Clay minerals are an important part of the mud shale reservoir, and their type of content has a great impact on the hydration of the formation. The hydration of clay minerals causes a decrease in drilling fluid performance, an increase in pore pressure, and a decrease in rock strength, leading to wellbore wall collapse. Therefore, it is important to study the influence of clay mineral hydration on well-wall stability. In this paper, we analyze the hydration process of clay minerals qualitatively and quantitatively by simulating the mineral clay fraction and the effect of the change in cations on their hydration and clarify the difference in the hydration of different clay minerals. The results show the following: (1) montmorillonite has the most obvious hydration and swelling effect, while the hydration of illite is mainly based on hydration and dispersion, which easily produce exfoliations and fall off in the stratum; kaolinite has poor hydration performance, while chlorite shows cert... [more]

The magnitude of the impact of the pandemic on key variables, such as electricity demand, mobility of people and number of COVID-19 hospitalization cases, has been unprecedented. Existing economic models have not estimated the impact of sucokh events. This paper fills this gap, investigating the nexus among electricity demand elasticity, shifting behaviors of mobility and COVID-19 contagion with econometric estimation techniques. Firstly, using the single bids to purchase recorded in the Italian day-ahead wholesale electricity market in 2020, we estimate hourly electricity demand and price elasticity directly from short-run consumer behavior. Then, we analyze the effects of the main aspects of the pandemic, the health situation and the mobility contraction at the national level, on the estimated price elasticities. The period of heavy lockdown between 10 March and 3 June recorded a reduction in the price elasticity of electricity demand. However, when the pandemic broke out again at th... [more]

In this study, the influence of slot opening on the leakage reactance, power factors, winding current, and air gap flux density, as well as other parameters of the surface-mounted permanent magnet synchronous motor driven by an inverter is analyzed using the two-dimensional time-step finite element method. Thus, the law of permanent magnet power loss caused by slot opening under PWM qa obtained. The results show that the leakage reactance of the motor increased when the slot opening decreased from 7 mm to 2 mm. Then, the armature ripple current caused by the inverter was found to be suppressed well, and the high harmonic current was filtered well. This reduced the amplitude of the high-order harmonic of the air gap flux density, and the permanent magnet power loss was reduced by nearly 75%. Finally, two prototypes with different slot openings were tested for permanent magnet temperature rise, which verified the analysis method and calculation results proven in this paper.

The oil and gas resources stored in deep strata are an important replacement field of the petroleum industry. Accelerating the exploration and development of deep oil and gas is of great significance to the security of energy strategy. Drilling is the primary link and necessary means of deep oil and gas exploration and development. Slow drilling speed is one of the key problems restricting the exploration and development of deep oil and gas. The research and development of down-hole equipment with an increasing ROP provides a technical means for increasing the ROP. However, the energy of existing down-hole equipment with an increasing ROP comes from the drilling circulation medium, and the ROP increase effect of such equipment is relatively obvious in shallow and middle formations. However, with the increase in well depth, energy in the circulation medium increasingly struggles to reach deeper formations, and the ROP increase effect is not good at the later stage of drilling. In the dr... [more]

Converting CO2 into fuels via solar-driven thermochemical cycles of metal oxides is promising to address global climate change and energy crisis challenges simultaneously. However, it suffers from low energy conversion efficiency (ηen) due to high sensible heat losses when swinging between reduction and oxidation cycles, and a single product of fuels can hardly meet multiple kinds of energy demands. Here, we propose an alternative way to upsurge energy conversion efficiency by integrating solar thermochemical CO2 splitting with a supercritical CO2 thermodynamic cycle. When gas phase heat recovery (εgg) is equal to 0.9, the highest energy conversion efficiency of 20.4% is obtained at the optimal cycle high pressure of 260 bar. In stark contrast, the highest energy conversion efficiency is only 9.8% for conventional solar thermochemical CO2 splitting without including a supercritical CO2 cycle. The superior performance is attributed to efficient harvesting of waste heat and synergy of CO... [more]

Energy efficiency is becoming one of the key research topics in the energy field and has, therefore, attracted extensive attention in recent research [...]

