A novel linear permanent magnet vernier generator (LPMVG) for small-power off-grid wave power generation systems is proposed in this paper. Firstly, in order to reduce the cogging force and the inherent edge effect of the linear generator, a staggered tooth modular structure is proposed. Secondly, in order to improve the output power and efficiency of the LPMVG and reduce the fluctuation coefficient of electromagnetic force, the relationship between the parameters of the generator is studied, and a method combining multi-objective optimization and single parameter scanning based on the response surface model and particle swarm optimization algorithm is proposed to obtain the optimal structural parameters of the generator. Thirdly, the output power and efficiency of the optimized generator are calculated and analyzed based on the two-dimensional finite element method, and the effectiveness of the multi-objective optimization design method based on the response surface model and particle... [more]

Off-grid applications based on intermittent solar power benefit greatly from hybrid energy storage systems consisting of a battery short-term and a hydrogen long-term storage path. An intelligent energy management is required to balance short-, intermediate- and long-term fluctuations in electricity demand and supply, while maximizing system efficiency and minimizing component stress. An energy management was developed that combines the benefits of an expert-knowledge based fuzzy logic approach with a metaheuristic particle swarm optimization. Unlike in most existing work, interpretability of the optimized fuzzy logic controller is maintained, allowing the expert to evaluate and adjust it if deemed necessary. The energy management was tested with 65 1-year household load datasets. It was shown that the expert tuned controller is more robust to changes in load pattern then the optimized controller. However, simple readjustments restore robustness, while largely retaining the benefits ac... [more]

The optimal siting and sizing of battery energy storage system (BESS) is proposed in this study to improve the performance of the seventh feeder at Nakhon Phanom substation, which is a distribution network with the connected photovoltaic (PV) in Thailand. The considered objective function aims to improve the distribution network performance by minimizing costs incurred in the distribution network within a day, comprising of voltage regulation cost, real power loss cost, and peak demand cost. Particle swarm optimization (PSO) is applied to solve the optimization problem. It is found that the optimal siting and sizing of the BESS installation could improve the performance of the distribution network in terms of cost minimization, voltage profile, real power loss, and peak demand. The results are investigated from three cases where case 1 is without PV and BESS installation, case 2 is with only PV installation, and case 3 is with PV and BESS installations. The comparison results show that... [more]

Energy efficiency and data security of smart grids are one of the major concerns in the context of implementing modern approaches in smart cities. For the intelligent management of energy systems, wireless sensor networks and advanced metering infrastructures have played an essential role in the transformation of traditional cities into smart communities. In this paper, a smart city energy model is proposed in which prosumer communities were built by interconnecting energy self-sufficient households to generate, consume and share clean energy on a decentralized trading platform by integrating blockchain technology with a smart microgrid. The efficiency and stability of the grid network were improved by using several wireless sensor nodes that manage a massive amount of data in the network. However, long communication distances between sensor nodes and the base station can greatly consume the energy of sensors and decrease the network lifespan. Therefore, bio-inspired algorithm approach... [more]

The rapid development and growth of battery storage have heightened an interest in the co-location of battery energy storage systems (BESS) with renewable energy projects which enables the stacking of multiple revenue streams while reducing connection charges of BESS. To help wind energy industries better understand the coordinated operation of BESS and wind farms and its associated profits, this paper develops a simulation model to implement a number of coordination strategies where the BESS supplies enhanced frequency response (EFR) service and enables the time shift of wind generation based on the UK perspective. The proposed model also simulates the degradation of Lithium-Ion battery and incorporates a state of charge (SOC) dependent limit on the charge rate derived from a constant current-constant voltage charging profile. In addition, a particle swarm optimisation-based battery sizing algorithm is developed here on the basis of the simulation model to determine the optimal size o... [more]

