The paper proposes a novel approach to modeling electrified transportation systems. The proposed solution reflects the mechanical dynamics of vehicles as well as the distribution and losses of electric supply. Moreover, energy conversion losses between the mechanical and electrical subsystems and their bilateral influences are included. Such a complete model makes it possible to replicate, e.g., the impact of voltage drops on vehicle acceleration or the necessity of partial disposal of regenerative braking energy due to temporary lack of power transmission capability. The modeling methodology uses a flexible twin data-bus structure, which poses no limitation on the number of vehicles and enables modeling complex traction power supply structures. The proposed solution is suitable for various electrified transportation systems including suburban and urban systems. The modeling methodology is applicable i.a. to Matlab/Simulink, which makes it broadly available and customizable, and provid... [more]

In order to reduce greenhouse gas emissions, current and future energy systems need to be made more efficient and sustainable. This change can be accomplished by increasing the penetration of renewable energy sources and using efficient technologies in energy generation systems. One way to improve the operation of the whole energy system is through the generation and end-use sector coupling. Power-to-heat energy conversion and storage technologies, in this view, are enabling technologies that can help in balancing and improving the efficiency of both thermal and electric grids. In the present paper, a comprehensive analysis of the role of heat pumps and thermal energy storage for sector coupling is presented. The main features of the analyzed technologies are presented in the context of smart electric grid, district heating and cooling and multi-carrier energy systems, and recent findings and developments are highlighted. Finally, the technical, social, and economic challenges in the a... [more]

This paper proposes a method for synchronizing a grid inverter with the voltage of an on-board high-frequency power grid. The described synchronization method belongs to the adaptive methods, which use fuzzy logic in the process of estimating the fundamental component of the voltage. The synchronization system has been tuned to achieve the primary goal of achieving synchronization in the shortest possible time. This is to allow for the efficient energy fed from photovoltaic sources into the on-board grid at 400 Hz. The proposed method was implemented in the field programmable gate array (FPGA) based power converter controller and static and dynamic tests for harmonic, interharmonic and subharmonic voltage disturbances were performed. Dynamic tests for phase jump, frequency jump and sag of the on-board voltage were also performed. To evaluate the effectiveness of synchronization with high-frequency voltage, the grid current control system in the grid tied inverter was elaborated. Proper... [more]

With the rapid development of FSAE, the speed of racing cars has increased year by year. As the main research content of racing cars, aerodynamics has received extensive attention from foreign teams. For racing cars, the aerodynamic force on the aerodynamic device ultimately acts on the tires through the transmission of the body and the suspension. When the wheel is subjected to the vertical load generated by the aerodynamic device, the ultimate adhesion capacity of the wheel is improved. Under changing conditions, racing wheels can withstand greater lateral and tangential forces. Therefore, the effects of aerodynamics have a more significant impact on handling stability. The FSAE racing car of Jilin University was taken as the research object, and this paper combines the wind tunnel test, the numerical simulation and the dynamics simulation of the racing system. The closed-loop design process of the aerodynamics of the FSAE racing car was established, and the joint study of aerodynami... [more]

Many countries, especially China, have extensively promoted liquefied natural gas (LNG) to replace diesel in heavy-duty vehicles for to achieve sustainable transport aims, including carbon peaks and neutrality. We developed a life-cycle calculation model for environmental load differences covering vehicle and fuel cycles to comprehensively compare the LNG tractor-trailer and its diesel counterpart in China on a full suite of environmental impacts. We found that the LNG tractor-trailer consumes less aluminum but more iron and energy; emits less nitrogen oxide, sulfur oxide, nonmethane volatile organic compounds, and particulate matter but more greenhouse gases (GHG) and carbon monoxide (CO); and causes less abiotic depletion potential, acidification potential, and human toxicity potential impacts but more global warming potential (GWP) and photooxidant creation potential (POCP) impacts. Poor fuel economy was found to largely drive the higher life-cycle GHG and CO emissions and GWP and P... [more]

