Despite the climate commitments made by countries in the Paris Climate Agreement adopted in 2015 and reinforced during COP 21 and with notably less success during COP 22, world carbon emissions increased in both 2021 and 2022. It is increasingly unlikely that the world will achieve the targeted 50% carbon reduction by 2030, the reduction approximately needed for reducing global temperature rise since the beginning of the Industrial Revolution to less than 1.5 deg. C. At the same time, there remain nearly 2 billion people in the world who have no or highly unreliable access to power. In developed countries, access to both clean energy and energy efficiency investment in residences within low to moderate income communities has also lagged. This paper provides a review of the “Productive Use of Energy (PUE)”, which is a means to add value to solar energy mini- and micro-grids to ensure investment worthiness and add more value to the communities being served. In this context, it posits an... [more]

The issues of low accuracy, poor generality, high cost of transformer fault early warning, and the subjective nature of empirical judgments made by field maintenance personnel are difficult to solve with the traditional measurement methods used during the development of the transformer. To construct a transformer fault early warning analysis, this study recommends a data-fusion-based decision tree approach for merging electrical quantity signals with a non-electrical amount of vibration signals. By merging a decision tree inference with actual operation data, a clustering center, and an early warning model, this method creates a transformer fault early warning model with self-learning ability and adaptive capabilities. After reasonable verification, the method becomes more universal and interpretable, and it can successfully conduct an early warning of transformer faults.

Although rooftop PV panels and battery energy storage systems have been well established for detached residential buildings, there is still a lack of access to the advantages of onsite renewable energy generation and consumption for residents of multi-unit buildings. To understand the effects of developing distributed renewable energy sources for multi-unit buildings, a new fair energy-sharing model in which different groups of residents can gain benefit from the shared energy systems is proposed. Despite the potential benefits of developing renewable technologies in multi-unit buildings, the energy trading and allocation processes in the buildings can be unfair for some groups of residents. Accordingly, this work studies the main principles of energy justice and analyses how these principles can be applied in the energy trading and allocation processes to achieve fair energy sharing. In addition to fairness and justice, the experimental results show that our method increases the selle... [more]

In order to solve the problem of wax deposition in waxy crude oil from the Daqing oilfield, cold fingers were used in the experimentation. Compared with other methods, the cold finger method is simple, easy to operate, and takes little space. Measurements of wax deposition with temperature, temperature differences between the crude oil and the wall, deposition time, and cold finger rotation rate were made. The results showed that the deposition rate is up to 0.35 g/h at 8−24 h. The maximum deposition rate at 90 rotations/min was 0.26 g/h, which is 3% higher than the minimum deposition rate.

Plasma-facing components (PFCs) are used as the barrier to the beam of high heat flux generated due to nuclear fusion. Therefore, efficient cooling of PFCs is required for safety and smooth operation of a fusion reactor. The Hyper Vapotron (HV) is generally used as the heat exchanger to cool down the PFCs during operation. These heat exchangers use pool and flow boiling mechanisms, and hence, their ability is inherently constrained by critical heat flux (CHF). The boiling of nanofluid is very promising as the working fluid in the HV. The efficiency of the HV increases due to the increase in CHF by applying nanofluids. However, the feasibility of nanofluid cooling in fusion reactors needs proper understanding. This paper reviews the recent developments in the utilization of boiling phenomena in nanofluid as a coolant in the HV. Experiments, theoretical studies, significant achievements, and challenges are analyzed and discussed. Finally, important points are indicated for future researc... [more]

