This paper performs an in-depth investigation and analysis on a catastrophic hazardous chemical accident involving domino effects in China based on an emerging accident causation model—the 24Model. The triggers and roots of the incident from the individual and organizational levels have been identified and several useful lessons have been summarized to avoid similar mistakes. This accident began with a leak of vinyl chloride caused by the failure of the gas holder’s bell housing and the operators’ mishandling. Leaked vinyl chloride was ignited by a high-temperature device in the process of diffusion and the fire quickly spread to the illegally parked vehicles. Several organizations were involved in this accident, and the chemical company should bear the main responsibility for it, and shall establish and implement an effective safety management system in its organizational structure and staffing, facilities management, hazards identification, emergency disposal, etc., to improve safety... [more]

The goal of this work is to design a supply chain network that distributes algae biomass from supply locations to meet biodiesel demand at specified demand locations, given a specified algae species, cultivation (i.e., supply) locations, demand locations, and demand requirements. The final supply chain topology includes the optimum sites to grow biomass, to extract algal oil from the biomass, and to convert the algae oil into biodiesel. The objective is to minimize the overall cost of the supply chain, which includes production, operation, and transportation costs over a planning horizon of ten years. Algae production was modeled both within the U.S. State of Oklahoma, as well as the entire contiguous United States. The biodiesel production cost was estimated at $7.07 per U.S. gallon ($1.87 per liter) for the State of Oklahoma case. For the contiguous United States case, a lower bound on costs of $13.68 per U.S. gallon ($3.62 per liter) and an upper bound of $61.69 ($16.32 per liter) w... [more]

The aim of this study was to find the best design that is suitable for optimizing the recovery of the representatives of the 2nd, 3rd and 4th generation of fluoroquinolones. The following designs were applied: Central Composite Design, Box−Behnken Design and Doehlert Design. The recovery, which was a dependent variable, was estimated for liquid−liquid extraction. The time of shaking, pH, and the volume of the extracting agent (dichloromethane) were the independent variables. All results underwent the statistical analysis (ANOVA), which indicated Central Composite Design as the best model for evaluation of the recovery. For each analyte, an equation was generated that enabled to estimate the theoretical value for the applied conditions. The graphs for these equations were provided by the Response Surface Methodology. The statistical analysis also estimated the most significant factors that have an impact on the liquid−liquid extraction, which occurred to be pH for ciprofloxacin and moxi... [more]

Conventional leak detection techniques require improvements to detect small leakage (<10%) in gas mixture pipelines under transient conditions. The current study is aimed to detect leakage in gas mixture pipelines under pseudo-random boundary conditions with a zero percent false alarm rate (FAR). Pressure and mass flow rate signals at the pipeline inlet were used to estimate mass flow rate at the outlet under leak free conditions using Hammerstein model. These signals were further used to define adaptive thresholds to separate leakage from normal conditions. Unlike past studies, this work successfully detected leakage under transient conditions in an 80-km pipeline. The leakage detection performance of the proposed methodology was evaluated for several leak locations, varying leak sizes and, various signal to noise ratios (SNR). Leakage of 0.15 kg/s—3% of the nominal flow—was successfully detected under transient boundary conditions with a F-score of 99.7%. Hence, it can be conclude... [more]

In order to systematically elucidate the combustion performance of fuel during sintering, this paper explores the influence of three factors, namely coal substitution for coke, quasi-particle structure and the coupling effect with reduction and oxidation of iron oxide, on fuel combustion characteristics, and carries out the kinetic calculation of monomer blended fuel (MBF) and quasi-granular fuel (QPF). The results show that replacing coke powder with anthracite can accelerate the whole combustion process. MBF and QPF are more consistent with the combustion law of the double-parallel random pore model. Although the quasi-particle structure increases the apparent activation energy of fuel combustion, it can also produce a heat storage effect on fuel particles, improve their combustion performance, and reduce the adverse effect of diffusion on the reaction process. In the early stage of reaction, the coupling between combustion of volatiles and reduction of iron oxide is obvious. The oxi... [more]

