Particle deposition tests were conducted in a turbine deposition facility with an internally staged single-tube combustor to investigate the individual effect of the gas temperature and angle of attack. Sand particles were seeded to the combustor and deposited on a turbine blade with film-cooling holes at temperatures representative of modern engines. Fuel-air ratios were varied from 0.022 to 0.037 to achieve a gas temperature between 1272 and 1668 K. Results show that capture efficiency increased with increasing gas temperature. A dramatic increase in capture efficiency was noted when gas temperature exceeded the threshold. The deposition formed mostly downstream of the film-cooling holes on the pressure surface, while it concentrated on the suction surface at the trailing edge. Deposition tests at angles of attack between 10° and 40° presented changes in both deposition mass and distribution. The capture efficiency increased with the increase in the angle of attack, and simultaneousl... [more]

Among the available solutions for building heating and cooling, district heating (DH) and district cooling (DC) systems are considered some of the best options since they can ensure a better control of pollutant emissions and greater efficiency than individual systems. Nevertheless, improvements are needed to increase their sustainability and reliability. The so-called “low temperature district heating” (LTDH) concept has been introduced in recent years in an attempt (i) to reduce the distribution heat losses through a temperature decrease in the DH network, (ii) to favor the integration with renewable energy sources, and (iii) to create the conditions required for the development of future smart energy systems. However, many concerns have been raised about its implementation in both existing and new systems. For this reason, this paper aims to identify the stakeholders’ ranking of the barriers against LTDH system development and implementation over the next few years. Aiming to this,... [more]

The deformation and failure of coal and rock materials is the primary cause of many engineering disasters. How to accurately and effectively monitor and forecast the damage evolution process of coal and rock mass, and form a set of prediction methods and prediction indicators is an urgent engineering problems to be solved in the field of rock mechanics and engineering. As a form of energy dissipation in the deformation process of coal and rock, microseismic (MS) can indirectly reflect the damage of coal and rock. In order to analyze the relationship between the damage degree of coal and rock and time-frequency characteristics of MS, the deformation and fracture process of coal and rock materials under different loading modes was tested. The time-frequency characteristics and generation mechanism of MS were analyzed under different loading stages. Meanwhile, the influences of properties of coal and rock materials on MS signals were studied. Results show that there is an evident mode cut... [more]

Backward injection film cooling holes were studied to improve film cooling effectiveness using simple cylindrical holes, and this principle was applied to an actual gas turbine. Although film cooling effectiveness was improved using a backward injection film cooling hole, the backward flow of combustion gas from the backward injection cooling hole was one of the major reasons for cracks in the hot components. To prevent cracks and backward flow in the backward injection film cooling hole, this study changed the inlet compound angle of the backward injection film cooling hole. Numerical analysis using CFX v. 17.0 was performed to calculate the flow characteristics and film cooling effectiveness of backward injection film cooling. Aa a result, the effect of the inlet compound angle of the backward injection film cooling hole was confirmed to prevent the backward flow, which increased upon increasing the inlet compound angle. This study shows that the backward flow and cracks in the backw... [more]

Given the prejudicial environmental effects of fossil-fuel based energy production, renewable energy sources can contribute significantly to the sustainability of human society. As a clean, cost effective and inexhaustible renewable energy source, wind energy harvesting has found a wide application to replace conventional energy productions. However, concerns have been raised over the noise generated by turbine operating, which is helpful in fault diagnose but primarily identified for its adverse effects on the local ecosystems. Therefore, noise monitoring and separation is essential in wind turbine deployment. Recent developments in condition monitoring provide a solution for turbine noise and vibration analysis. However, the major component, aerodynamic noise is often distorted in modulation, which consequently affects the condition monitoring. This study is conducted to explore a novel approach to extract low-frequency elements from the aerodynamic noise background, and to improve t... [more]

