Geothermal heating is considered to be one of the low-carbon-energy technologies for building heating. Aiming at the problem that the operating cost and investment cost of geothermal heating systems are still high, the conventional geothermal heating system coupled with energy storage for office building heating is studied in this paper. Four operational strategy models of the coupled system are established based on time-of-use electricity prices. A genetic algorithm is used to find the optimal value of each decision variable using minimization of levelized cost of heat (LCOH) as the objective function. The influences of electricity and equipment prices on the optimal values of the decision variables are discussed. Four operation strategies are investigated. If only operating cost is considered in the optimization, comparison shows that the best operation strategy is the one giving high priority to use the energy storage tank for heating during the peak electricity period. However, if... [more]

Spatial separation into acidogenic and methanogenic stages is considered a viable option to ensure process stability, energy efficiency and the better control of key anaerobic digestion (AD) parameters. The elucidation of the optimal modes of two-stage AD for the maximization of the recovery of biofuels (H2 and CH4) is still an urgent task, the main optimization criteria being the highest energy yield (EY) and energy production rate (EPR). In this work, a response surface methodology was used for an optimization of energy production from the two-stage mesophilic−thermophilic AD of cheese whey (CW). Three dilution rates of CW, providing values of 10.9, 14.53 and 21.8 g for the chemical oxygen demand (COD)/L in the influent and three hydraulic retention times (HRTs) (1, 2 and 3 days) in methanogenic biofilters at a constant HRT in an acidogenic biofilter of 0.42 days, were tested to optimize the EY and EPR. The desirability approach produced combined optimum conditions as follows: the di... [more]

The present study utilizes a density-based topology optimization method to design a serpentine channel under turbulent flow, solving a high pressure loss issue and enhancing heat transfer capability. In the topology optimization, the k−ε turbulence model is modified by adding penalization terms to reveal turbulence effects. Heat transfer modeling is included by setting the modified energy equation with additional terms related to topology optimization. The main objective is to minimize pressure loss while restricting heat transfer. The 2D simplified model is topologically optimized. Then, the optimal solution with intermediate results is extruded in the 3D system and interpreted with triply periodic minimal surfaces (TPMS) to further enhance heat transfer performance. Compared to the baseline serpentine channel, the optimized model infilled with the diamond-TPMS structure lowers pressure loss by 30.8% and significantly enhances total heat transfer by up to 45.8%, yielding thermal perfo... [more]

As a typical representative of the stator permanent magnet (PM) machines, the flux reversal machines (FRMs) have a simple structure, high availability of PMs, and high efficiency, making them suitable for direct drive applications. However, the PMs of the FRMs are mounted on the surface of the stator tooth, and its equivalent length of air gap is relatively large, which limits the torque increase. To improve the torque density, a novel FRM with auxiliary teeth is proposed in this paper. Half of the stator teeth are replaced by auxiliary teeth without PMs to reduce magnetic flux leakage, the number of PMs on each stator tooth is also changed. To improve the torque, the genetic algorithm is used to optimize the key design parameters to determine the optimal parameters of the machine. Finally, a finite element model is established to verify the analysis results. Compared with the conventional FRM, the torque of the proposed FRM is increased by 25.1%, the torque ripple is reduced by 24.1%,... [more]

Wireless sensor networks (WSNs) are considerably used for various environmental sensing applications. The architecture and internal specifications of WSNs have been chosen based on the requirements of particular applications. On this basis, WSNs consist of resource (energy and memory)-limited wireless sensor nodes. WSNs initiate data communication from source to destination via physical layer management principles, channel slot scheduling principles (time division multiple access), wireless medium access control (WMAC) protocols, wireless routing protocols and application protocols. In this environment, the development of WMAC principles, routing protocols and channel allotment schemes play crucial roles in network communication phases. Consequently, these layering functions consume more energy at each sensor node, which leads to minimal network lifetime. Even though the channel management schemes, medium control protocols and routing protocols are functionally suitable, the excessive... [more]

