In this work, a simple, cost-effective successive ionic layer adsorption and reaction (SILAR) deposition technique has been used to deposit a high-quality tin selenide (SnSe) thin film onto a glass substrate. Structural, morphologic, and thermoelectric properties have been characterized for the prepared thin film. X-ray diffraction (XRD) results of the SnSe thin film reveal an orthorhombic structure phase. The morphological properties of the prepared thin films have been studied using field emission scanning electron microscopy (FESEM). The stoichiometric composition of the deposited thin film and the elemental binding energies of the Sn and Se elements have been investigated with energy-dispersive spectroscopy (EDS) and X-ray photoelectron spectroscopy (XPS). The Fourier transformation infrared (FTIR) spectrum of the SnSe thin film displays vibrational modes of chalcogenides bonds. These results suggest that the developed thin film is crystalline, uniform, and without impurities and i... [more]

Superhydrophobic surfaces with non-wetting characteristics have been considered to be potential candidates for ice/frost prevention. In this study, a transparent superhydrophobic coating was created by using a simple method that employed (3-glycidoxypropyl) trimethoxysilane (KH560) and 1,2-Bis (trimethoxysilyl) ethane (D26) as coupling agents and epoxy resin (E51) as an adhesive. The synergy between KH560 and D26 significantly improves the long-term outdoor durability, anti-icing, and anti-frosting performance of the superhydrophobic coating. The coating also has good acid and alkali resistance, UV resistance, and durability. The obtained SiO2@E51@KH560@D26 can delay the freezing time of water by 1974 s, much longer than bare glass (345 s) and also longer than the coatings with only D26 (932 s) or with only KH560 (1087 s). Moreover, the SiO2@E51@KH560@D26 showed an improved anti-frosting capability compared with the other three samples and better maintained its superhydrophobic propert... [more]

In order to achieve high-performance coatings on the surface of electric submersible pump impellers, it is crucial to optimize the laser cladding process parameters. Using Ansys 2021 R1 commercial software, a numerical simulation of laser cladding Ni60 powder on high nickel cast iron was conducted. The simulation utilized a 3D Gaussian heat source, parametric language, and life−death unit technology to replicate the characteristics of synchronous powder delivery laser cladding. The study focused on analyzing the temperature field cloud map and molten pool size under different laser power and scanning speeds, narrowing down the process parameter window, selecting optimized laser power and scanning speed, and assessing the changes in surface morphology, melting height and width, dilution rate, microhardness, and microstructure of the laser cladding coating. Results indicate that the coating width and thickness increase with higher laser power and lower scanning speeds. The microstructure... [more]

A sensitive, easy-to-use, fast, and cost-effective TLC-densitometric method was developed for the separation of metronidazole, secnidazole, ornidazole, tinidazole, and 2-methyl-5-nitroimidazole and for the determination of metronidazole and tinidazole in Metronidazole Polpharma and Tinidazolum Polpharma tablets. Analyses were performed on chromatographic plates precoated with silica gel 60F254 using chloroform + methanol + diethylamine in a volume ratio of 9:1:1 as the optimal mobile phase. The method has been validated. The intraday and interday precision values for the three different concentrations ranged from 0.99% to 1.48% and 0.89% to 1.76%, and the precision values ranged from 1.13% to 2.48% and 0.95% to 2.49% for metronidazole and tinidazole, respectively. The limit of quantification (LOQ) was 0.036 and 0.066 µg/spot for metronidazole and tinidazole, respectively. The mean recovery was 103.1% and 100.6% for metronidazole and tinidazole, respectively. The content of metronidazol... [more]

The low comprehensive compressibility coefficient characteristic of fracture-vuggy reservoirs often leads to imprecise dynamic reserve calculations. This study introduces a novel method for estimating dynamic reserves, which incorporates a modified comprehensive compressibility coefficient to enhance accuracy. This methodology has been applied to 23 wells in the Tahe Oilfield, resulting in error rates substantially lower than those associated with traditional techniques, thereby markedly enhancing the accuracy of dynamic reserve estimations. Specifically, for karst cave and fracture-vuggy reservoirs, the error rate in dynamic reserve calculations is reduced to under 10%, surpassing conventional methods by more than fivefold. In the case of fractured reservoirs, despite minor fluctuations in error rates due to stress sensitivity, diversion capacity, and channel variations, the proposed method still demonstrates a significant reduction in error rates compared to standard practices.

