In order to explore the dynamic characteristics of the mechanical seal under different fault degrees, this paper selected the upstream pumping mechanical seal as the object of study. The research established the rotating ring-fluid film-stationary ring 3D model, which was built to analyze the fault mechanism. To study extrusion fault mechanism and characteristics, different dynamic parameters were used in the analysis process. Theoretical analysis, numerical simulation, and comparison were conducted to study the relationship between the fault degree and dynamic characteristics. It is the first time to research the dynamic characteristics of mechanical seals in the specific extrusion fault. This paper proved feasibility and effectiveness of the new analysis method. The fluid film thickness and dynamic characteristics could reflect the degree of the extrusion fault. Results show that the fluid film pressure fluctuation tends to be more intensive under the serious extrusion fault conditio... [more]

This paper proposes a feature selection (FS) approach, namely, correlation and fitness value-based feature selection (CFFS). CFFS is an improvement feature selection approach of correlation-based feature selection (CFS) for the common failure cases of the induction motor. CFFS establishes the induction motor fault detection (FD) system with artificial neural network (ANN). This study analyzes the current signal of the induction motor with multiresolution analysis (MRA), extracts the features, and uses feature selection approaches (ReliefF, CFS, and CFFS) to reduce the number of features and maintain the accuracy of the induction motor fault detection system. Finally, the induction motor fault detection system is trained by the feature selection approaches selected features. The best induction motor fault detection system will be established through the comparison of the efficiency of these FS approaches.

Due to the complex structure and wide excitation of the range extender, the misalignment and stator short-circuit coupling fault can easily occur. Therefore, it is necessary to study the coupling fault mechanism of the range extender, analyze the cause of the fault and the fault evolution law, and research the coupling fault characteristics. To reveal the mechanism of misalignment and stator-short-circuit coupling fault, the misalignment mechanism was analyzed and the bending and torsion electromagnetic stiffness of the generator in the stator short-circuit fault was derived. Then the dynamic model of bending and torsion coupling for the generator was established. Furthermore, we used the Runge-Kutta method to study the vibration response characteristics of generator rotor under coupling fault. Then through finite element analysis, the feasibility of coupled fault diagnosis was verified. The results show that the response of the generator rotor not only has the frequency component of s... [more]

The present work presents a methodology based on data reconciliation to monitor membrane separation processes reliably, online and in real time for the first time. The proposed methodology was implemented in accordance with the following steps: data acquisition; data pre-treatment; data characterization; data reconciliation; gross error detection; and critical evaluation of measured data with a soft sensor. The acquisition of data constituted the slowest stage of the monitoring process, as expected in real-time applications. The pre-treatment stage was fundamental to assure the robustness of the code and the initial characterization of collected data was carried out offline. The characterization of the data showed that steady-state modeling of the process would be appropriate, also allowing the implementation of faster numerical procedures for the data reconciliation step. The data reconciliation step performed well, quickly and consistently. Thus, data reconciliation allowed the estim... [more]

Ibuprofen is one of the best-known nonsteroidal anti-inflammatory and analgesic drugs. Following the previous work, the current study is focused on estimating the effect of different chromatographic conditions on the sensitivity of thin-layer chromatography in combination with UV densitometry, i.e., the detection and quantification of ibuprofen in a wide range of its concentrations including the lowest limits of detection (LOD) and quantification (LOQ). For this purpose, a reliable and easy-to-use calculation procedure for LOD and LOQ determination is presented in this work. In addition, the impact of type plates and mobile phase composition on the LOD and LOQ, respectively, of this active substance is accurately described. The results of detection and the quantification level of ibuprofen obtained under applied chromatographic conditions confirmed the utility of silica gel plates as well as silica gel bonded phases (i.e., reversed-phase (RP) plates) in the thin-layer chromatography (T... [more]

Diagnosis of bearing faults is crucial in various industries. Time series classification (TSC) assigns each time series to one of a set of pre-defined classes, such as normal and fault, and has been regarded as an appropriate approach for bearing fault diagnosis. Considering late and inaccurate fault diagnosis may have a significant impact on maintenance costs, it is important to classify bearing signals as early and accurately as possible. TSC, however, has a major limitation, which is that a time series cannot be classified until the entire series is collected, implying that a fault cannot be diagnosed using TSC in advance. Therefore, it is important to classify a partially collected time series for early time series classification (ESTC), which is a TSC that considers both accuracy and earliness. Feature-based TSCs can handle this, but the problem is to determine whether a partially collected time series is enough for a decision that is still unsolved. Motivated by this, we propose... [more]