The effective deployment of electrical energy has received attention because of its environmental implications. On the other hand, induction motors are the primary equipment used in many industries. Industrial facilities demand the maximum percentage of energy. This energy demand is determined by the operating circumstances imposed by the internal characteristics of the induction motor. Because internal parameters of an induction motor are not immediately measurable, they must be obtained through an identification process. This paper proposed an improved version of moth flame optimization (IMFO) for the efficient parameter estimation of induction motors. A steady-state equivalent circuit of the induction motor is employed for the simulation. The proposed technique handles the parameter estimation problem better than moth flame optimization (MFO), particle swarm optimization (PSO), the flower pollination algorithm (FPA), the tunicate swarm algorithm (TSA), and the sine cosine algorithm... [more]

To investigate the effect of the target weight coefficient on the structure design of the micro-channel heat sink, an innovative method for the topology optimization design of micro-channel structures with different bifurcation angles is adopted. In this study, the improved interpolation function, density filtering, and hyperbolic tangent projection methods are adopted to obtain a clear topological structure of the micro-channel heat sink. The heat transfer of the micro-channel heat sink under different bifurcation angles is compared. At the same time, the influence of the two different objective functions, heat transfer, and flow energy consumption, is analyzed in the topology optimization of micro-channel heat sinks. The results show that when the bifurcation angle is 135°, both the heat transfer and the average outlet temperature of the micro-channel heat sink obtain the maximum value, and the heat transfer effect is the best. With the increase of the heat transfer weighting coeffic... [more]

Knowledge of the influence of factors determining energy consumption in buildings is very important for the possibility of effective energy saving. This article describes the results of an original study on the analysis of the annual energy demand for heating (QH;nd), cooling (QC;nd), and annual usable energy demand (QH/C;nd = QH;nd + QC;nd) assumed as objective functions of a designed single-family building, which can be classified as a typical representative of currently built houses in Poland. It was assumed that the object of study was located in the climatic conditions of north-eastern Poland. The study takes into consideration three groups of selected parameters: architectural/spatial, structural, and physical properties of windows. The research was carried out in a single-family building, as energy consumption in residential buildings accounts for a significant part of the total energy consumption in buildings. In the group of architectural/spatial parameters, the heig... [more]

Renewable energy sources have power quality and stability issues despite having vast benefits when integrated with the utility grid. High currents and voltages are introduced during the disconnection or injection from or into the power system. Due to excessive inverter switching frequencies, distorted voltage waveforms and high distortions in the output current may be observed. Hence, advancing intelligent and robust optimization techniques along with advanced controllers is the need of the hour. Therefore, this article presents an improved arithmetic optimization algorithm and an offset hysteresis band current controller. Conventional hysteresis band current controllers (CHCCs) offer substantial advantages such as fast dynamic response, over-current, and robustness in response to impedance variations, but they suffer from variable switching frequency. The offset hysteresis band current controller utilizes the zero-crossing time of the current error for calculating the lower/upper hyst... [more]

Nuclear power plants have a complex structure and changeable operation mode, which induces low setting calculation efficiency. After analyzing the technology, architecture, and functional logic of a variety of relay protection setting calculation systems and combining the characteristics of the setting calculation of nuclear power plants, the relay protection setting calculation system in nuclear power plants based on B/S architecture and cloud computing is studied in this paper. The system adopts three-tier B/S architecture, applies two key technologies, the cloud computing task distribution synchronization mechanism and the cloud component automatic assembly mechanism, and introduces a particle swarm optimization algorithm to provide technical support for nuclear power plant setting calculation; the running example of the nuclear power plant system fully proves the efficiency and reliability of the relay protection setting calculation system of the nuclear power plant, which has high... [more]