The motivation to improve components in electric power equipment brings new proposals from world-renowned scientists to strengthen them in operation. An essential part of every electric power equipment is its insulation system, which must have the best possible parameters. The current problem with mineral oil replacement is investigating and testing other alternative electrical insulating liquids. In this paper, we present a comparison of mineral and hydrocarbon oil (liquefied gas) in terms of conductivity and relaxation mechanisms in the complex plane of the Cole-Cole diagram and dielectric losses. We perform the comparison using the method of dielectric relaxation spectroscopy in the frequency domain at different intensities of the time-varying electric field 0.5 kV/m, 5 kV/m, and 50 kV/m. With the increasing intensity of the time-varying electric field, there is a better approximation of the Debye behavior in all captured polarization processes of the investigated oils. By comparing... [more]

The Li-S battery is exceptionally appealing as an alternative candidate beyond Li-ion battery technology due to its promising high specific energy capacity. However, several obstacles (e.g., polysulfides’ dissolution, shuttle effect, high volume expansion of cathode, etc.) remain and thus hinder the commercialization of the Li-S battery. To overcome these challenges, a fundamental study based on atomistic simulation could be very useful. In this work, a comprehensive investigation of the adsorption of electrolyte (solvent and salt) molecules, lithium sulfide, and polysulfide (Li2S with 2 ≤x≤ 8) molecules on the amorphous Al2O3 atomic layer deposition (ALD) surface was performed using first-principles density functional theory (DFT) calculations. The DFT results indicate that the amorphous Al2O3 ALD surface is selective in chemical adsorption towards lithium sulfide and polysulfide molecules compared to electrolytes. Based on this work, it suggests that the Al2O3 ALD is a promising coat... [more]

Currently, the design of floating offshore wind systems is primarily based on mid-fidelity models with empirical drag forces. The tuning of the model coefficients requires data from either experiments or high-fidelity simulations. As part of the OC6 (Offshore Code Comparison Collaboration, Continued, with Correlation, and unCertainty (OC6) is a project under the International Energy Agency Wind Task 30 framework) project, the present investigation explores the latter option. A verification and validation study of computational fluid dynamics (CFD) models of the DeepCwind semisubmersible undergoing free-decay motion is performed. Several institutions provided CFD results for validation against the OC6 experimental campaign. The objective is to evaluate whether the CFD setups of the participants can provide valid estimates of the hydrodynamic damping coefficients needed by mid-fidelity models. The linear and quadratic damping coefficients and the equivalent damping ratio are chosen as me... [more]

Heavy petroleum industries, including the Fluid Catalytic Cracking (FCC) unit, are among some of the biggest contributors to global greenhouse gas (GHG) emissions. The FCC unit’s regenerator is where these emissions originate mostly, meaning the operation of FCC regenerators has come under scrutiny in recent years due to the global mitigation efforts against climate change, affecting both current operations and the future of the FCC unit. As a result, it is more important than ever to develop models that are accurate and reliable at predicting emissions of various greenhouse gases to keep up with new reporting guidelines that will help optimise the unit for increased coke conversion and lower operating costs. Part 1 of this paper was dedicated to reviewing the riser section of the FCC unit. Part 2 reviews traditional modelling methodologies used in modelling and simulating the FCC regenerator. Hydrodynamics and kinetics of the regenerator are discussed in terms of experimental data and... [more]

The area of degraded sites in the world is constantly expanding and has been a serious environmental problem for years. Such terrains are not only polluted, but also due to erosion, devoid of plant cover and organic matter. The degradation trends can be reversed by supporting remediation/reclamation processes. One of the possibilities is the introduction of biodegradable waste/biowaste substrates into the soil. The additives can be the waste itself or preformed substrates, such composts, mineral-organic fertilizers or biochar. In EU countries average value of compost used for land restoration and landfill cover was equal 4.9%. The transformation of waste in valuable products require the fulfillment of a number of conditions (waste quality, process conditions, law, local circumstances). Application on degraded land surface bio-based waste substrates has several advantages: increase soil organic matter (SOM) and nutrient content, biodiversity and activity of microbial soil communities an... [more]