A convolutional neural network (CNN) has been used to successfully realize end-to-end bearing fault diagnosis due to its powerful feature extraction ability. However, the CNN is prone to focus on local information, ignoring the relationship between the whole and the part of the signal due to its unique structure. In addition, it extracts some fault features with poor robustness under noisy environment. A novel diagnosis model based on feature fusion and feature selection, GL-mRMR-SVM, is proposed to address this problem in this paper. First, the model combines the global features in the time-domain and frequency-domain of the raw data with the local features extracted by CNN to make full use of the signal information and overcome the weakness of traditional CNNs neglecting the overall signal. Then, the max-relevance min-redundancy (mRMR) algorithm is used to automatically extract the discriminative features from the fused features without any prior knowledge. Finally, the extracted dis... [more]

This paper presents a monitoring framework to detect drifts and faults in the behavior of the central processing unit (CPU)-graphics processing unit (GPU) chips powering them. To construct the framework, an incremental model and a fault detection and isolation (FDI) algorithm are hereby proposed. The reference model is composed of a set of interconnected exchangeable subsystems that allows it to be adapted to changes in the structure of the system or operating modes, by replacing or extending its components. It estimates a set of variables characterizing the operating state of the chip from only two global inputs. Then, through analytical redundancy, the estimated variables are compared to the output of the system in the FDI module, which generates alarms in the presence of faults or drifts in the system. Furthermore, the interconnected nature of the model allows for the direct localization and isolation of any detected abnormalities. The implementation of the proposed framework requir... [more]

Timely monitoring and control of critical process parameters and product attributes are still the basic tasks in bioprocess development. The current trend of automation and digitization in bioprocess technology targets an improvement of these tasks by reducing human error and increasing through-put. The gaps in such automation procedures are still the sampling procedure, sample preparation, sample transfer to analyzers, and the alignment of process and sample data. In this study, an automated sampling system and the respective data management software were evaluated for system performance; applicability with HPLC for measurement of vitamins, product and amino acids; and applicability with a biochemical analyzer. The focus was especially directed towards the adaptation and assessment of an appropriate amino acid method, as these substances are critical in cell culture processes. Application of automated sampling in a CHO fed-batch revealed its potential with regard to data evaluation. T... [more]

Industry 4.0 (I4.0) represents the Fourth Industrial Revolution in manufacturing, expressing the digital transformation of industrial companies employing emerging technologies. Factories of the future will enjoy hybrid solutions, while quality is the heart of all manufacturing systems regardless of the type of production and products. Quality 4.0 is a branch of I4.0 with the aim of boosting quality by employing smart solutions and intelligent algorithms. There are many conceptual frameworks and models, while the main challenge is to have the experience of Quality 4.0 in action at the workshop level. In this paper, a hybrid model based on a neural network (NN) and expert system (ES) is proposed for dealing with control chart patterns (CCPs). The idea is to have, instead of a passive descriptive model, a smart predictive model to recommend corrective actions. A construction plaster-producing company was used to present and evaluate the advantages of this novel approach, while the result... [more]

Various types of risks exist in a supply chain, and disruptions could lead to economic loss or even breakdown of a supply chain without an effective mitigation strategy. The ability to detect disruptions early can help improve the resilience of the supply chain. In this paper, the application of principal component analysis (PCA) and dynamic PCA (DPCA) in fault detection and diagnosis of a supply chain system is investigated. In order to monitor the supply chain, data such as inventory levels, market demands and amount of products in transit are collected. PCA and DPCA are used to model the normal operating conditions (NOC). Two monitoring statistics, the Hotelling's T-squared and the squared prediction error (SPE), are used to detect abnormal operation of the supply chain. The confidence limits of these two statistics are estimated from the training data based on the $\chi^2$- distributions. The contribution plots are used to identify the variables with abnormal behavior when at le... [more]

Graphene is a material gaining attention as a candidate for new application fields such as chemical sensing. In this review, we discuss recent advancements in the field of hydrogen gas sensors based on graphene. Accordingly, the main part of the paper focuses on hydrogen gas sensors and examines the influence of different manufacturing scenarios on the applicability of graphene and its derivatives as key components of sensing layers. An overview of pristine graphene customization methods is presented such as heteroatom doping, insertion of metal/metal oxide nanosized domains, as well as creation of graphene-polymer blends. Volumetric structuring of graphene sheets (single layered and stacked forms) is also considered as an important modifier of its effective use. Finally, a discussion of the possible advantages and weaknesses of graphene as sensing material for hydrogen detection is provided.

