential safety hazards. In this paper, the underground adjacent confined space hazardous boundary (HB) of underground gas pipeline leakage was defined, the distribution properties of gas leakage diffusion flow field were analyzed by numerical simulation and the distribution law of gas entering the confined space was studied. Using the least-squares method and multiple regression theory, the gas concentration prediction model in the adjacent confined space of buried gas pipeline leakage was established, the HB calculation model was further deduced, and the HB drawing board was drawn... [more]

The wind turbine blade is an important component for harnessing wind energy. It plays a vital role in wind turbine operation. In this work, a study was conducted to investigate the dynamic behavior of an optimal rotary wind turbine blade with a bond graph approach simulated with MATLAB/Simulink. The model is considered as a twisted Rayleigh beam which is made of several sections of the type SG6043 airfoil. This type of airfoil is suitable for low wind conditions, and each section is subjected to aerodynamic loads that are computed using the blade element momentum theory. The bond graph model was developed based on the law of conservation of mass and energy in the systems, and then the model was converted to the MATLAB/Simulink toolbox; results were validated with SG6043 airfoil data and real wind data collected from selected specific sites of Abomsa, Metehara, and Ziway areas in Ethiopia.

The Luzhou area in the southern Sichuan Basin has experienced multiple tectonic movements, forming a complex fault system; the activity has an important impact on the enrichment of shale gas in this area. In order to reveal the influence of the fracture system on the differential enrichment of shale gas, this paper takes the southern Sichuan Basin as the research object. The structural evolution process and fracture development characteristics of the different tectonic units in Luzhou area of southern Sichuan were characterized by conducting a seismic profile analysis, structural recovery using a back-stripping method, and core hand specimen description. We clarified the control effect of the structural deformation and fracture on the differential enrichment of shale gas, and we established a differential enrichment model of shale gas in the Luzhou area. The results show that: (1) The Luzhou area has undergone the transformation of a multi-stage tectonic movement. There are many sets o... [more]

Recent developments in renewable energy installations in buildings have highlighted the potential improvement in energy efficiency provided by direct current (DC) distribution over traditional alternating current (AC) distribution. This is explained by the increase in DC load types and energy storage systems such as batteries, while renewable energy sources such as photovoltaics (PVs) produce electricity in DC form. In order to connect a DC distribution system to the alternating current grid (e.g., for backup, delivering energy storage to the grid) there is a need for a bidirectional inverter, which needs to operate over a wide range of source and load conditions and is therefore critical to the overall system performance. However, DC distribution in buildings is relatively new, with much of the research focused on the control of the DC bus connection between sources and loads, rather than on the grid connection. Therefore, this review aims to explore recent developments in bidirection... [more]

A water recuperation system (WRS) from an open-cathode proton exchange membrane fuel cell (PEMFC) is designed to increase the energy density of hydrogen production by hydrolysis of metal hydrides. WRS may significantly reduce the water weight in the carried fuel. The design is based on circulating the humid air through the PEMFC stack in a closed dome. To ensure oxygen supply to the PEMFC, the WRS has a ventilation inlet and an exhaust outlet. The required conditions for ventilation flow are developed theoretically and examined experimentally in a WRS prototype with a commercial PEMFC at 20−100 W. The experimental system includeds a closed dome, an edge cooling system for the PEMFC, a controllable ventilation air inlet, and an exhaust port. The humid exhaust air was cooled down to the ambient temperature to improve vapor condensation. Results show high efficiency (80% recuperated water from prediction), with a potential to achieve gravimetric hydrogen storage capacity (GHSC) of >6 wt%... [more]

The mass introduction of variable renewable energies, including wind and solar photovoltaic, leads to additional costs caused by the intermittency. Many recent studies have addressed these “integration costs,” and proposed novel metrics that replace the traditional metric known as the levelized cost of electricity (LCOE). However, the policy relevance of those metrics remains unclear. In this study, the author investigates and re-defines the concept of system LCOE, referring to prior studies, and proposes concrete methods to estimate them. Average system LCOE allocates the integration cost to each power source, dividing that by the adjusted power output. Marginal system LCOE revises the concept of system LCOE and value-adjusted LCOE proposed by prior studies, to be clearer and more policy-relevant. These metrics are also applied to Japan’s power sector in 2050, suggesting the necessity of aiming for a “well-balanced energy mix” in future power systems with decarbonised power sources.