Improving energy recycle is an important way to save energy resources and preserve the global environment. Chemical heat pump (CHP) is a technology for saving energy, which utilizes chemical reactions to store thermal energy such as waste heat and solar heat, then release it to provide heat for heating/cooling/refrigeration. For a practical CHP, it is necessary to find cheaper and more stable supply materials. In order to evaluate the possibility of calcium oxide from natural Ofunato natural limestone including impurities, we compare Ofunato limestone with Kawara natural limestone and Garou natural limestone from Japan. These calcium oxides worked as a reactant for CaO/H2O/Ca(OH)2 CHP by repeated hydration/dehydration reaction cycle experiments in a thermogravimetric analyzer. As a result, Ofunato CaO exhibits a high hydration reaction rate after decarbonization at 1223 K for 5 h. The reactivity increased by the repeated hydration reaction although the first hydration rate was low. Fur... [more]

Since the 1990s, CO2 emissions have increased steadily in line with the growth of production and the use of energy in the manufacturing sector in Thailand. The Logarithmic Mean Divisia Index Method is used for analysing the sources of changes in CO2 emissions as well as the CO2 emission intensity of the sector in 2000−2018. On average throughout the period, both the amount of CO2 emissions and the CO2 emission intensity increased each year relative to the baseline. The structural change effect (effect of changes of manufacturing production composition) reduced, but the intensity effect (effect of changes of CO2 emissions of individual industries) increased the amount of CO2 emissions and the CO2 emission intensity. The unfavourable CO2 emission intensity change came from the increased energy intensity of individual industries. The increased use of coal and electricity raised the CO2 emissions, whereas the insignificant change in emission factors showed little impact. Therefore, the stu... [more]

Biodiesel is a clean and renewable fuel, which is considered as the best alternative to diesel fuel, but the feedstock contributes more than 70% of the cost. The most important constituent essential for biodiesel development is to explore cheap feedstock with high oil content. In this work, we found novel non-edible plant seeds of Koelreuteria paniculata (KP) with high oil contents of 28−30 wt.% and low free fatty acid contents (0.91%), which can serve as a promising feedstock for biodiesel production. KP seed oil can convert into biodiesel/fatty acid methyl esters (FAMEs) by base-catalyzed transesterification with the highest biodiesel production of 95.2% after an optimization process. We obtained the optimal transesterification conditions, i.e., oil/methanol ratio (6:1), catalyst concentration (0.32), reaction temperature (65 °C), stirring rate (700 rpm), and reaction time (80 min). The physico-chemical properties and composition of the FAME were investigated and compared with minera... [more]

Waste heat recovery is an actual goal. The best way to valorize waste heat is to use it directly with the appropriate level of temperature. If the temperature level is insufficient, many reverse machine configurations are available in order to obtain the appropriate conditions (the most known are heat pumps and heat transformers). Finally, the remaining unused heat could be converted to any noble form of energy (mechanical, electrical essentially). We propose here to examine, with a new point of view, the thermomechanical conversion limit of waste heat. This limit corresponds to adiabatic conversion for an endo-reversible Carnot engine, with a perfect thermal contact at the atmospheric sink (supposed infinite). The Carnot−Chambadal model version is applied to latent and sensible heat recovery cases. The results associated with these two cases differ fundamentally. Comments are provided on the two studied cases, and new criteria to characterize the corresponding waste heat recovery are... [more]

The lack of long-term financing, the low rate of return, the existence of various risks, and the lack of capacity of market players are major challenges for the development of green energy projects. This paper aimed to highlight the challenges of green financing and investment in renewable energy projects and to provide practical solutions for filling the green financing gap. Practical solutions include increasing the role of public financial institutions and non-banking financial institutions (pension funds and insurance companies) in long-term green investments, utilizing the spillover tax to increase the rate of return of green projects, developing green credit guarantee schemes to reduce the credit risk, establishing community-based trust funds, and addressing green investment risks via financial and policy de-risking. The paper also provides a practical example of the implementation of the proposed tools.

