The aim of this paper was to evaluate the characteristics and the energy potential for the methane production of fine screenings collected from the primary stage of a municipal wastewater treatment plant, and assess the impact on the properties and the oxygen demand of the aqueous effluents downstream from the sieves. Commercial filter bags with sieve openings of 3000, 1250, 1000, and 300 μm were used for the collection of screenings following a measurement of their biochemical methane potential. It was revealed that solid fractions from the sieves with a large size presented a high net methane production capacity exceeding 900 mL/g VS, but the gas production rate was rather slow, requiring a long time to reach the final value. However, cumulative solid fractions containing particles with a size larger than 300 μm had a lower net methane production, about 700 mL/g VS, but with a faster rate, resulting in almost 80% of the total volume released in 30 days. Aqueous samples downstream fro... [more]

The built environment sector is responsible for a significant proportion of the final global energy consumption [...]

In the research carried out by the authors, an approach to the assessment of the project environment of technologically integrated “European Green Deal” projects using corn waste was developed, which takes into account the changing project environment, which determines the risk of the specific cost of disposal of corn waste. On the basis of the predicted approach and the established trends of changes in the specific volume of corn food products from its yield, as well as the specific cost of disposal of corn waste from its specific volume under the condition of maintaining the balance of organic carbon in the fields, a computer program in the Python 3.9 language was developed. The program makes it possible to speed up calculations and perform a quantitative assessment of the state of the project environment in certain regions of the implementation of projects of the “European Green Deal” (TIP of the EGD) using corn waste. An approach to assessing the state of the project environment of... [more]

As the impacts of environmental change become more severe, reliable and sustainable power generation and efficient aerodynamic power collection of onshore and offshore wind turbine systems present some of the associated key issues to address. Therefore, this review article aims to present current advances and challenges in the aerodynamic power extraction of wind turbines, associated supporting technologies in pitch, yaw, and torque control systems, and their advantages and implications in the renewable energy industry under environmental challenges. To do this, first, mathematical modeling of the environmental characteristics of the wind turbine system is presented. Next, the latest technological advances consider the environmental challenges presented in the literature, and merits and drawbacks are discussed. In addition, pioneering research works and state-of-the-art methodologies are categorized and evaluated according to pitch, yaw, and torque control objectives. Finally, simulati... [more]

In the transition towards a sustainable world with a “green horizon” (something that is also of great importance to the policy of energy self-sufficiency in housing and self-consumption), geothermal energy is seen as quite a feasible alternative for single-family homes. This article focuses on a comparison between the environmental impact and life cycle analysis of three alternatives and provides a base case for the replacement of a conventional type of boiler with a geothermal one for a typical house located in a Mediterranean climate. The first alternative (A) consists of a horizontal catchment system through a field of geothermal probes. The second alternative (B) is a shallow water catchment system, open type, with the return of water to a nearby river. The third option studied (C) is also a shallow water catchment system but with the water, return injected into a well downstream to the underground water flow. The study shows that alternatives A and B have the least environmental i... [more]

A direct absorption parabolic trough solar collector (DAPTC) integrated with porous foam as a volumetric absorber has the potential to be applied as an energy conversion integrant of future renewable energy systems. The present study comprehensively analyzes a DAPTC in terms of exergy, economic, and environmental analysis for different porous configuration inserts in the absorber tube. Ten different arrangements of porous foam are examined at several HTF flow rates (40−120 L/h) and inlet temperatures (20−40 °C). The exergy efficiency, entropy generation, Bejan number, and pumping power are investigated for all cases. Obtained results indicate that fully filling the absorber tube with porous foam leads to a maximum exergy efficiency of 20.4% at the lowest inlet temperature (20 °C) and highest flow rate (120 L/h). However, the Bejan number reaches its minimum value due to the highest pumping power in this case. Consequently, all mentioned performance parameters should be considered simul... [more]

This study presents a simple indoor air quality diagnosis program for school office spaces, which are occupied for long durations by teachers, and indoor sports facilities, whose utilization has been on the rise in response to high concentrations of pollutants in outdoor air. The proposed program was made with Visual Basic for Applications (VBA) and Microsoft Excel. This program requires inputs which can be easily determined or measured even by nonexperts and can check the current status of indoor air quality such as CO2 and PM2.5 concentrations and predict the effect if changes are made. In addition, it is possible to diagnose indoor air quality before and after class and compare it with the initial plan so that if it exceeds the indoor air quality maintenance standard range, it can be improved by using a ventilation system and an air purifier. The development of the program was divided into four stages. First, prior research on the influencing factors was investigated. Second, influe... [more]