This work reports the synthesis of natural zeolite-based silver and magnetite nanocomposites and their application for the catalytic oxidation of methylene blue in water. The zeolite was impregnated with 5.5 wt.% Fe in the form of magnetite nanoparticles with size of 32 nm, and with 6.4 wt.% Ag in the form of silver oxide and metallic silver nanoparticles with sizes of 42 and 20 nm, respectively. The results showed that physical adsorption contributed to the removal of methylene blue by 25−36% and that Fe3O4@NZU is superior to Ag2O@NZU and Ag0@NZU, leading to 55% removal without oxidant and 97% in the presence of H2O2. However, there is no evidence of significant mineralization of methylene blue. The application of reaction rate models showed that the reaction order changes from zero to first and second order depending on the H2O2 concentration.

The chemical industry is essential in the social economy, and the issue of production safety has aroused widespread concern. Chemical safety incidents occupy the headlines from time to time, and chemical production safety management is particularly important. This paper presents an application model based on evolutionary game theory in the assessment and analysis of chemical production safety management. The model uses evolutionary game theory to construct a strategic interactive payoff matrix between the management department of a chemical plant and the chemical plant using a replicated dynamic equation to analyze their strategic interaction and to reveal the evolution of behavioral strategy selection. The evolution results were verified and simulated. The application of this model provides an effective safety management basis and recommendations for the management of chemical plants, providing a foundation for the safe production and healthy development of chemical plants.

Over a long period of time, humans have explored many natural resources looking for remedies of various ailments. Traditional medicines have played an intrinsic role in human life for thousands of years, with people depending on medicinal plants and their products as dietary supplements as well as using them therapeutically for treatment of chronic disorders, such as cancer, malaria, diabetes, arthritis, inflammation, and liver and cardiac disorders. However, plant resources are not sufficient for treatment of recently emerging diseases. In addition, the seasonal availability and other political factors put constrains on some rare plant species. The actual breakthrough in drug discovery came concurrently with the discovery of penicillin from Penicillium notatum in 1929. This discovery dramatically changed the research of natural products and positioned microbial natural products as one of the most important clues in drug discovery due to availability, variability, great biodiversity, u... [more]

Protein glycation and oxidative stress lead to severe health complications in various diseases including diabetes mellitus. The intake of flavonoid-rich foods has been confirmed previously to have a positive effect on human health. Ginger is an important source of flavonoids and is one of the most widely used traditional medicines in many Asian countries. The aim of this study was to verify the therapeutic potential of methanolic extract from ginger against glycation and other oxidative stress-induced complications using in vitro study. In this study, quantitative estimations of antioxidant components such as total phenolic and flavonoids were determined by UV−visible spectrophotometry. The anti-inflammatory action of the ginger extract was checked by determining its protective action against the denaturation of proteins, anti-proteinase activity and its membrane stabilization effect. The anti-inflammatory action of ginger extract was found to be comparable with reference standard drug... [more]

Heating flame furnaces are the main type of furnaces used for heating and heat treatment of metal products in metallurgy and mechanical engineering. In the working chamber of a modern heating furnace, there should be neither high-temperature nor stagnation zones. One of the methods used to provide such combustion conditions is the application of distributed (volumetric) combustion. Owing to this method, heating quality is ensured by creating a uniform temperature field and equivalent heat exchange conditions, regardless of the placement of the charge in the working chamber of the furnace. In this work, we numerically study the volumetric combustion and influences of small- and large-scale recirculation ratios of furnace gases, the influence of temperature fluctuation on the regenerator nozzle, and the working parameters at the starting phase and reverse.