The issue of real-time deep down-regulation ancillary service has received increasing attention in the Northeast of China. Participation of combined heat and power plants with multitype units and flexible heating devices in the market is investigated. This paper establishes a model of feasible operating region and the coal consumption function for the combined heat and power plant. An internal optimal dispatch model and the minimum overall electric power output model for the plant satisfying a given heat load are presented. Furthermore, the models of total cost for down-regulation and average cost for deep down-regulation in two levels are established. These models are validated based on the realistic data of the plant in the Northeast of China. In case studies, the influence factors and change rules of the minimum electric power output, the total cost, and the average cost of plants are analyzed.

Photovoltaic energy presents environmental advantages; however, these advantages are limited by the cost of manufacturing solar cells and in many cases, scarce or dangerous materials are incorporated. Therefore, the use of natural dyes from mortiño (Vaccinium floribundum) as sensitizers in solar cells is proposed. The dyes were extracted by maceration in acidified methanol (HCl, citric acid and trifluoroacetic acid TFA) and were characterized by High-Performance Liquid Chromatography (HPLC), Thin-Layer Chromatography (TLC) and spectrometric methods (UV-Vis, IR and MS-MALDI). The construction and characterization of cells were in standard conditions. The study confirms that pigments in mortiño are flavonoids of the anthocyanidin group as: cyanidin-3-galactoside, and cyanidin-3-arabinoside. The efficiency of solar cells was between 0.18−0.26%; the extraction with TFA in methanol leads to the best performance. Although they have low power conversion efficiency, mortiño dyes could be an al... [more]

Close-packed contra-rotating vertical-axis turbines have potential advantages in wind and hydrokinetic power generation. This paper describes the development of a numerical model of a vertical axis turbine with a torque-controlled system using an actuator line model (ALM). The developed model, coupled with the open-source OpenFOAM computational fluid dynamics (CFD) code, is used to examine the characteristics of turbulent flow behind a single two-bladed vertical-axis turbine (VAT). The flow field containing the turbine is simulated by solving the unsteady Reynolds-averaged Navier-Stokes (URANS) equations with a k - ω shear stress transport (SST) turbulence model. The numerical model is validated against experimental measurements from a two-bladed H-type wind turbine. Turbine loading is predicted, and the vorticity distribution is investigated in the vicinity of the turbine. Satisfactory overall agreement is obtained between numerical predictions and measured data on thrust co... [more]

Traditional acoustic evaluation of a diesel engine generally uses the A-weighted sound pressure level (AWSPL) and radiated sound power to assess the noise of an engine prototype present in an experiment. However, this cannot accurately and comprehensively reflect the auditory senses of human subjects during the simulation stage. To overcome such shortage, the Moore−Glasberg loudness and sharpness approach is applied to evaluate and improve the sound quality (SQ) of a 16 V-type marine diesel engine, and synthesizing noise audio files. Through finite element (FE) simulations, the modes of the engine’s block and the average vibrational velocity of the entire engine surface were calculated and compared with the test results. By further applying an automatically matched layer (AML) approach, the engine-radiated sound pressure level (SPL) and sound power contributions of all engine parts were obtained. By analyzing the Moore−Glasberg loudness and sharpness characteristics of three critical s... [more]

This study presents the further development of the TU Wien dual fuel mechanism, which was optimized for simulating ignition and combustion in a rapid compression expansion machine (RCEM) in dual fuel mode using diesel and natural gas at pressures higher than 60 bar at the start of injection. The mechanism is based on the Complete San Diego mechanism with n-heptane extension and was attuned to the RCEM measurements to achieve high agreement between experiments and simulation. This resulted in a specific application area. To obtain a mechanism for a wider parameter range, the Arrhenius parameter changes performed were analyzed and updated. Furthermore, the San Diego nitrogen sub-mechanism was added to consider NOx formation. The ignition delay time-reducing effect of propane addition to methane was closely examined and improved. To investigate the propagation of the flame front, the laminar flame speed of methane−air mixtures was simulated and compared with measured values from literatur... [more]