Power quality disturbance (PQD) is an important issue in electrical distribution systems that needs to be detected promptly and identified to prevent the degradation of system reliability. This work proposes a PQD classification using a novel algorithm, comprised of the artificial bee colony (ABC) and the particle swarm optimization (PSO) algorithms, called “adaptive ABC-PSO” as the feature selection algorithm. The proposed adaptive technique is applied to a combination of ABC and PSO algorithms, and then used as the feature selection algorithm. A discrete wavelet transform is used as the feature extraction method, and a probabilistic neural network is used as the classifier. We found that the highest classification accuracy (99.31%) could be achieved through nine optimally selected features out of all 72 extracted features. Moreover, the proposed PQD classification system demonstrated high performance in a noisy environment, as well as the real distribution system. When comparing the... [more]

The recent revolution in electric mobility is both crucial and promising in the coordinated effort to reduce global emissions and tackle climate change. However, mass electrification brings up new technical problems that need to be solved. The increasing penetration rates of electric vehicles will add an unprecedented energy load to existing power grids. The stability and the quality of power systems, especially on a local distribution level, will be compromised by multiple vehicles that are simultaneously connected to the grid. In this paper, the authors propose a choice-based pricing algorithm to indirectly control the charging and V2G activities of electric vehicles in non-residential facilities. Two metaheuristic approaches were applied to solve the optimization problem, and a comparative analysis was performed to evaluate their performance. The proposed algorithm would result in a significant revenue increase for the parking operator, and at the same time, it could alleviate the o... [more]

A competent methodology based on the active power loss reduction for optimal placement and sizing of distributed generators (DGs) in an active distribution network (ADN) with several soft open points (SOPs) is proposed. A series of SOP combinations are explored to generate different network structures and they are utilized in the optimization framework to identify the possible solutions with minimum power loss under normal network conditions. Furthermore, a generalized methodology to optimize the size and the location of a predefined number of DGs with a predefined number of SOPs is presented. A case study on the modified IEEE 33 bus system with three DGs and five SOPs was conducted and hence the overall network power loss and the voltage improvement were examined. The findings reveal that the system loss of the passive network without SOPs and DGs is reduced by 79.5% using three DGs and five SOPs. In addition, this research work introduces a framework using the DG size and the impedan... [more]

Real-time state estimation using a digital twin can overcome the lack of in-field measurements inside an electric feeder to optimize grid services provided by distributed energy resources (DERs). Optimal reactive power control of DERs can be used to mitigate distribution system voltage violations caused by increased penetrations of photovoltaic (PV) systems. In this work, a new technology called the Programmable Distribution Resource Open Management Optimization System (ProDROMOS) issued optimized DER reactive power setpoints based-on results from a particle swarm optimization (PSO) algorithm wrapped around OpenDSS time-series feeder simulations. This paper demonstrates the use of the ProDROMOS in a RT simulated environment using a power hardware-in-the-loop PV inverter and in a field demonstration, using a 678 kW PV system in Grafton (MA, USA). The primary contribution of the work is demonstrating a RT digital twin effectively provides state estimation pseudo-measurements that can be... [more]

During the day, photovoltaic (PV) systems are exposed to different sunlight conditions in addition to partial shading (PS). Accordingly, maximum power point tracking (MPPT) techniques have become essential for PV systems to secure harvesting the maximum possible power from the PV modules. In this paper, optimized control is performed through the application of relatively newly developed optimization algorithms to PV systems under Partial Shading (PS) conditions. The initial value of the duty cycle of the boost converter is optimized for maximizing the amount of power extracted from the PV arrays. The emperor penguin optimizer (EPO) is proposed not only to optimize the initial setting of duty cycle but to tune the gains of controllers used for the boost converter and the grid-connected inverter of the PV system. In addition, the performance of the proposed system based on the EPO algorithm is compared with another newly developed optimization technique based on the cuttlefish algorithm... [more]