High-voltage fuses are found in most electrical installations, where they are used for overcurrent protection and are the pieces of equipment providing the highest degree of protection for the lowest initial cost. This article focuses on the behavior of high-voltage fuses containing a fuse element entirely made of aluminum. We made high-power linear electrical circuits for experiments on these fuses under the most severe operating conditions. The article presents the construction details of the fuse element and its features, as well as various arc extinguishing media. The heating behavior and time−current characteristics were studied in comparison with fuses made of copper. We obtained the maximum instantaneous value of the current reached during interruption for a 24 kV, 50 kA, 50 A fuse, as well as the value of the minimum breaking current.

The seismic sensors used for automatic seismic trip systems (ASTS) of nuclear power plants (NPPs) are mainly arranged on the raft foundation of reactor buildings; however, the arrangement principle of seismic sensors is not clear. In order to analyze the seismic response sensitivity of the raft foundation of reactor building in NPPs, this paper carried out the seismic response sensitivity research at seven positions on the raft foundation of a reactor building under three site conditions, with two sets of time histories as input. The results show that (1) the peak acceleration of the outer ring point of the raft foundation was the largest, and the peak acceleration of the center point was the smallest; (2) the peak value of the floor response spectrum at the outer ring point of the raft foundation was the largest, and the peak value at the center point was the smallest. In an earthquake, the outer ring point of the raft foundation of the reactor building was the most sensitive. It was... [more]

In the context of power quality problems, the voltage imbalance index is relevant, given its harmful impacts on the networks and loads. Thus, reliable and viable methodologies for practical use are necessary to determine agents’ contributions. This article presents a noninvasive method for sharing responsibility for imbalances based on the principle of superposing the individual voltage imbalance produced by the parties. A procedure based on the Complex Independent Component Analysis (CICA) technique is proposed to meet the parameters required by the superposition method. Based on the measurements of voltages and currents carried out on the point of common coupling (PCC), the negative sequence impedances are determined using the CICA method under the terms needed by the superposition principle. The methodology’s effectiveness is evaluated through performance comparisons carried out over the process, in light of the response from the methods for sharing responsibilities currently publis... [more]

The aim of this analysis is to identify the possibility of treating eco-innovation in micro and small enterprises as a factor influencing the energy efficiency of the economy. In order to obtain an answer to such a research question, quantitative research was carried out among Polish enterprises from the SME sector (N = 400). Accordingly, the CATI technique was applied. The selection of enterprises was random and took place in the non-returnable drawing process. The criterion for selecting the sample was the size of enterprises, but in order to ensure the possibility of drawing conclusions based on a sufficiently large research sample, its structure (300 micro and 100 small enterprises) assumed the study of small enterprises in a proportion greater than their actual share in the population of enterprises. As a result of this research, the existence of a relationship between the improvement of the company’s competitive position and its activity in the field of eco-innovation implementat... [more]

Since the COVID-19 outbreak, special attention has been paid to proper ventilation and building management systems. The indoor air CO2 concentration level is still used as an effective indicator to evaluate indoor air quality. Many different sensors have appeared on the market in the last two years. However, calibration procedures and guidance on proper installation have not been well described by manufacturers. The research method is based on a review of technical parameters. The practical measurements of CO2 concentration were taken using different sensors. For these purposes three different premises were selected. It was found that CO2 measurement failure happened in residential buildings without mechanical ventilation. Meanwhile, in well ventilated buildings all sensors have shown similar results and the difference between sensors located in different zones was minimal.