A simple yet accurate photovoltaic (PV) performance curve as a function of satellite-based solar irradiation is necessary to develop a PV power forecasting model that can cover all of South Korea, where more than 35,000 PV power plants are currently in operation. In order to express the nonlinear power output of the PV module with respect to the hourly global horizontal irradiance derived from satellite images, this study employed the Gompertz model, which is composed of three parameters and the sigmoid equation. The nonphysical behavior of the Gompertz model within the low solar irradiation range was corrected by combining a linear equation with the same gradient at the conjoint point. The overall fitness of Linear-Gompertz regression to the 242 PV power plants representing the country was R2 = 0.85 and nRMSE = 0.09. The Gompertz model coefficients showed normal distributions and equivariance of standard deviations of less than 15% by year and by season. Therefore, it can be conjectur... [more]

Rapid developments in energy storage and conversion technologies have led to the proliferation of low- and medium-power electric vehicles. Their regular operation typically requires an on-board battery charger that features small dimensions, high efficiency and power quality. This paper analyses an interleaved step-down single-ended primary-inductor converter (SEPIC) operating in the discontinuous conduction mode (DCM) for charging of battery-powered light electric vehicles such as an electric wheelchair. The required characteristics are achieved thanks to favourable arrangement of the inductors in the circuit: the input inductor is used for power factor correction (PFC) without additional elements, while the other inductor is used to provide galvanic isolation and required voltage conversion ratio. A modular interleaved structure of the converter helps to implement low-profile converter design with standard components, distribute the power losses and improve the performance. An optima... [more]

A horizontal well with hydraulic fractures is key to forming a fracture network in oil shale for the generated hydrocarbon flows. By considering the influence of anisotropic strength, a prediction model is proposed for fracture initiation by studying different fracture initiation modes (FIMs) in oil shale: failure of the intact rock matrix and of the bedding planes. Through a case study on Nong’an oil shale, the influences of wellbore trajectory and bedding planes on the fracture initiation pressure (FIP), location (FIL), and FIM were analyzed and the induced changes in wellbore trajectory design were concluded. The preferred angle between the wellbore axis and the minimum horizontal principal stress was the same of 90° or 270°, when the lowest required FIP corresponded to the failure of the intact rock matrix. However, when the angle corresponded to the failure of the bedding planes, the preferred direction of the wellbore axis was away from the fixed direction and not corresponding t... [more]

Catalytic hydrotreatment is recognized as an efficient method to improve the properties of pyrolysis liquids (PO) to allow co-feeding with fossil fuels in conventional refinery units. The promising catalyst recipes identified so far are catalysts with high nickel contents (38 to 57 wt.%), promoted by Cu, Pd, Mo and/or a combination, and supported by SiO2, SiO2-ZrO2, SiO2-ZrO2-La2O3 or SiO2-Al2O3. To gain insights into the reactivity of the pyrolytic sugar (PS) and pyrolytic lignin (PL) fraction of PO, hydrotreatment studies (350 °C, 120 bar H2 pressure (RT) for 4 h) were performed in a batch autoclave. Catalyst performance was evaluated by considering the product properties (H/C ratio, the charring tendency (TGA) and molecular weight distribution (GPC)) and the results were compared with a benchmark Ru/C catalyst. All Ni based catalysts gave products oils with a higher H/C compared to Ru/C. The Mo promoted catalyst performed best, giving a product with the highest H/C ratio (1.54) and... [more]

Strong tectonic movement brings great risk to exploration of shale gas in southern China, especially in Lower Cambrian shale with complex tectonic backgrounds, which has good hydrocarbon-generation matter but low or no gas content. In this paper, the Lower Cambrian shale from the southeast Chongqing region, located in the Upper Yangtze Platform, and the Xiuwu Basin, located in the Lower Yangtze Platform, were selected as the research objects. First, the gas components in shale gas samples were measured, then analysis of nitrogen isotopic was used to reveal the nitrogen sources. Using regional geological backgrounds, core description, and seismic interpretation, combined with the perpendicular and parallel permeability test and focused ion beam−helium ion microscopy (FIB−HIM) observation, the reasons for high content of nitrogen in the Lower Cambrian shale from the Xiuwu Basin and the Southeast Chongqing region were clarified. The results indicate that the main sources of nitrogen in th... [more]