Microorganisms colonizing plastic waste material collected in composting-, landfill-, and anaerobic digestion plants were isolated to obtain novel strains maximally adapted to the degradation of plastics due to long-term contact with plastic polymers. Twenty-six bacterial strains were isolated and identified by the 16 S rRNA method, and eighteen strains of yeasts and fungi using 18 S rRNA and the internal transcribed spacer ITS sequencing of the 18 S rRNA gene. In selected strains, the ability to degrade linear low-density polyethylene (LLDPE), low-density polyethylene (LDPE), polystyrene (PS), and polyvinyl chloride (PVC) was tested in aerobic liquid-medium cultures. An oxidative, two-step pretreatment of LLDPE and LDPE using γ- or UV-irradiation followed by a high-temperature treatment was carried out, and the pretreated plastics were also included in the degradation experiments. The respective weight losses after biodegradation by Trichoderma hamatum were: virgin and γ/T90-pretreate... [more]

The porous Ti/Sb-SnO2/Ni-Ce-PbO2 electrode was prepared by using a porous Ti plate as a substrate, an Sb-doped SnO2 as an intermediate, and a PbO2 doped with Ni and Ce as an active layer. The surface morphology and crystal structure of the electrode were characterized by scanning electron microscope(SEM), energy dispersive spectrometer(EDS), and X-Ray diffraction(XRD). The electrochemical performance of the electrodes was tested by linear sweep voltammetry (LSV), cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and electrode life test. The results show that the novel porous Ni-Ce-PbO2 electrodes with larger active surface area have better electrochemical activity and longer electrode life than porous undoped PbO2 electrodes and flat Ni-Ce-PbO2 electrodes. In this work, the removal of Cl− in simulated wastewater on three electrodes was also studied. The results show that the removal effect of the porous Ni-Ce-PbO2 electrode is obviously better than the other two el... [more]

Biomass is currently one of the world’s major renewable energy sources. Biomass in a powder form has been recently proposed as the most encouraging of biomass contours, especially because it burns like a gas. In the current study, biomass powder was examined, for the first time, as a direct solid fuel in internal combustion engines. The aim of the current study was to investigate modeling tools for simulation of biomass powder in combustion engines (CE). The biomass powder applied was in a micro-scale size with a typical irregular shape; the powder length was in the range of 75−5800 μm, and the diameter was in the range 30−1380 μm. Different mechanisms for biomass powder drying and devolatilization/gasification were proposed, including different schemes’ and mechanisms’ rate constants. A comparison between the proposed models and experiments was carried out and results showed good matching. Nevertheless, it is important that a biomass powder simulation addresses overlapping/complicated... [more]

Amyloid beta peptide (Aβ)-related studies require an adequate supply of purified Aβ peptide. However, Aβ peptides are “difficult sequences” to synthesize chemically, and low yields are common due to aggregation during purification. Here, we demonstrate an easier synthesis, deprotection, reduction, cleavage, and purification process for Aβ(1-40) using standard 9-fluorenylmethyloxycarbonyl (Fmoc)-protected amino acids and solid-phase peptide synthesis (SPPS) resin [HMBA (4-hydroxymethyl benzamide) resin] that provides higher yields of Aβ(1-40) than previous standard protocols. Furthermore, purification requires a similar amount of time as conventional purification processes, although the peptide must be cleaved from the resin immediately prior to purification. The method described herein is not limited to the production of Aβ(1-40), and can be used to synthesize other easily-oxidized and aggregating sequences. Our proposed methodology will contribute to various fields using “difficult se... [more]

A numerical simulation study was carried out to study the combined thermal behavior and hydrodynamics of a pseudo-2D fluidized bed using a computational fluid dynamics−discrete element method (CFD-DEM). To mimic the effect of heterogeneous exothermic reactions, a constant heat source was implemented in the particle energy equation. The effects of superficial gas velocity, bed height and heat source distribution were analyzed with the aid of averaged volume fraction and temperature distributions and velocity profiles. It was found that both the gas superficial velocity and the bed aspect ratio have a profound influence on fluidization behavior and temperature distributions.