Wind power has significant randomness. Probabilistic prediction of wind power is necessary to solve the problem of safe and stable power grid dispatching with the integration of large-scale wind power. Therefore, this paper proposes a novel nonparametric probabilistic prediction model for wind power based on extreme learning machine-quantile regression (ELM-QR). Firstly, the ELM-QR models of multiple quantiles are established, and then the new comprehensive index (NCI) is optimized by particle swarm optimization (PSO) to obtain the weighting coefficients corresponding to the lower and upper bounds of the prediction intervals. The final prediction interval is obtained by integrating the outputs of ELM-QR models and the weighting coefficients. Finally, case studies are carried out with the real wind farm operation data, simulation results show that the proposed algorithm can obtain narrower prediction intervals while ensuring high reliability. Through sensitivity analysis and comparison... [more]

This paper aims to develop an online diagnostic mechanism, doubling as a maximum power point tracking scheme, for a photovoltaic (PV) module array. In case of malfunction or shadow event occurring to a PV module, the presented diagnostic mechanism is enabled, automatically and immediately, to reconfigure a PV module array for maximum output power operation under arbitrary working conditions. Meanwhile, the malfunctioning or shaded PV module can be located instantly by this diagnostic mechanism according to the array configuration, and a PV module replacement process is made more efficient than ever before for the maintenance crew. In this manner, the intended maximum output power operation can be resumed as soon as possible in consideration of a minimum business loss. Using a particle swarm optimization (PSO)-based algorithm, the PV module array is reconfigured by means of switch manipulations between modules, such that a load is supplied with the maximum amount of output power. For co... [more]

This paper examines the solution to the problem of turbine arrangement in offshore wind farms. The two main objectives of offshore wind farm planning are to minimize wake loss and maximize annual energy production (AEP). There is more wind with less turbulence offshore compared with an onshore case, which drives the development of the offshore wind farm worldwide. South Korea’s offshore wind farms, which are deep in water and cannot be installed far off the coast, are affected by land complex terrain. Thus, domestic offshore wind farms should consider the separation distance from the coastline as a major variable depending on the topography and marine environmental characteristics. As a case study, a 60 MW offshore wind farm was optimized for the coast of the Busan Metropolitan City. For the analysis of wind conditions in the candidate site, wind conditions data from the meteorological tower and Ganjeolgot AWS at Gori offshore were used from 2001 to 2018. The optimization procedure is... [more]

The common approach to model occupants behaviors in buildings is deterministic and consists of assumptions based on predefined fixed schedules or rules. In contrast with the deterministic models, stochastic and agent based (AB) models are the most powerful and suitable methods for modeling complex systems as the human behavior. In this paper, a co-simulation architecture is proposed with the aim of modeling the occupant behavior in buildings by a stochastic-AB approach and implementing an intelligent Building Energy Management System (BEMS). In particular, optimized control logics are designed for smart passive cooling by controlling natural ventilation and solar shading systems to guarantee the thermal comfort conditions and maintain energy performance. Moreover, the effects of occupant actions on indoor thermal comfort are also taken into account. This study shows how the integration of automation systems and passive techniques increases the potentialities of passive cooling in build... [more]

The increasing deployment of wind power is reducing inertia in power systems. High-voltage direct current (HVDC) technology can help to improve the stability of AC areas in which a frequency response is required. Moreover, multi-terminal DC (MTDC) networks can be optimized to distribute active power to several AC areas by droop control setting schemes that adjust converter control parameters. To this end, in this paper, particle swarm optimization (PSO) is used to improve the primary frequency response in AC areas considering several grid limitations and constraints. The frequency control uses an optimization process that minimizes the frequency nadir and the settling time in the primary frequency response. Secondly, another layer is proposed for the redistribution of active power among several AC areas, if required, without reserving wind power capacity. This method takes advantage of the MTDC topology and considers the grid code limitations at the same time. Two scenarios are defined... [more]