The solar carbo-thermal and methano-thermal reduction of both MgO and ZnO were performed in a flexible solar reactor operated at low pressure through both batch and continuous operations. The pyro-metallurgical process is an attractive sustainable pathway to convert and store concentrated solar energy into high-value metal commodities and fuels. Substituting fossil fuel combustion with solar energy when providing high-temperature process heat is a relevant option for green extractive metallurgy. In this study, a thermodynamic equilibrium analysis was first performed to compare the thermochemical reduction of MgO and ZnO with solid carbon or gaseous methane, and to determine the product distribution as a function of the operating conditions. The carbo-thermal and methano-thermal reduction of the MgO and ZnO volatile oxides was then experimentally assessed and compared using a directly irradiated cavity-type solar reactor under different operating conditions, varying the type of carbon-b... [more]

In gasoline-driven vehicles, fuel vapor retaining systems are used to prevent the emission of hydrocarbons from the fuel tank into the atmosphere. In this paper, which is Part 2 of our publication, measurements of regeneration processes of the activated carbon by flushing it with humid nitrogen gas of 70% relative humidity are represented. Using purge air with high relative humidities, representing realistic conditions, it can be observed that water is accumulated in the activated carbon. For ethanol-containing fuel blends, additional accumulation of ethanol in the carbon occurs, decreasing the adsorption capacity of the carbon for standard fuel’s components considerably. State-of-the-art testing procedures use purge air with about 50% relative humidity for the regeneration of the activated carbon filters. As this often does not represent real operation conditions, the working limits of the fuel vapor retaining systems could not be identified up to now. Furthermore, the determination o... [more]

With the maturation of silicon-based technologies, silicon solar cells have achieved a high conversion efficiency that approaches the theoretical limit. Currently, great efforts are being made to enhance the reliability of silicon solar cells. When the silicon solar cells are made into modules, potential-induced-degradation (PID) occurs during operation because of the high voltage applied between the frame and the cells, which reduces the efficiency and output power. The diffusion of Na+ ions from the front glass and the increased leakage current along the migration path are the major causes of PID. In this work, atomic layer deposition (ALD)-grown amorphous thin Al2O3 layers are introduced underneath the front glass to prevent the diffusion of Na+ ions and the resulting PID. Accelerated PID tests showed that an ALD-grown Al2O3 layer of 30 nm could effectively suppress PID seriously affecting the conversion efficiency or light transmittance. The introduction of an ion-diffusion barrier... [more]

This article presents the application of a novel system for the treatment of fruit and vegetable waste (FVW) using the combination of treatment by the application of the liquid fraction to an anaerobic hydrolytic bioreactor and a constructed wetland. The batch-fed anaerobic bioreactor (AB) had an average organic loading rate of 44 g COD/L-d and a hydraulic residence time (HRT) of 24 h for the degradation of the liquid fraction of the FVW with an average COD removal of 55%. Subsequently, the constructed wetlands (CWs) were fed a subsurface vertical flow of the effluent from the AB by stepwise concentration increments from 1 to 12 g COD/L and a HRT = 72 h until the limit conditions of the operation were identified. For the tropical ornamental species of the CWs in red volcanic gravel (RVG) and RVG + polyethylene (PE) supports, the monoculture of Hippeastrum rutilum and Spathiphyllum wallisii presented removals of COD, Tot-P, and TKN of 90%, 80%, and 85%, respectively. The polycultures wi... [more]

The air temperature variation of a closed room, well insulated, during the initial time of operation of air-conditioning systems up to temperature stabilization, is simulated by a two-dimensional integral model as a quasi-steady-state phenomenon. The model equipped with a conservation equation for tracer concentration or relative temperature, including the stratification parameter, is well qualified. The flow leaving the air conditioning device forms an inclined buoyant jet which bends over and meets the room floor, where it spreads sideways forming a layer with jet temperature. A sequence of layers, which affect the jet temperature through entrainment, are produced by a novel bottom-up technique. The layer air temperatures are calculated through the bulk dilution of a near bottom jet cross-section, which feeds each new layer. The model simulated a real case and predicted the transient variation of room air and buoyant jet temperatures up to stabilisation. It also predicted the time ne... [more]