The aging processes of microplastics (MPs) are prevalent in natural environments. Understanding the aging mechanisms of MPs is crucial for assessing their environmental behavior and potential risks. In this study, we selected polylactic acid (PLA) and polyethylene (PE) as representatives of biodegradable and conventional plastics, respectively, to examine changes in their physicochemical properties induced by water and UV light exposure. Laboratory aging resulted in significant fragmentation, characterized by cracks and pores on the surfaces, for both types of MPs, with PLA MPs exhibiting more severe changes, particularly under combined UV and water exposure. Notably, PLA MPs tended to become progressively smaller after aging, whereas PE MPs did not show significant size changes. Chemical analyses of aged MPs using micro-Fourier-transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS) revealed a substantial increase in the carbonyl index (CI) and oxygen content... [more]

In response to the unclear drilling resistance characteristics of rocks in the Ji’yang Depression, low drilling efficiency of PDC drill bits, and difficulties in drill bit selection, this study selected rock samples from different depths in the area for indoor drilling resistance analysis testing. Based on logging data, a prediction model was established for drilling resistance characteristics parameters of the strata in the area, and a graph of drilling resistance characteristic parameters of the rocks in the area was drawn. The study showed that the uniaxial compressive strength of the strata rocks was 50−110 MPa, with a hardness of 500−1300 MPa, a plasticity coefficient ranging from 1 to 2, a rock drillability grade of 8−20, and an abrasiveness index of 5−20. Combining the analysis of on-site drilling bit failures, PDC drill bits adapted to the strata in the area were selected, and the mechanical drilling speed of the selected bits reached 12.58 m/h, successfully drilling through th... [more]

The Paleogene system of the Zhuyi Depression exhibits a pronounced mechanical compaction background. Despite this compaction, remarkable secondary porosity is observed in deep clastic rocks due to dissolution processes, with well-developed hydrocarbon reservoirs persisting in deeper strata. We conducted a comprehensive study utilising various analytical techniques to gain insights into the dissolution and transformation mechanisms of deep clastic rock reservoirs in the steep slope zone of the Lufeng Sag. The study encompassed the collection and analysis of the rock thin sections, XRD whole-rock mineralogy, and petrophysical properties from seven wells drilled into the Eocene. Our findings reveal that the nature of the parent rock, tuffaceous content, dominant sedimentary facies, and the thickness of individual sand bodies are crucial factors that influence the development of high-quality reservoirs under intense compaction conditions. Moreover, the sustained modification and efficient... [more]

This study investigated how welding affects the thermal deformation of square cells produced for casks, which are dry storage containers for spent nuclear fuel. We aimed to minimize structural deformation by utilizing STS316L as the material for the square cells. We explored a method of subdividing the square cells and joining them through butt welding. Keeping the upper plate thickness constant, GTA butt welding was conducted while varying the column’s wall thickness, followed by measurement with a laser vision sensor. The heat conduction and thermal strain were then calculated using a finite element analysis (FEM). Both experimental and analytical results confirmed that there was significant thermal deformation in the cases of thick-walled columns due to variations in heat conduction distribution, with the resulting deformation patterns depending on thickness.

Red ginseng extract is one of the most widely used herbal medicines to prevent and cure various diseases. Among the processed products derived from red ginseng, the water-insoluble part as red ginseng residual (RGR) becomes waste, even though it contains important ingredients. TEMPO-oxidation (TO) can be used as a pre-treatment with different degrees of oxidation (DO) (0 to 0.4) in red ginseng residual (RGR-TO) by introducing chemical oxidation and high-pressure homogenizer (HPH) as a nanofibrillation process. 1H NMR was used to determine the carbohydrate composition and calculate DO, size was examined using a nanoparticle analyzer, and the zeta potential was used to determine surface charge density. RGR-TO with different concentrations had different compositions; glucose and uronic acid were the main ingredients. All treated RGR-TO showed higher oxidant levels than the untreated counterpart (RGR-TO 0). As the oxidant levels increased, the zeta potential and uronic acid increased, but... [more]