Transient electromagnetic (TEM) surveys constitute an important element in exploration projects and can be successfully used in the search for oil and gas. Different modifications of the method include shallow (sTEM), 2D, 3D, and 4D (time-lapse) soundings. TEM data allow for solving a large scope of problems for estimating resources and reserves of hydrocarbons, discriminating reservoir rocks, detecting tectonic features, and characterizing drilling conditions. TEM surveys are applicable at all stages, from initial prospecting to production, and are especially efficient when combined with seismic surveys. Each stage has its specific objectives: estimation of net pay thickness, porosity, and fluid type during prospecting, optimization of well placement and prediction of drilling conditions in exploration, and monitoring of flooding during production. Electromagnetic soundings resolve permafrost features well and thus have a high potentiality for exploration in the Arctic petroleum provi... [more]

The high penetration of photovoltaic solar generation and electric vehicles in developing countries and with vertically integrated electricity markets with restrictive regulatory policies enhance demand management and the participation of prosumers in optimizing their resources. In this sense, the research presents a demand management methodology based on the prosumer model for recharging electric vehicles through optimization based on linear programming to minimize recharging costs, considering the stochasticity of the solar radiation variables, vehicular mobility patterns, consumer preferences, and optimal location of charging stations through surveys and predictive tools such as PVsyst and GAMS, in such a way that the energy demand for recharging electric vehicles is met. This way, the methodology reduces power demand peaks and mitigates the economic and technical impact on distribution networks. This case study has been modelled with real information from electric vehicles, distrib... [more]

The present study investigates low-grade heat utilization in ejector refrigeration systems under hot climatic conditions. A variable area ejector is used to maximize the harvested heat from the generator of the solar system at peak times. Exergy, economic, and exergoeconomic analyses are conducted to evaluate the performance of the system. A thermodynamic model of the system has been developed using Ebsilon Professional software. Available experimental and theoretical data validate the results. The effects of properties of the working fluids, ejector geometry, and operation conditions are also evaluated. It was found that the coefficient of performance of the system reached 0.45 at a generator pressure of 3 bars. Furthermore, it was noticed that the overall exergy efficiency could be increased for a fixed generator temperature while increasing the ejector area ratio. A value of 21% exergetic efficiency was calculated for the system. The exergoeconomic analysis of the system demonstrate... [more]

Wireless charging systems (WCSs) are considered very appropriate to recharge underwater surface vehicles (USVs) due to their safe, flexible, and cost-effective characteristics. The small depth of immersion of USVs allows a WCS operated at an mm-level distance using a dock. Resultant tight coupling between the transmitter and receiver is conducive to high power, yet faces a challenge to alleviating misalignment sensitivity. In addition, considering USVs’ endurance, the weight of a WCS should be strictly limited. In this paper, a 6.0 kW underwater WCS is analyzed, designed, and optimized, which achieves a good balance of power capacity, misalignment tolerance, and onboard weight. A multi-receiving-coil structure is employed, which is crucial to large misalignment tolerance. On this basis, two types of coils adapting the hull shape of USV, viz., curved and quasi-curved coils, are devised and compared in case the hydrodynamic performance of USV is degraded. Finally, the weight of receiver... [more]

Energy system models that consider variable renewable energy sources (VRESs) are computationally complex. The greater spatial scope and level of detail entailed in the models exacerbates complexity. As a complexity-reduction approach, this paper considers the simultaneous spatial and technological aggregation of energy system models. To that end, a novel two-step aggregation scheme is introduced. First, model regions are spatially aggregated to obtain a reduced region set. The aggregation is based on model parameters such as VRES time series, capacities, etc. In addition, spatial contiguity of regions is considered. Next, technological aggregation is performed on each VRES, in each region, based on their time series. The aggregations’ impact on accuracy and complexity of a cost-optimal, European energy system model is analyzed. The model is aggregated to obtain different combinations of numbers of regions and VRES types. Results are benchmarked against an initial resolution of 96 regio... [more]