Shared manufacturing provides a new path for the transformation and development of the manufacturing industry, but challenges such as low quality and poor positivity for quality improvement limit the positive role of shared manufacturing. Considering the influences of heterogeneous emotions of subjects on quality decision making, the theory of rank-dependent expected utility (RDEU) and evolutionary game theory were integrated to establish an evolutionary game model of shared manufacturing quality innovation synergy with multi-agent participation and analyze how sentiment affects motivation for quality improvement. The study showed that: (1) emotions, an irrational factor, can significantly change the stable state of the evolution of the shared manufacturing quality innovation synergetic system by influencing the decision-making behavior of decision makers; (2) in terms of the specific microscopic influence mechanism, rationality is the key to ensuring that the behavioral decisions of d... [more]

For long-distance and bulk-power delivery of new energy, high-voltage direct current (HVDC) is a more effective way than high-voltage alternative current (HVAC). In view of the current capacity disparity between line commutated converter (LCC) and voltage source converter (VSC), a hybrid hierarchical HVDC topology with parallel operation of 800 kV and 400 kV DC lines is investigated. The optimal current allocation method for hybrid hierarchical HVDC is proposed distinct from the same rated current command configuration method of high-voltage and low-voltage converters in traditional topology. Considering the transmission loss reduction of the HVDC system, a multi-order fitting function of transmission loss including LCC converter stations, VSC converter stations and DC lines is established. To minimize the transmission loss and the voltage deviation of key DC nodes comprehensively, a multi-objective genetic algorithm and maximum satisfaction method are utilized to obtain the optimal al... [more]

This paper presents a soft switching direct current (DC) converter, with the benefits of bidirectional power conversion and wide-ranging voltage operation for battery charging and discharging capability. A series resonant circuit with variable switching frequency modulation is used to achieve the advantages of soft switching turn-on or turn-off of semiconductor devices. Therefore, the switching power losses in power devices can be reduced. A symmetric resonant circuit topology with a capacitor−inductor−inductor−capacitor (CLLC) structure is adopted to achieve a bidirectional power conversion capability for battery storage units in electric vehicle applications. Due to the symmetric circuit structure on both input and output sides, the converter has similar voltage gains for each power flow operation. In order to overcome the drawback of narrow voltage range operation in conventional resonant converters, a variable transformer turns ratio is adopted in the circuit, to achieve wide outpu... [more]

In Germany, the number of small wood-burning combustion plants was around 11 million in 2020. The PM2.5 immissions caused by the operation of these combustion plants are already about as high as those from traffic exhaust gases. Thus, particulate matter immissions occur not only on busy roads but also in residential areas. Since there are few official measuring stations for PM2.5 in residential areas and suburbs, this study determined PM2.5 concentrations from November 2020 to June 2021 at three stations (urban, suburban, and residential) in the Karlsruhe area. Simultaneous measurements of PM2.5 at the three locations have been implemented to determine short-term (peaks), medium-term, and long-term particulate matter levels and to assign them to sources by observation, considering wind direction. Illustratively, PM2.5 immission levels in January and May 2021 were compared in this paper. The comparison of the particulate matter immissions measured in the urban and residential area in Ja... [more]

Over the last decade, the conical mill has emerged as a potential piece of equipment to use for continuous dry coating pharmaceutical powders. In this work, silicon dioxide was used as a guest particle on two excipients, fast flow lactose (FFL) and grade PH200 microcrystalline cellulose (MCC), for dry coating by a conical mill with a modified screen that permitted batch and continuous mode operation. Samples were pre-processed in a V-blender. SEM images, particle size distribution, and EDS mapping were used to characterise the treated powders. Pre-processed samples showed some discrete coating of the host particle. After batch processing, the samples were covered with a complete coating. When processed at high impeller speed, coating of FFL was a mix of A200P and FFL fines generated by attrition. Continuous mode processed samples, which had a lower processing time, were coated discretely and showed a better coating than the pre-processed samples. Increasing guest/host mass ratio with F... [more]