This study demonstrates the efficient removal of Alizarin Yellow R anionic dye (AY) from aqueous solutions using green adsorbents. Natural kaolin clay (A1), acid-modified natural clay (A2), chemically treated orange peel (C1) and biochar produced by the thermal treatment of orange peel (C2) were tested for the adsorption of AY. The characteristics of the sorbents were determined by instrumental methods: SEM, EDS, FTIR, BET and TGA. The adsorption experiments were performed under different conditions, including the initial AY dye concentration, adsorbent weight, pH, temperature and contact time. The maximum adsorption capacities had values between 15.72 and 74.62 mg/g at 298 K and the optimal pH of 6.5 at initial concentrations ranging from 30 to 70 mg/L for all adsorbents. The equilibrium data were used for the adsorption isotherm models: Freundlich, Langmuir and Temkin. The Freundlich model fit best for the adsorbents A2, C1 and C2, and the Langmuir isotherm had the highest regression... [more]

This paper presents a practical approach to the production of certified reference materials (CRMs) for ferrosilicon magnesium alloys. These new CRMs are predicted to be used in fast X-ray fluorescence spectrometry (XRF) analysis, which does not require sample digestion and does not result in the production of acidic sewage and emissions, contrary to the classical and instrumental techniques currently used in laboratories. Four new certified reference materials (CRMs) were developed to fill the gap in the reference materials market and ensure fast and traceable analyses. The materials were produced with an industrial process and then homogenized and mixed to achieve the required compositions and level of homogeneity. The homogeneity was determined using specially developed analytical methods and confirmed statistically by ANOVA. Additionally, the results of the tests show the short- and long-term stabilities of the new materials. The certified values for specific element contents were d... [more]

In this paper, a solar thermochemical reactor is designed based on a 5 kW non-coaxial concentrating solar simulator, and a mathematical model is established for thermal calculations. The calculated temperature distribution is used as a load condition for thermal stress analyses. The model is used to study the influence of the solar simulator power, solar reactor inner wall material’s emissivity, working pressure, gas inlet velocity, and thermocouple opening diameter on the thermal stress of the solar reactor. The results show that thermal stress increases with the increase in solar simulator power and the emissivity of the inner wall material in the solar reactor. The inlet velocity and working pressure have little effect on the thermal stress of the reactor and cannot prevent damage to the reactor. In the case of maintaining the diameter of the thermocouple at the front end of the reactor, increasing the diameter of the thermocouple inside the reactor leads to an increase in thermal s... [more]

Dense-phase-tower desulfurization technology is an emerging semi-dry flue-gas desulfurization ash process, i.e., the flue gas is allowed to enter the desulfurization tower from the bottom up and, at the same time, is sprayed with a desulfurizing agent that undergoes an acid−base reaction with the flue gas in the ascent process. The calcium sulfite and calcium sulfate produced by the reaction and the part of the desulfurization agent that is not involved in the reaction will enter the subsequent dust removal system, and what is retained is the by-product desulfurization ash. This desulfurization ash contains a large amount of calcium sulfite, which leads to its unstable nature; it is easily oxidized and expands in volume, and, if used in the field of building materials, it will lead to cracking and other problems, so it is difficult to effectively use it. In order to solve this problem, XRF, XRD, and iodometric and other analytical methods were used to determine the specific composition... [more]

The studies carried out address an important problem for the concrete and asphalt industry, referring to the wear phenomena that affect the elements (flights) of rotary dryers used to dry mineral aggregates. In this article, the authors propose a lifetime estimation method for rotary dryer flights. In order to benefit from greater credibility, the proposed method was applied based on the experimental results obtained, by the authors, in the laboratory, on a stand that reproduces a portion of the real equipment. Starting from these results, the authors identified the mathematical functions used to model the failure rates (wear) of the flights by referring to characteristic quantities for wear evaluation: mass loss of material; reduction in the thickness of the part; surface affected by wear. The experimental data—the input data for the proposed algorithm—correspond to six steels used in industrial applications. The wear phenomenon was modeled considering both the situation of uniform we... [more]