Optimal power flow is one of the fundamental optimal operation problems for power systems. With the increasing scale of solar energy integrated into power systems, the uncertainty of solar power brings intractable challenges to the power system operation. The multi-objective optimal power flow (MOOPF) considering the solar energy becomes a hotspot issue. In this study, a MOOPF model considering the uncertainty of solar power is proposed. Both scenarios of overestimation and underestimation of solar power are modeled and penalized in the form of operating cost. In order to solve this multi-objective optimization model effectively, this study proposes a clustering-based multi-objective differential evolution (CMODE) which is based on the main features: (1) extending DE into multi-objective algorithm, (2) introducing the feasible solution priority technique to deal with different constraints, and (3) combining the feasible solution priority technique and the merged hierarchical clustering... [more]

With the application of microdevices in the building engineering, aerospace industry, electronic devices, nuclear energy, and so on, the dissipation of high heat flux has become an urgent problem to be solved. Microchannel heat sinks have become an effective means of thermal management for microdevices and enhancements for equipment due to their higher heat transfer and small scale. However, because of the increasing requirements of microdevices for thermal load and temperature control and energy savings, high efficiency heat exchangers, especially microchannels are receiving more and more attention. To further improve the performance of microchannels, optimizing the channel geometry has become a very important passive technology to effectively enhance the heat transfer of the microchannel heat sink. Therefore, in this paper, the microchannel geometry characteristics of previous studies are reviewed, classified and summarized. The review is mainly focused on microchannel geometry featu... [more]

Engineered water surfactant flooding (EWSF) is a novel EOR technique to reduce residual oil saturation; however, it becomes quite challenging to obtain Winsor Type III microemulsion and the lowest IFT under actual reservoir conditions if only low salinity water is used. The main objective of this study was to design a negative salinity gradient to optimize the performance of the hybrid method. Three corefloods were performed on carbonate outcrop samples. The injection sequence in the first test was conventional waterflooding followed by optimum engineered water injection (2900 ppm) and finally an EWSF stage. The second and third tests were conducted using a varying negative salinity gradient. Engineered water for this study was designed by 10 times dilution of Caspian Sea water and spiking with key active ions. A higher salinity gradient was used for the first negative salinity gradient test. A total of 4300 ppm brine with 1 wt% surfactant was injected as a pre-flush after waterfloodin... [more]

A novel asymmetric spoke-type interior permanent magnet (AS-IPM) machine is proposed in this paper. It utilizes the magnetic-field-shifting (MFS) effect to improve the torque performance, which achieves a high utilization ratio of both permanent magnet (PM) torque and reluctance torque. In addition, a general pattern of rotor topologies is proposed to represent all possible machine structures. Various rotor structures can be obtained by changing the design parameters of the general pattern. A non-dominated sorting genetic algorithm II (NSGA-II) is adopted to automatically search for optimal rotor configurations. With the aid of the optimization program, an asymmetric spoke-type rotor structure with improved performance is obtained. To showcase the advantages of the proposed machine, the electromagnetic performance is compared between a conventional spoke-type interior permanent magnet (S-IPM) machine and a proposed AS-IPM machine. The finite-element simulation results show that the opt... [more]

The axial-flow pump is a widely used piece of general machinery which consumes large amounts of energy. In this study, an axial-flow pump with the specific speed of 536 is firstly designed and experimentally measured; then, the orthogonal method is employed to conduct the energy performance optimization. Five optimization parameters, including hub control point, hub stagger angle, shroud stagger angle, camber angle and centroid position were set with four levels. Sixteen individual pumps were designed according to the orthogonal method; then, a numerical simulation was implemented to obtain the energy performance and flow pattern. Results showed that the shroud stagger angle has the maximum influence on the pump head and efficiency, and the hub stagger angle and camber angle are also very important. At a design point of flow rate 70 kg/s, the efficiency of the optimal pump is 86.29%, which improved by 2.05% in comparison with the baseline pump. The pressure gradient of the optimal pump... [more]