Adeno-associated virus vectors (AAV) are reported to have a great potential for gene therapy, however, a major bottleneck for this kind of therapy is the limitation of production capacity. Higher specific AAV vector yield is often reported for adherent cell systems compared to cells in suspension, and a microcarrier-based culture is well established for the culture of anchored cells on a larger scale. The purpose of the present study was to explore how microcarrier cultures could provide a solution for the production of AAV vectors based on the triple plasmid transfection of HEK293T cells in a stirred tank bioreactor. In the present study, cells were grown and expanded in suspension, offering the ease of this type of operation, and were then anchored on microcarriers in order to proceed with transfection of the plasmids for transient AAV vector production. This process was developed in view of a bioreactor application in a 200 mL stirred-tank vessel where shear stress aspects were stud... [more]

The construction of underground gas storage mostly focuses on depleted gas reservoirs. However, the depleted gas reservoir used to build underground gas storage in China is located far from the main gas consumption economic zone. It is necessary to reconstruct underground gas storage using nearby reservoirs in order to meet the needs of economic development. The complex three-phase seepage characteristics encountered in the process of reconstruction of underground gas storage reservoirs seriously affect their storage and injection production capacities. Combined with the mechanism of multiphase seepage and the multicycle injection production mode during the process of gas storage construction, the feasibility of rebuilding gas storage in medium- and low-permeability reservoirs was evaluated through relative permeability experiments and core injection production experiments. The results showed that the mutual driving of two-phase oil−water systems will affect the storage space and seepa... [more]

Hydrogenation of ethylene carbonate (EC) to co-produce methanol (MeOH) and ethylene glycol (EG) offers an atomically economic route for CO2 utilization. Herein, aided with bench and pilot plant data, we established engineering a kinetics model and multiscale reactor models for heterogeneous EC hydrogenation using representative industrial-type reactors. Model-based analysis indicates that single-stage adiabatic reactors, despite a moderate temperature rise of 12 K, suffer from a narrow operational window delimited by EC condensation at lower temperatures and intense secondary EG hydrogenation at higher temperatures. Boiling water cooled multi-tubular reactors feature near-isothermal operation and exhibit better operability, especially under high pressure and low space velocity. Conduction oil-cooled reactors show U-type axial temperature profiles, rendering even wider operational windows regarding coolant temperatures than the water-cooled reactor. The revelation of operational charact... [more]

China is taking initiative in energy transition to cope with the long-term controversy of its enormous energy consumption, aiming to use less carbon. Wind power, especially offshore wind energy, has become a prevailing alternative due to its low carbon emissions, renewability, competitiveness, and operation security. The layout of a transmission channel is a key consideration in marine project implementation. This paper investigates the technical characteristics, application status, and viable advantages of a conventional AC transmission, voltage source converter-based high-voltage direct current (VSC-HVDC) transmission, gas-insulated line (GIL) transmission, and hybrid HVDC transmission. A component-resolved evaluation model was proposed to estimate the costs to be incurred of four electrical transmission options for offshore wind power along the coast of Eastern China, with technical feasibility and economical considerations. Cost comparisons and component sensitivity analyses were d... [more]

Medium-depth and deep geothermal energy has been widely used because of its abundant resources and supply stability. Recently, attention has been given to the closed-loop heat extraction system using a deep borehole heat exchanger (DBHE), which enables geothermal energy to be harnessed almost everywhere. In this study, a check valve is adopted in a DBHE system in which the whole section of the well is used for heat extraction in winter during building heating and the upper part of the well is used for heat injection in summer during building cooling. The influence of injected water flowrates, water inlet temperatures, depths of the check valve and formation of thermal conductivities on the performance of this novel DBHE system has been investigated. It is found that heat injection through the upper part of the well in summer can improve the heat extraction rates to a certain extent during the heating season. In summer, the inlet temperature of water has a great influence on the heat in... [more]