The main sources of environmental pollution with heavy (ecotoxic) metals include industry, including utility and municipal power engineering, but also waste incineration plants. Fuel shortages and their constantly growing prices raise concerns that energy will be commonly obtained from waste outside of installations intended for this purpose (i.e., outside waste incineration plants). The greatest concern stems from the risk of burning waste in low-power boilers—domestic boilers. Waste incineration plants and utility power plants are equipped with flue gas cleaning installations (FGD), but low-power boilers are not. The exhaust gases are directly introduced into the atmosphere, which results in the introduction into the air of, inter alia, toxic heavy metals. Therefore, it is necessary to conduct activities aimed at retaining ecotoxic metals in the solid−slag residue. The paper presents the results of laboratory tests of the emission capacity of Cd, Cu, Zn bound in various chemical form... [more]

Successful energy transitions, also referred to as leapfrog development, present enormous prospects for EU nations to become carbon neutral by shifting from fossil fuels to renewable energy sources. Along with climate change, EU countries must address energy security and dependency issues, exacerbated by factors such as the COVID-19 pandemic, rising energy costs, conflicts between Russia and Ukraine, and political instability. Diversifying energy sources, generating renewable energy, increasing energy efficiency, preventing energy waste, and educating the public about environmental issues are proposed as several strategies. The study draws the conclusion that central European countries may transition to a clean energy economy and become carbon neutral on economic and strategic levels by locating alternative clean energy supply sources, reducing energy use, and producing renewable energy. According to the study, the EU energy industry can be decarbonised and attain energy security using... [more]

This study aims to investigate, from a technical and an environmental perspective, various alternatives for acetic acid concentration for maximizing acetic acid production, its purity, and in the meantime, minimizing the energy usage and the environmental impact. Liquid−liquid extraction followed by azeotropic distillation using different solvents such as: (i) ethyl acetate, (ii) isopropyl acetate, and (iii) a mixture containing isopropyl acetate and isopropanol were first explored, using process flow modeling software. The three cases were compared considering various technical key performance indicators (i.e., acetic acid flow-rate, acetic acid purity, acetic acid recovery, power consumption, thermal energy used, and number of equipment units involved) leading to the conclusion that the usage of the isopropyl acetate—isopropanol mixture leads to better technical results. The isopropanol-isopropyl acetate mixture was furthermore investigated in other two cases where process intensific... [more]

Modern environmental problems are caused by increased energy consumption and the urban heat island effect. Urban noise pollution is another big problem in the Megacities. Ensuring safety with reducing hazards in the urban space is one of the priority tasks of the urban city centers. One solution is the use of green technologies in the construction of office and residential real estate. In this research, we provide the analysis of reducing the noise impact through the use of different green wall systems, such as modular, hydroponic and container, analyzing their benefits and disadvantages in terms of operation and maintenance. After that, we chose hydroponic systems as the most efficient ones and examined different conditions of the system and how these types reduce the noise analyzing absorption coefficient. As a result, we found out that the efficiency of the hydroponic green wall system depends on the humidity of the substrate and the presence of the plants, which confirms the import... [more]

Low global warming potential (GWP) refrigerants for the next-generation air conditioning systems have been investigated with target domestic applications. High-GWP refrigerants are mostly used in climate control applications such as heating, ventilation and air conditioning (HVAC) and refrigeration systems. The majority of refrigerants are responsible for significant environmental issues such as ozone layer depletion and global warming. The Montreal Protocol and the Kyoto Protocol have been implemented to address such issues. In the meantime, authorities in many countries have taken the initiative to phase out the usage of environmentally harmful refrigerants in vapor compression refrigeration systems. Following the global warming mitigation scheme by many signatory countries, research interest has been focused on finding alternative refrigerants with low or ultra-low GWP. This study considered the research trend and development of low-GWP refrigerants while examining system performanc... [more]

In this study, biochar was prepared via hybrid doping of N, O, and S by applying one-pot pyrolysis of poplar wood and S-containing urea formaldehyde at 900 °C. Different doping ratios were adopted, and the contents of O, N, and S were in the ranges of 2.78−5.56%, 2.16−4.92%, and 1.42−4.98%, respectively. This hybrid doping significantly enhanced the efficiency of the removal of tetracycline (40 mg/L) from wastewater to 71.84% in comparison with that attained by using normal poplar biochar (29.45%). The adsorption kinetics and isotherms indicated that the adsorption process was favorable and was dominated by chemisorption instead of physisorption; the dominant adsorption process may be justified by the existence of abundant functional groups. The adsorption capacity was barely related to the surface area (R2 = 0.478), while it was closely related to the concentration of graphitic N (R2 = 0.985) because graphitic N enhanced the π−π interactions. The adsorption capacity was also highly re... [more]