Global energy transition trends are reflected not only in oil and gas market dynamics, but also in the development of related sectors. They influence the demand for various types of metals and minerals. It is well-known that clean technologies require far more metals than their counterparts relying on fossil fuels. Nowadays, rare-earth metals (REMs) have become part and parcel of green technologies as they are widely used in wind turbine generators, motors for electric vehicles, and permanent magnet generators, and there are no materials to substitute them. Consequently, growth in demand for this group of metals can be projected in the near future. The topic discussed is particularly relevant for Russia. On the one hand, current trends associated with the global energy transition affect the country’s economy, which largely depends on hydrocarbon exports. On the other hand, Russia possesses huge REM reserves, which may take the country on a low-carbon development path. However, they are... [more]

Electrochemical impedance spectroscopy is one of the important tools for the performance analysis and diagnosis of proton exchange membrane fuel cells. The equivalent circuit model is an effective method for electrochemical impedance spectroscopy resolution. In this paper, four typical equivalent circuit models are selected to comprehensively compare and analyze the difference in the fitting results of the models for the electrochemical impedance spectroscopy under different working conditions (inlet pressure, stoichiometry, and humidity) from the perspective of the fitting accuracy, change trend of the model parameters, and the goodness of fit. The results show that the fitting accuracy of the model with the Warburg element is the best for all under each working condition. When considering the goodness of fit, the model with constant phase components is the best choice for fitting electrochemical impedance spectroscopy under different inlet pressure and air stoichiometry. However, und... [more]

Due to the growing demand for new ecological, low-emission heat sources, there is a need to develop new tools for simulating the operating parameters and costs of the implemented solutions. The article analyses the existing solutions for the simulation of heat pump operation parameters, describes the requirements for a modern building—nZEB and proposes a simulation tool based on thermodynamic parameters of the refrigerant. The script allows for deriving simple linear equations that can be used for the overall simulation of a system in which the heat pump is a key part and the efficiency of the entire system depends on its performance. The developed numerical script allows for reproducing the Linde refrigeration cycle and the parameters of its characteristic points. To calibrate the simulation, historical data obtained from the SOPSAR system were used. These data were pre-cleaned (peaks and other obvious measurement errors were removed). The obtained numerical model in combination with... [more]

Industrial processes are characterized by energy losses, such as heat streams rejected to the environment in the form of exhaust gases or effluents occurring at different temperature levels. Hence, waste heat recovery (WHR) has been a challenge for industries, as it can lead to energy savings, higher energy efficiency, and sustainability. As a consequence, WHR methods and technologies have been used extensively in the European Union (EU) (and worldwide for that matter). The current paper revisits and reviews conventional WHR technologies, their use in all types of industry, and their limitations. Special attention is given to alternative “new” technologies, which are discussed for parameters such as projected energy and cost savings. Finally, an extended review of case studies regarding applications of WHR technologies is presented. The information presented here can also be used to determine target energy performance, as well as capital and installation costs, for increasing the attra... [more]

Biochar is attracting attention as an alternative carbon/fuel source to coal in the process industry and energy sector. However, it is prone to self-heating and often leads to spontaneous ignition and thermal runaway during storage, resulting in production loss and health risks. This study investigates biochar self-heating upon its contact with O2 at low temperatures, i.e., 50−300 °C. First, kinetic parameters of O2 adsorption and CO2 release were measured in a thermogravimetric analyzer using biochar produced from a pilot-scale pyrolysis process. Then, specific heat capacity and heat of reactions were measured in a differential scanning calorimeter. Finally, a one-dimensional transient model was developed to simulate self-heating in containers and gain insight into the influences of major parameters. The model showed a good agreement with experimental measurement in a closed metal container. It was observed that char temperature slowly increased from the initial temperature due to hea... [more]