Monitoring process variables in bioprocesses with complex expression systems, such as filamentous fungi, requires a vast number of offline methods or sophisticated inline sensors. In this respect, cell viability is a crucial process variable determining the overall process performance. Thus, fast and precise tools for identification of key process deviations or transitions are needed. However, such reliable monitoring tools are still scarce to date or require sophisticated equipment. In this study, we used the commonly available size exclusion chromatography (SEC) HPLC technique to capture impurity release information in Penicillium chrysogenum bioprocesses. We exploited the impurity release information contained in UV chromatograms as fingerprints for development of principal component analysis (PCA) models to descriptively analyze the process trends. Prediction models using well established approaches, such as partial least squares (PLS), orthogonal PLS (OPLS) and principal component... [more]

In this work, we explore the synthesis of layered double hydroxide (LDH) particles containing different molar ratios of Gd3+ and Dy3+ cations. A single crystalline phase was obtained for Zn2.0Al0.75Gd0.125Dy0.125-LDH and Zn2.0Al0.5Gd0.25Dy0.25-LDH, and their efficiency as contrast agents was evaluated by T1- and T2-weighted magnetic resonance imaging (MRI). Both GdDy-LDHs exhibited longitudinal relaxivity (r1) higher than a commercial reference. The highest contrast in the T1 mode was achieved with the Zn2.0Al0.75Gd0.125Dy0.125-LDH, which contained the lowest concentration of lanthanides; this efficiency is related to the lowest amount of carbonate anions complexing the lanthanide sites. On the contrary, the best contrast in the T2 mode was achieved with Zn2.0Al0.5Gd0.25Dy0.25-LDH. Zn2.0Al0.75Gd0.125Dy0.125-LDH and Zn2.0Al0.5Gd0.25Dy0.25-LDH presented r2/r1 ratios of 7.9 and 22.5, respectively, indicating that the inclusion of gadolinium and dysprosium into layered structures is a prom... [more]

In this work, the transformation of urine into nutrients using electrolytic oxidation in a single-compartment electrochemical cell in galvanostatic mode was investigated. The electrolytic oxidation was performed using thin film anode materials: boron-doped diamond (BDD) and dimensionally stable anodes (DSA). The transformation of urine into nutrients was confirmed by the release of nitrate (NO3−) and ammonium (NH4+) ions during electrolytic treatment of synthetic urine aqueous solutions. The removal of chemical oxygen demand (COD) and total organic carbon (TOC) during electrolytic treatment confirmed the conversion of organic pollutants into biocompatible substances. Higher amounts of NO3− and NH4+ were released by electrolytic oxidation using BDD compared to DSA anodes. The removal of COD and TOC was faster using BDD anodes at different current densities. Active chlorine and chloramines were formed during electrolytic treatment, which is advantageous to deactivate any pathogenic micro... [more]

Size and thermal effect on molar heat capacity of liquid at constant volume (Cv) on a nanometer scale have been investigated by controlling the temperature and density of the liquid domain using equilibrium molecular dynamics (EMD) simulations. Lennard-Jones (LJ) type molecular model with confinement gap thickness (h) 0.585 nm to 27.8 nm has been used with the temperature (T) ranging from 100 K to 140 K. The simulation results revealed that the heat capacity of the nanoconfined liquid surpasses that of the bulk liquid within a defined interval of gap thickness; that the temperature at which maximum heat capacity occurs for a nanoconfined liquid vary with gap thickness following a power law, TCv,max = 193.4 × (h/a)−0.3431, ‘a’ being the lattice constant of Argon (solid) at 300 K; and that for a specified gap thickness and temperature, the confined liquid can exhibit a heat capacity that can be more than twice the heat capacity of the bulk liquid. The increase in heat capacity is underpi... [more]

The importance of fruit-derived resveratrol (RES) in the treatment of various diseases has been discussed in various research publications. Those research findings have indicated the ability of the molecule as therapeutic in the context of in vitro and in vivo conditions. Mostly, the application of RES in in vivo conditions, encapsulation processes have been carried out using various nanoparticles that are made of biocompatible biomaterials, which are easily digested or metabolized, and RES is absorbed effectively. These biomaterials are non-toxic and are safe to be used as components in the biotherapeutics. They are made from naturally available by-products of food materials like zein or corn or components of the physiological system as with lipids. The versatility of the RES nanoparticles in their different materials, working range sizes, specificity in their targeting in various human diseases, and the mechanisms associated with them are discussed in this review.