The aim of this paper is to analyze energy pathways for a fossil fuel rich developing country towards an energy transition considering national and international oil availability using Ecuador as a reference. An integrated assessment model has been developed to simulate energy transition scenarios considering constraints on oil availability at the national and global level. Results show that if current trends in energy demand and supply persist, energy scarcity would start around 2040 due to depletion of national oil reserves and restricted access to foreign oil. This would trigger a degrowth in economic activity in sectors with high dependency on petroleum products. Scenarios with conservative efforts might partially revert the increasing use of fossil fuels supported by policies for energy efficiency and substitution of liquid fuels with electricity mainly from renewables. However, energy shortages would still be foreseeable as well as a decay of the economy. Under a maximum efforts... [more]

The volatility of oil price as a key energy resource for modern economies has a significant impact on the macroeconomic situation. In addition to affecting aggregated production, consumption, employment and inflation, oil shocks can affect the economy in a more nuanced way. One consequence of the turmoil in the oil market may be a shift in the employment structure between the tradable and non-tradable sectors, which we investigate in this paper. The aim of this study is to test how oil price volatility affects the structure of employment in Central and Eastern European countries. Our main hypothesis is that oil price volatility causes a temporal employment reallocation between tradable and non-tradable sectors. To verify this assumption, we created Interacted Panel VAR (IPVAR), which showed that the shocks of oil price volatility affect the employment structure and this impact is conditioned by the level of dependence on energy imports and the exchange rate regime. The constructed impu... [more]

The generation and emission characteristics of fine particulates (PM2.5) from three 300 MW power plant circulating fluidized bed boilers were investigated. One boiler had an external bed and used an electrostatic precipitator, the other two used an electrostatic filter precipitator and fabric filter, respectively. The particle size distribution of fine particles was performed by an electrical low-pressure impactor. PM2.5 samplers were used at the same time to collect fine particles for subsequent laboratory analysis. The results show that the number size distributions of fine particles presented one single peak, but there was no peak in mass size distributions. The mass concentrations of three CFB boilers were similar, but the number concentration of the external bed CFB boiler was much higher than that of the general CFB boiler. The minimum removal efficiencies of the precipitator appeared between 0.1~1 μm, but the locations of the minimum point were different. The morphology of fine... [more]

Determining the demand for heat power for domestic hot water preparation is necessary to perform a building energy assessment. For this, we need to predict domestic hot water consumption. Considering the number of factors influencing domestic hot water consumption, it is difficult to develop a highly accurate methodology. The aim of the study was to compare the real domestic hot water consumption and heat power for its preparation with the values calculated based on the available prediction methods in multi-family buildings. The analysis was carried out based on annual monitoring (2021 year) of domestic hot water consumption and the actual demand for heat power in eight multi-family buildings located in Grudziądz, in Central Poland. The results of these measurements were compared with the values determined based on the available methodologies for forecasting the demand for heat power and domestic hot water consumption: Sander’s, Recknagel’s, the standard method and the method according... [more]

Currently, woodchips and logging residues form the greatest share of biomass fuels used to generate heat in combined heat and power plants. They are supplied from various regions of the EU. The calorific values of the wood species used as biomass may vary significantly depending on the moisture and composition of the fuel, harvest seasonality, location, and other factors. This article presents the main resources of forest biomass and its characteristic features, as well as the calorific value of woodchips depending on the moisture content. Our research is based on the source data of forest resources from the State Forests National Forest Holding (PGLLP) in Poland. The research conducted by the main forestry enterprise in Poland covered a period of four years. The data on the harvesting of woodchips and logging residues converted into the calorific values of biomass were based on our research and a review of reference publications. Standard methods were used in the research, which inclu... [more]

This article was aimed to answer the question of whether local energy communities have a sufficient energy surplus for storage purposes, including hydrogen production. The article presents an innovative approach to current research and a discussion of the concepts of the collective prosumer and virtual prosumer that have been implemented in the legal order and further amended in the law. From this perspective, it was of utmost importance to analyze the model of functioning of an energy cluster consisting of energy consumers, energy producers, and hydrogen storage, whose goal is to maximize the obtained benefits, assuming the coopetitive nature of the relationship. The announced and clear perspective of the planned benefits will provide the cluster members a measurable basis for participation in such an energy community. However, the catalogue of benefits will be conditioned by the fulfillment of several requirements related to both the scale of covering energy demand from own sources a... [more]

Future grid refers to the next generation of the electrical grid, which will enable smart integration of conventional, renewable, and distributed power generation, energy storage, transmission and distribution, and demand management [...]