The study of heat transfer deals with the determination of the rate of heat energy transfer from one system to another driven by a temperature gradient. It can be observed in many natural phenomena and is often the fundamental principle behind several engineering systems. Heat transfer analysis is necessary while designing any product. The most common numerical method used to analyze heat transfer is the finite element method. This paper uses the finite element method to demonstrate steady and transient heat conduction in a three-dimensional bracket. The goal here was to determine the temperature distribution and rate of heat flow in the solid. This is crucial in designing machine elements as they are subjected to various thermal loads during operation and also due to fluctuations in the surrounding environmental conditions. The temperature significantly affects stress, displacements, and volumetric strains. Thus, to analyze thermal stresses induced in a machine element, it is necessar... [more]

Solar photovoltaic (PV) deployment is rapidly expanding around the world. However, the soiling factor has an impact on its performance. Saudi Arabia has high solar irradiation and plans to diversify its energy mix for electricity generation by deploying more solar PV across the country. However, it is located in an arid and desert environment, making it a challenging project due to dust accumulation on solar modules. The soiling and PV performance in Saudi Arabia are examined in this paper. Furthermore, it highlights several mitigation techniques that can be used to maintain PV performance through preventive and restorative measures. Furthermore, this study looks into the size and characterization of dust in Saudi Arabia, as well as the entire life cycle of dust accumulation on PV modules. In this review study, the performance of solar PV systems is evaluated under soiling in different regions of Saudi Arabia. Depending on the local environment and other factors, the PV performance has... [more]

The Xishan coalfield is an important coking coal-producing area in China. The No. 8 and No. 9 coals of the Taiyuan formation were sampled and tested from nine mines in the center and north of the Xishan coalfield, and the coal’s quality characteristics, element occurrence characteristics, enrichment characteristics, and sedimentary environment characteristics were analyzed to provide a foundation for clean and efficient coal utilization and identification of associated coal resources. The results obtained from the experiment show that Li in No. 8 coal is the enrichment element. The enrichment coefficient of the U element of ML8 is 13.78, which is close to the industrial index of recycling. The enrichment hazardous elements are Cu, Mo, Cd of ML8, Mo of DQ8, and Th of ZCD8. Along with K value and Sr/Ba ratio, seawater has a greater influence on the south of No. 8 coal than on the north and on the east of No. 9 coal than on the west. No. 8 coal (except ML8) was formed under an oxidation e... [more]

Imaging concentrators like the parabolic trough solar concentrators have been widely employed for energy production in solar power plants. The conventional imaging solar concentrators form a non-uniform Gaussian distribution on receiving absorbers yielding the highest temperatures. The traditional CSP system normally truncated a peripheral region of heat flux to better use the central part. CPV/T systems using the waste heat recovery method can largely improve the total efficiency. However, for the CPV module, the coolant temperature was usually below 80 °C, which limited the applications of the thermal cycle such as the ORC system. In this article, a novel trough-type free-form secondary solar concentrator (TFSC) for PV/Thermal hybrid application has been proposed. Different from other CPV/T concepts using a combined PV panel and cooling tunnel/tube, the current concept separates the receiver in two parts. The secondary free-form reflector is generated by the geometric construction me... [more]

Concrete, an integral part of a nuclear power plant (NPP), experiences degradation during their operational lifetime of the plant. In this review, the major causes of concrete degradation are extensively discussed including mechanisms that are specific to NPPs. The damage mechanism could be chemical or physical. The major causes of chemical degradation include alkali−aggregate reactions, leaching, sulfate attack, bases and acids attack, and carbonation. Physical degradation is a consequence of both environmental and mechanical factors combined. These factors are mainly elevated temperature, radiation, abrasion and erosion, salt crystallization, freeze−thaw distortions, fatigue and vibration. Additionally, steel reinforcements, prestressing steels, liner plates, and structural steel also experience degradation. The prospective areas in the structural components of the NPP where the degradation could occur are mentioned and the effective solutions to the causes of degradation are highlig... [more]

The power attenuation of internal combustion engines in high-altitude environments restricts the performance of unmanned aerial vehicles. Herein, a single-zone model of a hydrogen-doped high-efficiency hybrid cycle rotary engine that considers high-altitude environments was proposed. The indicated values for power, thermal efficiency, and specific fuel cost were used to evaluate the power performance, energy conversion efficiency, and economic performance of the engine, respectively. Then, the effects of adjusting the hydrogen fraction, ignition angle, and rotational speed on high-altitude performance were analyzed. The results showed that high-altitude environments prolonged combustion duration and reduced in-cylinder pressure, thereby causing power attenuation; however, increasing the hydrogen fraction can increase the indicated power. At an altitude of 6 km, the indicated power with a hydrogen fraction of 0.3 was approximately 20.7% higher than that obtained with pure gasoline. The... [more]