With the background of implementing carbon peaking and carbon neutralization, identifying methods to realize energy-saving and carbon reduction effectively has become an important issue in the intelligent energy-conservation manufacturing industry. During the process of achieving this goal, determining an optimal location for a low-carbon and intelligent manufacturing industrial park is a foremost decision-making problem for manufacturing corporations’ energy-efficient development. The article established a multi-criteria decision framework to assist manufacturing companies when selecting suitable industrial park sites. To begin with, an evaluation criteria framework is confirmed by literature search. Then, a fuzzy optimization model, which combines the fuzzy Technique for Order of Preference by Similarity to Ideal Solution (TOPSIS) and the fuzzy VlseKriterijumska Optimizacija I Kompromisno Resenje (VIKOR) is presented, where fuzzy TOPSIS is used to determine the decision-maker criteri... [more]

The closed evaporative cooling tower (CECT) is widely used in the field of industrial cooling. At present, most CECTs still mainly adopt the horizontal-tube falling-film cooling method. In this paper, a novel vertical CECT using 3D deformation tubes is developed. To investigate the vertical surface falling-film evaporative cooling effect of this novel cooling equipment, a traditional horizontal CECT was modified to produce a prototype of vertical non-packing CECT. The cooling performance of the novel vertical CECT has been investigated and compared to the previous traditional horizontal CECT by experimental method. The results show that the convective heat transfer coefficient of the water film outside the tube was increased by 5.87~12.95% and the overall cooling performance was increased by 7.31% on average. This indicates that the cooling load can be increased by changing the traditional horizontal-tube falling-film evaporative cooling method to the vertical falling-film evaporative... [more]

In this paper, a heuristic approach to doubly fed induction generator (DFIG) protection and low voltage ride through (LVRT) is carried out. DFIG-based wind systems are rapidly penetrating the power generation section. Despite their advantages, their direct coupling grid makes them highly sensitive to symmetrical faults. A well-known solution to this is the crowbar method of DFIG protection. This paper provides a method to determine the optimal crowbar resistance value, to ensure a strong trade-off between the rotor current and DC voltage transients. Further, since the crowbar method requires disconnection from the grid, the linear quadratic regulator (LQR) is applied to the system. This is to ensure fault ride through compliance with recent grid code requirements. The well-known PSO, as well as the recently developed African vultures optimization algorithm (AVOA), was applied to the problem. The first set of results show that for severe symmetrical voltage dips, the AVOA provides a goo... [more]

As an important part of carbon dioxide capture, utilization and storage (CCUS), the progress of injecting CO2 into oil reservoirs could increase the recovery rate and achieve large-scale carbon storage. It has become one of the most important carbon storage methods around the world. This paper selected the tight sandstone of the fourth member of the Quantou Formation in the southern Songliao Basin to carry out a CO2 storage physical simulation experiment. Representative samples were collected at 24 h, 72 h, 192 h and 432 h to study the CO2 water-rock interaction and to analyze the mineral composition, pore structure and the evolutionary characteristics of physical reservoir properties over time. Physical property analysis, Ion analysis, X-ray diffraction mineral analysis, QEMSCAN mineral analysis, scanning electron microscopy and high-resolution CT scanning techniques were adopted. The main points of understanding were: (i) It shows a differential evolution of different minerals follow... [more]

In the present work, numerical simulation and optimization was carried out to analyze the mechanism of the variable guide vanes (VGVs) of a transonic compressor. A seven-stage transonic compressor including three-stage VGVs was studied. The VGVs were adjusted individually and jointly under different IGV opening degrees. Changes in performance and shock wave were analyzed, and the coupling effect of the VGV joint adjustment was summarized. Aiming at the maximum efficiency, the joint turning angles were optimized. A novel phenomenon was found wherein the VGV adjustment can affect not only its own performance and that of adjacent downstream blades, but also that of upstream blades. Incidence and performance of upstream blades are improved, but those of the VGV and its adjacent downstream blades are deteriorated. VGV adjustment weakens the shock wave and shock-induced boundary layer separation. The optimal solution for VGV joint adjustment is the combination of the optimal solutions for si... [more]