The quick U-building (QUB) method is used to measure the overall heat loss coefficient of buildings during one to two nights by applying heating power and by measuring the indoor and the outdoor temperatures. In this paper, the numerical model of a real house, previously validated on experimental data, is used to conduct several numerical QUB experiments. The results show that, to some extent, the accuracy of QUB method depends on the boundary conditions (solar radiation), initial conditions (initial power and temperature distribution in the walls) and on the design of QUB experiment (heating power and duration). QUB method shows robustness to variation in the value of the overall heat loss coefficient for which the experiment was designed and in the variation of optimum power for the QUB experiments. The variations in the QUB method results are smaller on cloudy than on sunny days, the error being reduced from about 10% to about 7%. A correction is proposed for the solar radiation abs... [more]

The paper investigates the dynamics of the thermal field of the ACCC (aluminum conductor composite core) line. The system was heated by solar radiation and current flow. Conductor cooling was modeled using the total heat transfer coefficient as the sum of convective and radiative components. The temperature increase generated by the current is described by a system of parabolic differential equations with an appropriate set of boundary, initial and continuity condition. The mentioned boundary-initial problem was solved by a modified Green’s method, adapted to the layered structure of the system. For this purpose, Green’s functions, as the kernels of integral operators inverse to differential ones, were determined. Aluminum resistivity and heat transfer coefficient change significantly with temperature. For this reason, the solution to the problem is presented in the form of a lower and upper estimation of the heating curve and local time constant. A steady-state current rating was also... [more]

In this study, the vertically-oriented pulsating heat pipe (PHP) heat exchangers charged with either water or HFE-7000 in a filling ratio of 35% or 50% were fabricated to exchange the thermal energy between two air streams in a parallel-flow arrangement. Both the effectiveness of the heat exchangers and the thermal resistance of PHP with a size of 132 × 44 × 200 mm, at a specific evaporator temperature ranging from 55 to 100 °C and a specific airflow velocity ranging from 0.5 to 2.0 m/s were estimated. The results show that the heat pipe charged with HFE-7000 in either filling ratio is likely to function as an interconnected array of thermosiphon under all tested conditions because of the unfavorable tube inner diameter, whereas the water-charged PHP possibly creates the pulsating movement of the liquid and vapor slugs once the evaporator temperature is high enough, especially in a filling ratio of 50%. The degradation in the thermal performance of the HFE-7000-charged PHP heat exchang... [more]

This manuscript presents an advanced exergo-economic analysis of a waste heat recovery system based on the organic Rankine cycle from the exhaust gases of an internal combustion engine. Different operating conditions were established in order to find the exergy destroyed values in the components and the desegregation of them, as well as the rate of fuel exergy, product exergy, and loss exergy. The component with the highest exergy destroyed values was heat exchanger 1, which is a shell and tube equipment with the highest mean temperature difference in the thermal cycle. However, the values of the fuel cost rate (47.85 USD/GJ) and the product cost rate (197.65 USD/GJ) revealed the organic fluid pump (pump 2) as the device with the main thermo-economic opportunity of improvement, with an exergo-economic factor greater than 91%. In addition, the component with the highest investment costs was the heat exchanger 1 with a value of 2.769 USD/h, which means advanced exergo-economic analysis i... [more]

In this study, the cold-start failure processes of a polymer electrolyte fuel cell have been investigated numerically for different initial membrane water content λ 0 and the startup current densities I 0 . The result shows that the failure of the cell cold-start process is mostly attributed to the anode dehydration when the cell operates with relatively large current density. However, the failure is dominated by the cathode pore blockage when the cell starts with relatively high initial membrane water content. Corresponding maps for the classification of startup failure modes are plotted on the λ 0 − I 0 plane with different startup temperatures. Three zones, including the anode dehydration, the cathode pore blockage, and the ambiguous region, can be observed. They can be distinguished with different startup failure mechanisms. The anode dehydration zone is expanded as the cell startup temperature drops due to the weakening of the membrane water back-dif... [more]