The rapid transition from an efficiency-oriented to a renewable energy-based green environment raises questions about the sustainability of cogeneration models in the coming era of climate change. For securing the technological competitiveness of a cogeneration model in terms of sustainability, it is essential to come up with alternatives that can flexibly respond to changes in the market conditions. From the surveyed field operation data of the cogeneration model applied to an apartment complex, it was found that the actual operation performance may differ significantly from the theoretical expectation. Through diagnostic simulation analysis, the main cause of the disappointing performance in the case of the current cogeneration model after installation has been assessed, and the importance of a consistent operation strategy was demonstrated by the event-based correlation analysis based on field operation data. The impact of the rapid expansion and dissemination of the renewable energ... [more]

Aiming at the problems of pipeline blockage and equipment wear caused by large sand production in shallow gas hydrate mining on the seabed, based on the solid-state fluidization mining method, the idea of in situ separation of natural gas hydrate is proposed, and the downhole design is based on the physical parameters of hydrate mixed slurry. For the in situ helical separator, the CFD-Fluent commercial software was used to establish an analysis model and optimize the response surface of the model. The effects of the three-stage variable-pitch helix and blades on the performance of the separation device were investigated. The simulation results and response surface optimization were conducted through experiments to verify the accuracy. The results show that the third-stage pitch has the greatest impact on the separation efficiency and pressure drop, while the first-stage pitch has the least impact. The pressure drop and separation efficiency are fully considered. After the response surf... [more]

Increasing environmental pollution is driving an increase in the production and use of biofuels. The cost price of biodiesel could be reduced by using low-quality oilseeds unfit for human consumption and by applying the simultaneous oil extraction and transesterification process, avoiding the oil pressure stage. The purpose of this study was to investigate the enzymatic biofuel production process (in situ) by using rapeseed with high oil acidity for simultaneous oil extraction and transesterification with a mixture of butanol and mineral diesel fuel. The investigation of the in situ process was performed using a mixture of butanol and mineral diesel and the most effective biocatalyst Lipozyme TL IM was selected. The novelty of this paper consists of the fact that mineral diesel was used as the oil extractant, and the amount chosen was such that, at the end, a mixture of fuel with a ratio 9:1 of mineral diesel to biodiesel was be produced. The experiments were carried out using ground r... [more]

The use of biofuels to power compression−ignition engines makes it possible to reduce emissions of certain harmful components of exhaust gases. The purpose of this study was to determine the influence of second-generation biofuels on the course of indicator graphs and heat release characteristics of the Perkins 1104D-44TA compression−ignition engine. For comparative purposes, the same tests were carried out by feeding the engine with first-generation biofuel and diesel fuel. Babassu butyl esters (BBuE) were used as the second-generation biofuel. The second fuel was a first-generation biofuel—rapeseed oil methyl esters (RME). Analysis of the results made it possible to draw conclusions about the effect of using 2nd and 1st generation biofuels on the parameters of the combustion process. When the DF engine was powered, the lowest fuel dose per work cycle was obtained. In the case of RME and BBuE fuels, it depends on the engine load. For low loads, higher consumption is for RME, and for h... [more]

The theoretical feasibility of the power output strategy based on rotor cone angle control for ultra-scale downwind wind turbines is studied in this paper via the Open FAST simulation platform. The performance of five cases, namely UW, DW, DWC, DW6, and DW6IC, which have different rotor parameters or control strategies compared with the reference DTU 10 MW wind turbine, are calculated and analyzed. It is found that the downwind rotors have significant advantages in reducing the blade root load. The DW case reduces the peak load at the blade root by 22.54% at the cost of 1.57% annual energy production loss. By extending the length and redesigning the stiffness of the blade, the DW6 case achieves 14.82% reduction in the peak load at the blade root and 1.67% increase in the annual energy production under the same blade weight as that of the UW. The DWC case with rotor cone angle control has the same aerodynamic performance as the DW case with the same blade parameters. However, when the w... [more]

Agro-industrial residues such as bagasse, pomace, municipal residues, vinasse and cheese whey are an environmental problem around the world, mainly due to the huge volumes that are generated because of the food production to satisfy the nutritional needs of the growing world population. Among the above residues, cheese whey has gained special attention because of its high production with a worldwide production of 160 million tons per year. Most of it is discarded in water bodies and land causing damage to the environment due to the high biological oxygen demand caused by its organic matter load. The environmental regulations in developing countries have motivated the development of new processes to treat transform cheese whey into added-value products such as food supplements, cattle feed and food additives. In addition, during the last decade, several processes and technologies have been developed to produce bioenergy through the biotechnological process using cheese whey as a potenti... [more]