The selection of appropriate heat-resistant materials which are at the same time resistant to atmospheres rich in chlorine and its compounds is one of the most important current construction problems in steel boiler elements when using biomass fuels of agricultural origin. In the research presented here, an area was identified in the furnace of a 10 kW boiler where there was a potential risk of chlorine corrosion. This zone was determined based on numerical analysis of the combustion process; it is the zone with the highest temperatures and where the gas atmosphere conducive to the formation of chlorine corrosion centers. Subsequently, tests were carried out in the process environment of the combustion chamber of a 10 kW boiler (the fuel was barley straw) by placing samples of eight construction materials in a numerically-designated zone. These included samples of steel (coal boiler St41K, heat-resistant H25T and H24JS, and heat-resistant valve 50H21G9N4) as well as intermetallic mater... [more]

The continuous operation and the specialized conditions needed for safely delivering healthcare services make hospitals among the most expensive buildings. Several studies in different countries have investigated the potential role and contribution of macroscopic indices of hospitals in total energy requirements. In this work, we tried to investigate the energy requirements of Greek hospitals in terms of cost. We collected data from all public hospitals in Greece over a 2 year period (2018−2019) and evaluated the contribution of various factors in the total energy cost. The data revealed large variability by region and by hospital, even regarding structures of the same category and size. The analysis also showed that structural and operational data of each hospital differently influence the hospitals’ energy requirements. Using regression methods, we developed two models for calculating annual energy costs. One only contains hospital structural data (number of beds, type of hospital, n... [more]

This paper presents a method to extend the DC bus utilization on an induction motor (IM) by using a combination of Space-Vector Modulated Direct Torque Control (DTC−SVM) and conventional DTC. The scheme proposed in this paper exploits the advantages of both control methods. During the linear region, it allows for a low torque ripple and low current harmonic distortion (THD). During the overmodulation region, it allows for the fastest torque response up to the six-step operation region. In both regions, there is complete independence of the motor parameters. The paper describes a way to provide a smooth transition between the two control schemes. Non-linearities affect the stator flux angle estimation, which leads to the inability to decouple torque and flux. To overcome this problem, a novel PI-based control scheme as well as a simplification on the decoupling terms’ calculation are proposed. Simulation and experimental results are presented to verify the feasibility of the proposed me... [more]

The seal is designed to reduce leakage and improve the efficiency of gas turbine machines, and is an important technology that needs to be studied in gas turbine design. A series of seals were proposed to try to achieve this goal. However, due to the complex fluid dynamic performance of the seal-rotor system, the seal structure can obtain both the best leakage performance and best rotordynamic performance. This paper presents a detailed flow analysis of the hole diaphragm labyrinth seal (HDLS) at several whirl frequencies and several rotation speeds. The pressure drop, velocity, turbulence kinetic energy and leakage performance of the HDLS were discussed by simulations. An interesting exponential−type relationship between rotation speeds and leakage flow at different whirl frequencies was observed by curve fitting technology. A reverse flow rate was proposed to describe such an unusual phenomenon. Such a relationship can be used to further establish the leakage model of the HDLS and ot... [more]

Hydrostatic transmissions are commonly used in heavy-duty equipment for their design flexibility and superior power density. Compared to a conventional wind turbine transmission, a hydrostatic transmission (HST) is a lighter, more reliable, cheaper, continuously variable alternative for a wind turbine. In this paper, for the first time, a validated dynamical model and controlled experiment have been used to analyze the performance of a hydrostatic transmission with a fixed-displacement pump and a variable-displacement motor for community wind turbines. From the dynamics of the HST, a pressure control strategy is designed to maximize the power capture. A hardware-in-the-loop simulation is developed to experimentally validate the performance and efficiency of the HST drive train control in a 60 kW virtual wind turbine environment. The HST turbine is extensively evaluated under steady and time-varying wind on a state-of-the-art power regenerative hydrostatic dynamometer. The proposed cont... [more]