The objective of this study was to determine the effect of XG addition on low-fat yogurt (LFY) properties. Pasteurized skimmed buffalo milk (SBM) was heated to 95 ± 2 °C for 16 s, cooled to 40 ± 1 °C, and then divided into six treatment lots. The treatments included the following: T1 (control), T2 (0.2% XG), T3 (0.4% XG), T4 (0.6% XG), T5 (0.8% XG), and T6 (1% XG). A proportion of 2% of a mixed starter culture from Streptococcus thermophilus (ST), Lactobacillus bulgaricus (LB), and Bifidobacterium bifidum (BB) in the ratio 1:1:1 was added. Yogurt was manufactured following the standard manufacturing protocol. Chemical composition and texture were determined at fresh time, while water-holding capacity (WHC), viscosity, and syneresis % were determined at 0, 7, 14, and 21 days of storage. Total bacterial counts (TBC), lactobacilli, streptococci, and bifidobacteria counts were determined at 0, 7, 14, and 21 days of storage. Sensory analysis was performed immediately upon the cooling stage... [more]

The low-permeability argillaceous rock mass is an unfavorable geological body commonly found in the construction process of underground engineering conditions such as roadways and tunnels. Due to the compact structure and low permeability of the rock mass, grouting with conventional materials cannot effectively seal the micro-cracks of the rock mass. Based on the low efficiency of high-pressure grouting of nano-silica sol, this paper preliminarily explores the regularities and mechanism of grouting and pore sealing of low-permeability rock mass under the action of silica sol imbibition from the aspects of gelling properties of silica sol, core pore structure, imbibition law, and pore sealing characteristics. The results show the following: (1) The increase in particle size during the gel process reduced the injectability and wettability of the silica sol. The imbibition properties of silica sol were time-varying, and the deterioration inflection points of injectability and wettability... [more]

Protection from nuclear biochemical aerosol and air pollution pays attention to aerosol mass concentration. The concentration of upstream aerosol of the commonly used filtration efficiency detection device for high-efficiency filter materials is low, making it insufficient for detecting the filtration efficiency of high-efficiency filter materials. This study designed and built a set of filtration efficiency detection devices for high-efficiency filter materials based on mass concentration. By adjusting the oil bath temperature, injection pressure, the degree of spiral-separator separation, as well as the number and size of nozzles, we investigated the effects of each condition on the concentration and particle size distribution of aerosol generation. As a result, the oil mist generator of the device can stably generate high-concentration aerosol with a mass concentration of up to 1587.9 mg/m3 and a number concentration of up to 107−108 P/cm3. The high-concentration aerosol generated c... [more]

A series of COMSOL numerical models were developed to explore how confining pressure impacts the microscopic structure and hydraulic conductivity of Geosynthetic Clay Liners (GCLs), taking into account the bentonite swelling ratio, mobile porosity, pore size, and tortuosity of the main flow path. The study reveals that the mobile porosity and pore size are critical factors affecting GCL hydraulic conductivity. As confining pressure increases, the transition of mobile water to immobile water occurs, resulting in a reduction in mobile water volume, the narrowing of pore channels, decreased flow velocity, and diminished hydraulic conductivity within the GCL. Mobile porosity undergoes a slight decrease from 0.273 to 0.104, while the ratio of mobile porosity to total porosity in the swelling process decreases significantly from 0.672 to 0.256 across the confining pressure range from 50 kPa to 500 kPa, which indicates a transition of mobile water toward immobile water. The tortuosity of the... [more]

This article presents the results of cyanide leaching of gold-containing concentrate using the trichlorocyanuric acid (TCCA) oxidizer. Gold-containing concentrate was obtained from a gold tailings sample from a gold recovery factory (GRF) in one of the deposits of Kazakhstan that have not previously been studied for concentrability. According to X-ray phase analysis and energy dispersive spectrometry (DSM) data, the main compounds in the tailings sample under study are pyrite FeS2, quartz SiO2, calcite CaCO3, albite NaAlSi3O8, muscovite KAl2Si3AlO10(OH)8, dolomite CaMg(CO3)2, and oxidized iron compounds. Microscopic studies of the concentrate have established the presence of ultrafine gold with sizes from Au 0.9 to 10.2 μm in pyrite. Obtaining the gold-containing concentrate with a gold content of 15.95 g/t is possible according to the enrichment scheme, which includes centrifugal separation, classification according to the fineness class −0.05 mm, additional grinding of hydrocyclone s... [more]