Degradation state recognition and failure prediction are the key steps of prognostic and health management (PHM), which directly affect the reliability of the equipment and the selection of preventive maintenance strategy. Given the problem that the distinction between feature vectors is not obvious and the accuracy of fault prediction is low, a method based on multi-class Gaussian process classification and Gaussian process regression (GPR) is studied by the vibration signal and flow signal in six degraded states of the axial piston pump. For degradation state recognition, the variational mode decomposition (VMD) was used to decompose the vibration signal, and obtaining intrinsic mode function (IMF) components with rich information. Subsequently, multi-scale permutation entropy (MPE) was employed to select feature vectors of IMF components in different states. In order to reduce feature dimensions and improve recognition performance, ReliefF was used to select feature vectors with hig... [more]

In conditional microbial screening, a limited number of candidate strains are tested at different conditions searching for the optimal operation strategy in production (e.g., temperature and pH shifts, media composition as well as feeding and induction strategies). To achieve this, cultivation volumes of >10 mL and advanced control schemes are required to allow appropriate sampling and analyses. Operations become even more complex when the analytical methods are integrated into the robot facility. Among other multivariate data analysis methods, principal component analysis (PCA) techniques have especially gained popularity in high throughput screening. However, an important issue specific to high throughput bioprocess development is the lack of so-called golden batches that could be used as a basis for multivariate analysis. In this study, we establish and present a program to monitor dynamic parallel cultivations in a high throughput facility. PCA was used for process monitoring and a... [more]

In mammalian cell culture, especially in pharmaceutical manufacturing, pH is a critical process parameter that has to be controlled as accurately as possible. Not only does pH directly affect cell culture performance, ensuring a comparable pH is also crucial for scaling and transfer of processes. A sample-based offline pH measurement is commonly used to ensure correct bioreactor pH probe signals after sterilization and as a detection measure for drifts of probe signals. However, the sample-based pH offline measurement does not necessarily deliver required accuracy. Offsets between bioreactor pH and sample pH heavily depend on equipment, local procedures and the offline measurement method that is used. This article adequately describes a novel, non-invasive method to determine pH and pCO2 in sterile bioreactors without the need to sample and measure offline. This method utilizes the chemical correlation between carbon dioxide in the gas phase, dissolved carbon dioxide, bicarbonate and d... [more]

State of charge (SOC) is one of the most important parameters in battery management systems, as it indicates the available battery capacity at every moment. There are numerous battery model-based methods used for SOC estimation, the accuracy of which depends on the accuracy of the model considered to describe the battery dynamics. The SOC estimation method proposed in this paper is based on an Extended Kalman Filter (EKF) and nonlinear battery model which was parameterized using extended laboratory tests performed on several 13 Ah lithium titanate oxide (LTO)-based lithium-ion batteries. The developed SOC estimation algorithm was successfully verified for a step discharge profile at five different temperatures and considering various initial SOC initialization values, showing a maximum SOC estimation error of 1.16% and a maximum voltage estimation error of 44 mV. Furthermore, by carrying out a sensitivity analysis it was showed that the SOC and voltage estimation error are only slightl... [more]

Power quality disturbances (PQD) in electric distribution systems can be produced by the utilization of non-linear loads or environmental circumstances, causing electrical equipment malfunction and reduction of its useful life. Detecting and classifying different PQDs implies great efforts in planning and structuring the monitoring system. The main disadvantage of most works in the literature is that they treat a limited number of electrical disturbances through personal computer (PC)-based computation techniques, which makes it difficult to perform an online PQD classification. In this work, the novel contribution is a methodology for PQD recognition and classification through discrete wavelet transform, mathematical morphology, decomposition of singular values, and statistical analysis. Furthermore, the timely and reliable classification of different disturbances is necessary; hence, a field programmable gate array (FPGA)-based integrated circuit is developed to offer a portable hard... [more]

This article states a condition monitoring strategy for wind turbines using a statistical data-driven modeling approach by means of supervisory control and data acquisition (SCADA) data. Initially, a baseline data-based model is obtained from the healthy wind turbine by means of multiway principal component analysis (MPCA). Then, when the wind turbine is monitorized, new data is acquired and projected into the baseline MPCA model space. The acquired SCADA data are treated as a random process given the random nature of the turbulent wind. The objective is to decide if the multivariate distribution that is obtained from the wind turbine to be analyzed (healthy or not) is related to the baseline one. To achieve this goal, a test for the equality of population means is performed. Finally, the results of the test can determine that the hypothesis is rejected (and the wind turbine is faulty) or that there is no evidence to suggest that the two means are different, so the wind turbine can be... [more]