In today’s world, distributed generation (DG) is an outstanding solution to tackle the challenges in power grids such as the power loss of the system that is intensified by the exponential increase in demand for electricity. Numerous optimization algorithms have been used by several researchers to establish the optimal placement and sizing of DGs to alleviate this power loss of the system. However, in terms of the reduction of active power loss, the performance of these algorithms is weaker. Furthermore, the premature convergence, the precision of the output, and the complexity are a few major drawbacks of these optimization techniques. Thus, this paper proposes the multileader particle swarm optimization (MLPSO) for the determination of the optimal locations and sizes of DGs with the objective of active power loss minimization while surmounting the drawbacks in previous algorithms. A comprehensive performance analysis is carried out utilizing the suggested approach on the standard IEE... [more]

To improve frequency nadir following a disturbance and avoid under-frequency load shedding, two types of flexible kinetic energy release controllers for the doubly fed induction generator (DFIG) are proposed. The basic idea is to release only a small amount of kinetic energy stored at the DFIG in the initial transient period (1−3 s after the disturbance). When the frequency dip exceeds a preset threshold, the amount of kinetic energy released is increased to improve the frequency nadir. To achieve the goal of flexible kinetic energy release, a deactivation function based integral controller is first presented. To further improve the dynamic frequency response under parameter uncertainties and external disturbances, a second flexible kinetic energy release controller is designed using a proportional-integral controller, with the gains being adapted in real-time with the particle swarm optimization algorithm. Based on the MATLAB/SIMULINK simulation results for a local power system, it is... [more]

During the last decade, the technologies related to electric vehicles (EVs) have captured both scientific and industrial interest. Specifically, the subject of the smart charging of EVs has gained significant attention, as it facilitates the managed charging of EVs to reduce disturbances to the power grid. Despite the presence of an extended literature on the topic, the implementation of a framework that allows flexibility in the definition of the decision-making objectives, along with user-defined criteria is still a challenge. Towards addressing this challenge, a framework for the smart charging of EVs is presented in this paper. The framework consists of a heuristic algorithm that facilitates the charge scheduling within a charging station (CS), and the analytic hierarchy process (AHP) to support the driver of the EV selecting the most appropriate charging station based on their needs of transportation and personal preferences. The communications are facilitated by the Open Platform... [more]

Generating electricity from enormous energy contained in oceans is an important means to develop and utilize marine sustainable energy. An offshore marine current generator set (MCGS) is a system that runs in seas to produce electricity from tremendous energy in tidal streams. MCGSs operate in oceanic environments with high humidity, saline-alkali water, and impacts of marine organisms and waves, and consequently malfunctions can happen along with the need for expensive inspection and maintenance. In order to achieve effective fault diagnosis of MCGSs in events of failure, this paper focuses on fault detection and diagnosis (FDD) of MCGSs based on five-phase permanent magnet synchronous generators (FP-PMSGs) with the third harmonic windings (THWs). Firstly, mathematical models were built for a hydraulic turbine and the FP-PMSG with THWs; then, a fault detection method based on empirical mode decomposition (EMD) and Hilbert transform (HT) was studied to detect different open-circuit fau... [more]

Thermal energy is an important input of furniture components production. A thermal energy production system includes complex, non-linear, and changing combustion processes. The main focus of this article is the maximization of thermal energy production considering the inbuilt complexity of the thermal energy production system in a factory producing furniture components. To achieve this target, a data-driven prediction and optimization model to analyze and improve the performance of a thermal energy production system is implemented. The prediction models are constructed with daily data by using supervised machine learning algorithms. Importance analysis is also applied to select a subset of variables for the prediction models. The modeling accuracy of prediction algorithms is measured with statistical indicators. The most accurate prediction result was obtained using an artificial neural network model for thermal energy production. The integrated prediction and optimization model is des... [more]