The main aim of this article was to test the authors’ proprietary method (i.e., the conversion method applied to evaluate e-banking services that support sustainable development goals in households, communities, and society). The authors’ conversion method can be applied with the aim of maintaining a balance between households, producers, and public administration services in line with the principles of sustainable development of the information society in Poland. To achieve this goal, the authors identified the differences between the results obtained using the conversion method and the results produced by other methods such as TOPSIS, Promethee II, and PROSA involving the same group of respondents. A hypothesis was made about the existence of significant differences in the results obtained as part of the studies. The research was carried out on a sample of nearly 830 ratings concerning the 27 most popular electronic banks in Poland. As part of the survey, the respondents assessed 18... [more]

Throughout the world, and especially in the European Union, numerous technologies for the thermal treatment of radioactive waste are available or being developed. These technologies can be applied to a large range of different radioactive waste streams, including non-standard types of waste that present specific waste management challenges. Thermal treatment can result in a significant reduction in volume and hazard, which are beneficial for safe storage and disposal. Thermal treatment also removes organic material that can form complexing agents and increase the mobility of radionuclides in the landfill. In the paper, basic thermal techniques are presented, and some examples of the installations are shown. Common knowledge of these methods may result in an increased public acceptance of nuclear energy in a country just introducing it, as Poland is.

This effort to make the power grid more intelligent is tightly coupled with the deployment of advanced metering infrastructure (AMI) as an integral part of the future vision of smart grid. The goal of AMI is to provide necessary information for the consumers and utilities to accurately monitor and manage energy consumption and pricing in real time. Immediate benefits are enhanced transparency and efficiency of energy usage and the improvement of customer services. Although the road map toward successful AMI deployment is clearly defined, many challenges and issues are to be solved regarding the design of AMI. In this paper, a multi-agent AMI based on the fog-computing approach is presented. Architecture follows structural decomposition of AMI functionalities encapsulated in a form of local and area-specific service components that reside at the different tiers of hierarchically organized AMI deployment. Fog computing concepts provide the framework to effectively solve the problems of c... [more]

This work aims to study the impact of nanofluids with alumina particles on pool boiling performance. Unlike most studies, which use a trial-and-error approach to improve boiling performance parameters, this study details the possible effects of nanoparticles on the effective mechanisms of boiling and heat transfer. For this purpose, biphilic surfaces (hydrophilic surfaces with superhydrophobic spots) were used, which allow the individual analysis of bubbles. Surfaces with different configurations of superhydrophobic regions were used. The thermophysical properties of fluids only vary slightly with increasing nanoparticle concentration. The evolution of the dissipated heat flux and temperature profiles for a nucleation time frame is independent of the fluid and imposed heat flux. It can be concluded that the optimal concentration of nanoparticles is 3 wt%. Using this nanoparticle concentration leads to lower surface temperature values than those obtained with water, the reference fluid.... [more]

Preheating is often required to prevent hydrate formation during the pressure reduction process in a natural gas distribution network’s pressure reduction station. This paper examines an energy recovery method to avoid the cost and energy consumption of this preheating. The primary aim is to assess the techno-economic feasibility of an energy recovery system based on the Ranque−Hilsch vortex tube coupled to a heat exchanger for large-scale application to the gas grid. To this end, a techno-economic model of the entire energy recovery system was included in an optimisation procedure. The resulting design minimises the payback period (PP) when the system is applied to the pressure reduction stations belonging to a particular gas grid. The pressure reduction stations always operate at an outlet pressure above atmospheric pressure. However, available performance models for the Ranque−Hilsch vortex tube do not permit prediction at backpressure operation. Therefore, a novel empirical model o... [more]