This article offers reasons to defend the use of generic behavior models as opposed to specific models in applications to determine component degradation. The term generic models refers to models based on operating data from various units, whereas specific models are calculated using operating data taken from a single unit. Moreover, generic models, used in combination with a status indicator, show excellent capacity for detecting anomalies in the equipment and for evaluating the effectiveness of the maintenance actions, resulting in lower development and maintenance costs for the operating firm. Artificial neural networks and moving means were used to calculate the degradation indicators, based on the remainders in the model. The models were developed from operating data from fourteen wind turbines monitored over several years, and applied to the detection of faults in the bearings on the non-drive end of the generator. The use of generic models may not be recommendable for detecting... [more]

The electrical system of a wind farm has a significant influence on the wind farm reliability and electrical energy yield. The disconnect switch installed in an electrical system cannot only improve the operating flexibility, but also enhance the reliability for a wind farm. Therefore, this paper develops a probabilistic transfer technique for integrating the electrical topology structure, the isolation operation of disconnect switch, and stochastic failure of electrical equipment into the reliability assessment of wind farm electrical system. Firstly, as the traditional two-state reliability model of electrical equipment cannot consider the isolation operation, so the paper develops a three-state reliability model to replace the two-state model for incorporating the isolation operation. In addition, a proportion apportion technique is presented to evaluate the state probability. Secondly, this paper develops a probabilistic transfer technique based on the thoughts that through transfe... [more]

Background: Identifying the health status of wind turbines becomes critical to reduce the impact of failures on generation costs (between 25⁻35%). This is a time-consuming task since a human expert has to explore turbines individually. Methods: To optimize this process, we present a strategy based on Self Organizing Maps, clustering and a further grouping of turbines based on the centroids of their SOM clusters, generating groups of turbines that have similar behavior for subsystem failure. The human expert can diagnose the wind farm health by the analysis of a small each group sample. By introducing post-processing tools like Class panel graphs and Traffic lights panels, the conceptualization of the clusters is enhanced, providing additional information of what kind of real scenarios the clusters point out contributing to a better diagnosis. Results: The proposed approach has been tested in real wind farms with different characteristics (number of wind turbines, manufacturers, power,... [more]

Induction motors consume a great portion of the generated electrical energy. Moreover, most of them work at underloaded conditions, so they have low efficiencies and waste a lot of energy. Because of this, the efficiency estimation of in-service induction motors is a matter of great importance. This efficiency estimation is usually performed through indirect methods, which do not require invasive measurements of torque or speed. One of these methods is the modified Air-Gap Torque (AGT) method, which only requires voltage and current data, the stator resistance value, and the mechanical losses. This paper approaches the computation of a modified stator resistance including the mechanical losses effect to be applied in the AGT method for torque and efficiency estimation of induction motors. Some improvements are proposed in the computation of this resistance by using a direct method, as well as the possibility to estimate this parameter directly from the nameplate data of the induction m... [more]

In this work, a systematic approach based on the geometric observer is proposed to design a model-based soft sensor, which allows the estimation of quality indexes in a bioreactor. The study is focused on the structure design problem where the set of innovated states has to be chosen. On the basis of robust exponential estimability arguments, it is found that it is possible to distinguish all the unmeasured states if temperature and dissolved oxygen concentration measurements are combined with substrate concentrations. The proposed estimator structure is then validated through numerical simulation considering two different measurement processor algorithms: the geometric observer and the extended Kalman filter.

Conventional leak detection techniques require improvements to detect small leakage (<10%) in gas mixture pipelines under transient conditions. The current study is aimed to detect leakage in gas mixture pipelines under pseudo-random boundary conditions with a zero percent false alarm rate (FAR). Pressure and mass flow rate signals at the pipeline inlet were used to estimate mass flow rate at the outlet under leak free conditions using Hammerstein model. These signals were further used to define adaptive thresholds to separate leakage from normal conditions. Unlike past studies, this work successfully detected leakage under transient conditions in an 80-km pipeline. The leakage detection performance of the proposed methodology was evaluated for several leak locations, varying leak sizes and, various signal to noise ratios (SNR). Leakage of 0.15 kg/s—3% of the nominal flow—was successfully detected under transient boundary conditions with a F-score of 99.7%. Hence, it can be conclude... [more]

Monitoring process variables in bioprocesses with complex expression systems, such as filamentous fungi, requires a vast number of offline methods or sophisticated inline sensors. In this respect, cell viability is a crucial process variable determining the overall process performance. Thus, fast and precise tools for identification of key process deviations or transitions are needed. However, such reliable monitoring tools are still scarce to date or require sophisticated equipment. In this study, we used the commonly available size exclusion chromatography (SEC) HPLC technique to capture impurity release information in Penicillium chrysogenum bioprocesses. We exploited the impurity release information contained in UV chromatograms as fingerprints for development of principal component analysis (PCA) models to descriptively analyze the process trends. Prediction models using well established approaches, such as partial least squares (PLS), orthogonal PLS (OPLS) and principal component... [more]