A novel combined power and refrigeration system is proposed based on organic Rankine and jet refrigeration cycles. The system has a wider application range and can be adjusted to different cooling and evaporation temperatures. To meet the needs of diverse populations, the cooling and evaporation temperature can be as low as −60 degrees Celsius. The genetic algorithm is used to optimize the system, and the proposed system’s energy, exergy, economy, and environment are analyzed under optimal conditions. The results desmonstrate that the exergy damage, environmental impact rate, and exergy economic coefficient of steam turbine are the largest. The system’s exergy damage and the turbine’s investment cost are reduced, and the system’s performance is improved. The condenser has the greatest potential for improvement and should be considered a priority component for system improvement. In addition, the system parameters are analyzed. Higher low-pressure steam generation temperature, dryness o... [more]

As one of the effective solutions to recover waste heat, absorption refrigeration systems are used in various industrial or refrigeration places. Flat-plate falling-film absorption is one of the newer types, and the lattice Boltzmann method (LBM) has certain advantages compared with the traditional numerical simulation method. In this work, an LBM is used to analyze flat-plate falling-film absorption. Using the additional calculation of the pressure by the pseudo-force model, a lithium bromide−water working fluid−heat and mass transfer model driven by steam partial pressure is realized. The results show that the turbulence generated in the surface wave has a favorable effect on the absorption process; the degree of turbulence gradually decreases with the increase in the Reynolds number, which weakens the increasing effect of the surface wave on the absorption. When the Reynolds number is moderate, the solitary wave flows forward relative to the front thin liquid film, which promotes co... [more]

The Paris Climate Agreement and the 2030 Agenda for Sustainable Development Goals declared by the United Nations set high expectations for the countries of the world to reduce their greenhouse gas (GHG) emissions and to be sustainable. In order to judge the effectiveness of strategies, the evolution of carbon dioxide, methane, and nitrous oxide emissions in countries around the world has been explored based on statistical analysis of time-series data between 1990 and 2018. The empirical distributions of the variables were determined by the Kaplan−Meier method, and improvement-related utility functions have been defined based on the European Green Deal target for 2030 that aims to decrease at least 55% of GHG emissions compared to the 1990 levels. This study aims to analyze the energy transition trends at the country and sectoral levels and underline them with literature-based evidence. The transition trajectories of the countries are studied based on the percentile-based time-series an... [more]

The automotive domain is a very good candidate for energy management, particularly due to the huge amounts of energy lost by heat through exhaust and water-cooling systems. This makes the optimization of vehicle cooling modules directly related to energy consumption and carbon dioxide emission. In this context, contemporary designs that employ diffusers between the forward-facing of an automobile and its heat exchanger subjected to airflow are presented in this work. The ultimate aim is to reduce the fuel consumption and carbon dioxide emissions of vehicles. Based on the aforementioned design, the intensity of the air velocity would be decreased but distributed over a larger exchanger surface. Consequently, the velocity non-uniformity of the airflow upstream would decrease and therefore, the thermal performance would increase. The above-mentioned conclusion is a result of parametric numerical analysis and its associated numerical results that disclosed the enhancement of water-air heat... [more]

With stricter IMO regulations on CO2 taking effect in 2023 and ambitious goals to reduce carbon intensity by 2030, the maritime industry is scrambling to clean up its act. Conventional methods and equipment are now being reevaluated, upgraded or completely replaced. The difference between a short-term fix and a long-term sustainable option is how flexible vessels will be to use new energy sources or technology as they become viable. The review discusses the recent literature on renewable energy sources, technical and operational strategies for new and existing ships, technology maturity, and alternative fuels. It is found that the IMO’s targets can be met by combining two or three technologies, or via a radical technology shift which can provide innovative, high-efficiency solutions from an environmental and economic standpoint. It has also been noted that policies and enforcement are essential management instruments for mitigating the unfavourable environmental effects of marine trans... [more]

Mergers and acquisitions (M&A) may serve as a catalyst in energy transition by accelerating this trend and “greenwashing” the deals. M&A are often used by large energy companies as a tool to explore potential synergy benefits. Recently, M&A strategies in the energy industry have been pursued to transform traditional business models into more “sustainable” models. On the one hand, it may be observed that companies are taking a proactive rather than reactive approach towards environmental-, social-, and governance (ESG)-related M&A deals. On the other hand, sustainable M&A deals do not interest activist shareholders and regulatory authorities only anymore. Inclusion of a sustainability framework and managing ESG-related risks have become part of the overall strategy of most companies within the energy industry. This research addresses the problem of how energy M&A are contributing to sustainable development on the one hand and reflecting sustainable developments on the other hand. The cu... [more]