Energy transitions inherit complex processes full of surprises, unintended consequences, erroneous decisions, uncertainties, paradoxical situations, and sometimes sheer failures [...]

Accurate forecast results of medium and long-term wind power quantity can provide an important basis for power distribution plans, energy storage allocation plans and medium and long-term power generation plans after wind power integration. However, there are still some problems such as low forecast accuracy and a low degree of integration for wind power physical processes. In this study, the Multi-step Informer network is proposed to add meteorological parameters to wind power generation forecast and make network interpretable. The Multi-step Informer network uses Informer to obtain the initial training model according to the historical data of wind power generation, introduces the Informer model of wind speed and air pressure training involved in the dynamic pressure model, and compares the historical data of wind power generation to obtain model modification, so as to further improve the forecast accuracy of Multi-step Informer network. The backpropagation process of the pre-trained... [more]

The development of emerging technologies not only has recently affected current industrial production but also has generated promising manufacturing opportunities that impact significantly on social and economic factors. Exploring upcoming renovation tendencies of technologies prematurely is essential for governments, research and development institutes, and industrial companies in managing strategies to achieve dominant advantages in business competitiveness. Additionally, the prospective changes, the scientific research directions, and the focus of technologies are crucial factors in predicting promising technologies. On the other hand, Industry 4.0 revolutionizes standards and models by accompanying significant technology developments in numerous sectors, including the sector of Smart energy. Moreover, asset performance management is always a prominent topic that has attained prevalence over the last decade because numerous challenges force all industrial companies to optimize their... [more]

The properties of GaAsSbN and GaAsSb layers grown by liquid-phase epitaxy on n-GaAs substrates were investigated in a comparative plan with a view of their possible application in multi-junction solar cells. To avoid non-uniformity effects in the composition of these compounds with two or three different group-V volatile elements, the crystallization was carried out from finite melt with a thickness of 0.5 mm at low (<560 °C) temperatures. X-ray microanalysis and X-ray diffraction were used to determine the composition, lattice mismatch, and crystalline quality of the epitaxial layers. The morphology and surface roughness were examined by atomic force microscopy. Surface photovoltage (SPV) spectroscopy at room temperature was applied to study the optical absorption properties and the photocarrier transport in the samples. The long-wavelength photosensitivity of the GaAsSbN and GaAsSb layers, determined from their SPV spectra, is extended down to 1.2 eV. Although GaAsSb has a slightl... [more]

The resilience of energy systems is gaining more importance under the threat of pandemics, extreme weather, natural disasters, military conflicts, trade wars, energy supply shortages, rising energy demand, etc. [...]

The computational models of physical systems comprise parameters, independent and dependent variables [...]

In order to investigate the effect of rock surface roughness on the occurrence state of shale oil, muscovite mica was firstly characterized by performing atomic force microscopy (AFM). Two-dimensional (2D) images and the three-dimensional (3D) structure of the mica surface were obtained. Wettability of the micas was measured according to the sessile drop method using shale oil, collected from a lacustrine shale oil well drilling through the Yanchang Formation, Ordos Basin. Then, the adhesion forces between shale oil and mica surface with a different roughness were finely measured using AFM mounted with the shale oil modified probe tips. The adhesion force curves at the approaching and retract modes were obtained. The results show that the average roughness value of the mica samples was about 1 nm, while the maximum height was up to 4 nm. The contact angle between shale oil and mica ranged from 128.73° to 145.81°, and increased with increasing surface roughness, which can be described b... [more]