This paper presents a phase arrangement procedure for distribution transformers to improve system unbalance and voltage profile of distribution systems, while considering the location and uncertainties of the wind turbine (WT) and photovoltaics (PV). Based on historical data, the Monte Carlo method is used to calculate the power generation value-at-risk (VAR) of WTs/PVs installed under a given level of confidence. The main target of this paper is to reduce the line loss and unbalance factor during 24-hour intervals. Assessing the various confidence levels of risk, a feasible particle swarm optimization (FPSO) is proposed to solve the optimal location of WTs/PVs installed and transformer load arrangement. A three-phase power flow with equivalent current injection (ECI) is analyzed to demonstrate the operating efficiency of the FPSO in a Taipower feeder. Simulation results will support the planner in the proper location of WTs/PVs installed to reduce system losses and maintain the voltag... [more]

An integrated electrical and thermal residential renewable energy system consisting of solar thermal collectors, gas boiler, fuel cell combined heat and power, a photovoltaic system with battery, inverter, and thermal storage for a single-family house of Sonnenhaus standard is investigated with a model predictive controller (MPC). The main focus of this article is to define a multi-objective mathematical function, develop a coupled simulation framework for the nonlinear time-varying deterministic discrete-time problem of the energy system using TRNSYS and MATLAB. With the developed methodology, a sensitivity analysis of maximum optimization time, swarm (or population or mesh) size of a typical spring day and a typical summer day assuming a 100% accurate weather and load forecast with three different algorithms: particle swarm optimization (PSO), genetic algorithm (GA) and global pattern search (GPS) are analyzed. Finally, the obtained results are compared with a status quo controller.... [more]

The use of fossil resources for electricity production is one of the primary reasons for increasing greenhouse emissions and is a non-renewable resource. Therefore, the electricity generation by wind and solar resources have had greater applicability in recent years. Hybrid Renewable Energy Systems (HRES) integrates renewable sources and storage systems, increasing the reliability of generators. For the sizing of HRES, Artificial Intelligence (AI) methods such as Genetic Algorithms (GA) and Particle Swarm Optimization (PSO) stand out. This article presents the sizing of an HRES for the Colombian context, taking into account the energy consumption by three typical demands, four types of wind turbines, three types of solar panels, and a storage system for the system configuration. Two optimization approaches were set-up with both optimization strategies (i.e., GA and PSO). The first one implies the minimization of the Loss Power Supply Probability (LPSP). In contrast, the second one conc... [more]

This article presents the Reliability Assessment (RA) of renewable energy interfaced Electrical Distribution System (EDS) considering the electrical loss minimization (ELM). ELM aims at minimizing the detrimental effect of real power and reactive power losses in the EDS. Some techniques, including integration of Renewable Energy Source (RES), network reconfiguration, and expansion planning, have been suggested in the literature for achieving ELM. The optimal RES integration (also referred to as Distributed Generation (DG)) is one of the globally accepted techniques to achieve minimization of electrical losses. Therefore, first, the locations to accommodate these DGs are obtained by implementing two indexes, namely Index-1 for single DG and Index-2 for multiple DGs. Second, a Constriction Factor-based Particle Swarm Optimization (CF-PSO) technique is applied to obtain an optimal sizing(s) of the DGs for achieving the ELM. Third, the RA of the EDS is performed using the optimal location(... [more]

The accurate determination and dynamic adjustment of key control parameters are challenges for equivalent consumption minimization strategy (ECMS) to be implemented in real-time control of hybrid electric vehicles. An adaptive real-time ECMS is proposed for hybrid heavy-duty truck in this paper. Three efforts have been made in this study. First, six kinds of typical driving cycle for hybrid heavy-duty truck are obtained by hierarchical clustering algorithm, and a driving condition recognition (DCR) algorithm based on a neural network is put forward. Second, particle swarm optimization (PSO) is applied to optimize three key parameters of ECMS under a specified driving cycle, including equivalent factor, scale factor of penalty function, and vehicle speed threshold for engine start-up. Finally, combining all the above two efforts, a novel adaptive ECMS based on DCR and key parameter optimization of ECMS by PSO is presented and validated through numerical simulation. The simulation result... [more]