Polystyrene plastics present significant environmental and human health threats due to their poor recyclability and degradability. However, leveraging their properties to enhance material performance stands out as one of the most effective strategies for mitigating these issues. Here, we have employed recycled expanded polystyrene plastics to manufacture metal−organic framework/expanded polystyrene plastic composites (MOF@EPP) using an adverse solvent precipitation method. This method simultaneously recycles EPPs and safeguards moisture-sensitive MOFs. Due to the exceptional hydrophobic properties of EPPs, HKUST−1@EPP can maintain structural integrity even when immersed in water for 30 days. This method is applicable to other moisture-sensitive MOFs, such as MOF−74(Zn) and MIL−53(Al). The HKUST−1@EPP composite also exhibits desirable heterogeneous catalytic activity in the Knoevenagel condensation reaction between benzaldehyde and acrylonitrile. The conversion rate can reach 94.9% with... [more]

Magnetic nanofluids, also referred to as ferromagnetic particle levitation systems, are materials with highly responsive magnetic properties. Due to their magnetic responsiveness, excellent controllability, favorable thermal characteristics, and versatility, magnetic nanofluids have sparked considerable interest in both industrial manufacturing and scientific research. Magnetic nanofluids have been used and developed in diverse areas such as materials science, physics, chemistry and engineering due to their remarkable characteristics such as rapid magnetic reaction, elastic flow capacities, and tunable thermal and optical properties. This paper provides a full and in-depth introduction to the diverse uses of ferrofluids including material fabrication, fluid droplet manipulation, and biomedicine for the power and machinery sectors. As a result, magnetic nanofluids have shown promising applications and have provided innovative ideas for multidisciplinary research in biology, chemistry, p... [more]

Industrial pure zirconium plays an essential role as a structural material in the nuclear energy sector. Understanding the deformation mechanisms is crucial for effectively managing the plasticity and texture evolution of industrial pure zirconium. In the present study, the texture and microstructure evolution of industrial pure zirconium during the cold-rolling process have been characterized by XRD, EBSD, and TEM. The influences of various twins on texture evolution have also been simulated by the reaction stress model. The effects of slip and twinning on the deformation behavior and texture evolution have been discussed based on crystallographic and experimental considerations. Cold rolling yields a typical bimodal texture, resulting in the preferential //RD orientation. The activation of the deformation mechanisms during cold rolling follows the sequential trend of slip, twinning, local slip. Experimental characterization and reaction stress simulation illustrate that T1 twins domi... [more]

With the application of CO2 fracturing, CO2 huff and puff, CO2 flooding, and other stimulation technologies in shale reservoirs, a large amount of CO2 remained in the formation, which also lead to the serious corrosion problem of CO2 in shale reservoirs. In order to solve the harm caused by CO2 corrosion, it is necessary to curb CO2 corrosion from the cementing cement ring to ensure the long-term stable exploitation of shale oil. Therefore, a new latex was created using liquid polybutadiene, styrene, 2-acrylamide-2-methylpropanesulfonic acid, and maleic anhydride to increase the cement ring’s resistance to CO2 corrosion. The latex’s structure and characteristics were then confirmed using infrared, particle size analyzer, thermogravimetric analysis, and transmission electron microscopy. The major size distribution of latex is between 160 and 220 nm, with a solid content of 32.2% and an apparent viscosity of 36.8 mPa·s. And it had good physical properties and stability. Latex can effecti... [more]

Mineralized materials are gaining increased interest recently in a number of fields, especially in bone tissue engineering as bone replacement materials as well as in the architecture-built environment as structural building materials. Until the moment, there has not been a unified sustainable approach that addresses this multi-scale application objective by developing a self-mineralized material with minimum consumption of materials and processes. Thus, in the current study, a hydrogel developed from sodium alginate, gelatine, and calcium phosphate dibasic (CPDB) was optimized in terms of rheological properties and mineralization capacity through the formation of hydroxyapatite crystals. The hydrogel composition process adopted a three-stage, thermally induced chemical cross-linking to achieve a stable and enhanced hydrogel. The 6% CPDB-modified SA−gelatine hydrogel achieved the best rheological properties in terms of elasticity and hardness. Different concentrations of epigallocatech... [more]