The management of the liquid fraction of digestate produced from the anaerobic digestion of biodegradable municipal solid waste is a difficult affair, as its land application is limited due to high ammonium concentrations and the municipal waste that water treatment plants struggle to treat due to high pollutant loads. The amount of leachate and the pollutant load in the leachate produced by landfills usually decreases with the time, which increases the capacity of landfill leachate treatment plants (LLTPs) to treat additional wastewater. In order to solve the above two challenges, the co-treatment of landfill leachate and the liquid fraction of anaerobic digestate in an industrial-scale LLTP was investigated along with the long-term impacts of the liquid fraction of anaerobic digestate on biocoenosis and its impact on LLTP operational expenses. The co-treatment of landfill leachate and liquid fraction of anaerobic digestate was compared to conventional leachate treatment in an industr... [more]

Residue catalytic hydrogenation was carried out in a two-stage downflow fixed-bed reactor system, with a HDM catalyst in the first stage and HDS catalyst in the second one, to mimic the industrial operation. The experiments were run at five sets of temperatures (395 °C (first reactor)/405 °C (second reactor), 400 °C/410 °C, 405 °C/415 °C, 410 °C/420 °C, and 420 °C/430 °C). It was found that the initial stage deactivation was mainly caused by the rapid deposition of coke. Gradually, the deposition of metal sulfides leads to a slow deactivation in the middle stage of operation. A deactivation model that considers the catalyst activity as a function of TOS was proposed and applied to the hydrotreating reaction. The deactivation parameters of HDCCR, HDS, HDNi, and HDV in the two reactors were obtained by fitting the experimental data at the outlet of the two reactors. According to the deactivation curves of catalysts, it is proposed that the deactivation of HDM catalyst is faster than that... [more]

Enterprises looking to be competitive are constantly looking for a continuous increase in productivity, quality, and level of services. With the development of the industry 4.0 concept, manufacturers are more confident about the new advantages of automation and systems integration. Lean management is a well-developed and empirically proven managerial strategy. Combining lean and industry 4.0 practices seems to be a necessary evolutionary step to further raise the level of operational excellence. This study applied the main path analysis method to explore the development trend of lean management in the academic field. First, this study adopted the Scopus database to collect relevant papers, then analyzed their overall development trajectory by using Main Path 437 software, and used the g-index and h-index to identify more influential journals. Next, this study clustered the papers with similar topics into several groups, and then used Wordle software to present the keywords of each grou... [more]

The detection of the formation of pore pressure while drilling is of great importance to ensure safe drilling operations. At present, the dc-exponent concept is mainly used to detect pore pressure while drilling. The dc-exponent concept is based on the theory of shale compaction, which is limited when used in carbonate rocks. A mechanical specific energy (MSE)-based method is proposed to detect pore pressure in deep, complex intervals. The method is based on the theory that the energy consumed by the bit to break and remove a unit volume of rock can reflect the effective stress and pore pressure of the rock in situ. In this paper, a torque and weight on bit (WOB) transfer model is proposed for estimating the downhole torque and WOB using drill string mechanics. Meanwhile, the rotary speed and torque of the positive displacement motors under compound drilling are considered, and the model of total MSE under compound drilling is modified. The MSE-based method was used to estimate the por... [more]

Fast computation of the elastic deformation integrals of dry contact is accomplished using multigrid techniques. The method is called multi-level multi-integration, which enables the efficient numerical solution of contact pressure for large dry-contact problems. The computing effort can be reduced to O (NlogN) operations, compared to that of classical solution methods, O (N2). The fast integration technique can be straightforwardly applied to computing sub-surface stresses. As an example, the pressure and stress distribution of the contact of wire rope and friction lining, a large calculation due to the wire rope’s complicated construction, were fast solved. Subsequently, the friction lining’s transient temperature, when the wire rope was sliding, was solved using multigrid techniques.