Due to climate change problems caused by greenhouse gas emissions generated by fossil fuels and from waste disposition, fuel alternatives for power generation are being extensively researched. Currently, in Brazil and in many countries, wood waste is disposed in landfills. However, due to lignin, one of the major constituents of biomass, which prevents wood waste from suffering microbial degradation, there is no significant mass degradation, even over decades, when landfilled. Hence, landfilling is not a solution to discard wood waste. Hence, one of the solutions to get rid of the great amount of wood waste is to use it as feedstock in waste-to-electricity (WTE) projects. WTE projects are in high demand in the world, as they can replace fossil fuels and they reduce two major environmental problems (greenhouse gas emissions due to the use of fossil fuels and the accumulation of waste in landfills), while generating biofuels and/or electricity. One of the residues that can be used in WTE... [more]

Machining processes are critical and widely used components in the manufacturing industry because they help to precisely make products and reduce production time. To keep the previous advantages, a machine tool should be installed at the designated place and condition of the machine tool should be maintained appropriately to working environment. In various maintenance methods for keeping the condition of machine tool, condition-based maintenance can be robust to unpredicted accidents and reduce maintenance costs. Tool monitoring and diagnosis are some of the most important components of the condition based maintenance. This paper proposes stacked auto-encoder based CNC machine tool diagnosis using discrete wavelet transform feature extraction to diagnose a machine tool. The diagnosis model, which only uses cutting force data, cannot sufficiently reflects tool condition. Hence, we modeled diagnosis model using features extracted from a cutting force, a current signal, and coefficients o... [more]

Twenty fluorescent Pseudomonas isolates were tested for their ability to produce siderophores on chrome azurol S (CAS) agar plates and their antagonistic activity against six plant pathogenic fungal isolates was assessed. Scaling-up production of siderophores from the promising isolates, P. aeruginosa F2 and P. fluorescens JY3 was performed using batch and exponential fed-batch fermentation. Finally, culture broth of the investigated bacterial isolates was used for the preparation of two economical bioformulations for controlling Fusarium oxysporum and Rhizoctonia solani. The results showed that both isolates yielded high siderophore production and they were more effective in inhibiting the mycelial growth of the tested fungi compared to the other bacterial isolates. Exponential fed-batch fermentation gave higher siderophore concentrations (estimated in 10 µL), which reached 67.05% at 46 h and 45.59% at 48 h for isolates F2 and JY3, respectively, than batch fermentation. Formulated P.... [more]

In this study, we evaluate potato pulp waste as a potential raw material for obtaining yeast biomass. A portion of the carbohydrates in the potato pulp waste can thereby be converted into more valuable protein. The potato pulp waste was analyzed in terms of protein and ash content, dry mass, simple sugars, and starch content. Two kinds of hydrolysis were performed (thermo-acidic and enzymatic) to produce media for cultivating Candida guilliermondii and Pichia stipitis. The hydrolysates and post-cultivation leachates were analyzed by High Performance Liquid Chromatography (HPLC). The highest biomass yield after 48 h (39.3%) was noted for Candida guilliermondii yeast grown on enzymatic hydrolysate-based medium. Our results prove that potato waste pulp is a promising raw material for the production of yeast single-cell protein (SCP).

Cell-free protein synthesis (CFPS) is an emerging tool for the rapid production of difficult-to-express proteins as well as for identifying protein synthesis bottlenecks. In CFPS, the biotic phase is substituted by extracts of living cells devoid of any of their own genetic material. The main advantage is that these systems delineate cell growth from recombinant protein production, enabling the expression of targets that would otherwise place too big a burden on living cells. We have conducted a techno-economic analysis of a CFPS system to produce monoclonal antibodies (mAbs) using extracts of Chinese hamster ovary (CHO) cells. We compare the performance of the CFPS system with two alternative production strategies: stable and transient gene expression in CHO cells. Our assessment shows that the viability of CFPS for mAb production requires a significant increase in the product yield and the recycling of high-cost components such as DNA. Nevertheless, CFPS shows significant promise for... [more]