Chemical looping combustion (CLC) technology generates power while capturing CO2 inherently with no direct energy penalty. However, previous studies have shown significant energy penalties due to low turbine inlet temperature (TIT) relative to a standard natural gas combined cycle plant. The low TIT is limited by the oxygen carrier material used in the CLC process. Therefore, in the current study, an additional combustor is included downstream of the CLC air reactor to raise the TIT. The efficient production of clean hydrogen for firing the added combustor is key to the success of this strategy. Therefore, the highly efficient membrane-assisted chemical looping reforming (MA-CLR) technology was selected. Five different integrations between CLC and MA-CLR were investigated, capitalizing on the steam in the CLC fuel reactor outlet stream to achieve highly efficient reforming in MA-CLR. This integration reduced the energy penalty as low as 3.6%-points for power production only (case 2) an... [more]

The objective of this study is to assess the techno-economic potential of the proposed novel energy system, which allows for negative emissions of carbon dioxide (CO2). The analyzed system comprises four main subsystems: a biomass-fired combined heat and power plant integrated with a CO2 capture and compression unit, a CO2 transport pipeline, a CO2-enhanced geothermal system, and a supercritical CO2 Brayton power cycle. For the purpose of the comprehensive techno-economic assessment, the results for the reference biomass-fired combined heat and power plant without CO2 capture are also presented. Based on the proposed framework for energy and economic assessment, the energy efficiencies, the specific primary energy consumption of CO2 avoidance, the cost of CO2 avoidance, and negative CO2 emissions are evaluated based on the results of process simulations. In addition, an overview of the relevant elements of the whole system is provided, taking into account technological progress and tec... [more]

In this study, the thermal stability and corrosivity of various CO2-loaded tertiary amine blends in both aqueous and non-aqueous form in stainless steel cylinders were studied for combined acid gas and water removal. The thermal stability was measured from the remaining amine concentration and the corrosivity was measured from the amount of various metals in blends using titration and inductively coupled plasma mass spectrometry (ICP-MS), respectively. The experimental data were used to calculate the rate constants of amine group loss. The developed model represented the experimental data very well. Solvent change from H2O to triethylene glycol (TEG) in blends decreased the thermal stability and vice versa for corrosivity. The amine stability was increased when contact with stainless steel was reduced. An increase in the amine concentration or CO2 loading at constant temperature decreased the thermal stability and vice versa for corrosivity.

The increase of capital investments and operation and maintenance (O&M) costs represents a current limitation to the diffusion of carbon capture systems for the clean combustion of fossil fuels. However, post-combustion systems, such as calcium looping (CaL), for CO2 capture from flue gas are the most attractive carbon capture systems since they can be installed at new plants and retrofitted into existing power plants. This work investigates the pros and cons of employing a calcium looping system for CO2 capture and also as a desulphurization unit. A preliminary techno-economic analysis was carried out comparing a base case consisting of a coal-based power plant of about 550MWe with a desulphurization unit (Case 1), the same plant but with a CaL system added for CO2 capture (Case 2), or the same plant but with a CaL system for simultaneous capture of CO2 and SO2 and the removal of the desulphurization unit (Case 3). Case 2 resulted in a 67% increase of capital investment with respect t... [more]

The presented work is focused on biomass thermochemical conversion with integrated CO2 capture. The main aim of this study was the in-depth investigation of the impact of pyrolysis temperature (500, 600 and 700 °C) and CaO sorbent addition on the chemical and physical properties of obtained char and syngas. Under the effect of the pyrolysis temperature, the properties of biomass chars were gradually changed, and this was confirmed by examination using thermal analysis, scanning electron microscopy, X-ray diffraction, and porosimetry methods. The chars were characterised by a noticeable carbon content (two times at 700 °C) resulting in a lower O/C ratio. The calculated combustion indexes indicated the better combustible properties of chars. In addition, structural morphology changes were observed. However, the increasing pyrolysis temperature resulted in changes of solid products; the differences of char properties were not significant in the range of 500 to 700 °C. Syngas was analysed... [more]

Calcium looping is a promising technology to capture CO2 from the process of coal-fired power generation and gasification of coal/biomass for hydrogen production. The decay of CO2 capture activities of calcium-based sorbents is one of the main problems holding back the development of the technology. Taking carbide slag as a main raw material and Ca12Al14O33 as a support, highly active CO2 sorbents were prepared using the hydrothermal template method in this work. The effects of support ratio, cycle number, and reaction conditions were evaluated. The results show that Ca12Al14O33 generated effectively improves the cyclic stability of CO2 capture by synthetic sorbents. When the Al2O3 addition is 5%, or the Ca12Al14O33 content is 10%, the synthetic sorbent possesses the highest cyclic CO2 capture performance. Under harsh calcination conditions, the CO2 capture capacity of the synthetic sorbent after 30 cycles is 0.29 g/g, which is 80% higher than that of carbide slag. The superiority of t... [more]

This study determines and presents the capital and operating costs imposed by the use of CO2 capture technologies in the refining and petrochemical sectors. Depending on the refining process and the CO2 capture method, CO2 emissions costs of EUR 30 to 40 per ton of CO2 can be avoided. Advanced low-temperature CO2 capture technologies for upgrading oxyfuel reformers may not provide any significant long-term and short-term benefits compared to conventional technologies. For this reason, an analysis was performed to estimate the CO2 reduction potential for the oil and gas industries using short- and long-term ST/MT technologies, was arriving at a reduction potential of about 0.5−1 Gt/yr. The low cost of CO2 reduction is a result of the good integration of CO2 capture into the oil production process. The results show that advanced gasoline fraction recovery with integrated CO2 capture can reduce the cost of producing petroleum products and reduce CO2 emissions, while partial CO2 capture ha... [more]

Direct study of CO2 capture efficiency during microalgae Arthrospira platensis cultivation at high CO2 concentrations was carried out. Microalgae were grown in a 90 L photobioreactor on Zarrouk’s medium prepared with distilled water. Three 15-day experiments were carried out with different initial CO2 concentrations: 1, 5, and 9 vol.%. During the experiments, both the change in the optical density of the microalgae suspension and the direct change in the CO2 concentration in the chamber were measured. The maximum decrease in CO2 concentration due to the growth of microalgae was 0.10 vol.% (CO2)/day in the experiment with an initial CO2 concentration of 5 vol.%. Growth rate of biomass density was 79.4, 76.3, and 48.4 (mg/L)/day at 1, 5, and 9 vol.% CO2 concentrations, respectively. During the experiment with initial CO2 concentrations of 1 and 5 vol.%., pH of the culture medium was increased, but pH was decreased from 9.2 to 8.8 at 9 vol.%. In general, good viability (high quality of bi... [more]

This paper is devoted to improvement of environmental safety in hydrocarbon-firing TPPs. Despite the development of renewable power sources, the number of traditional power production facilities continues its growth. The toxic emission mitigation in traditional TPPs has been deeply investigated, but the problem of greenhouse gas atmospheric emissions is of topical interest. Oxy-fuel technology reduces CO2 emissions and is highly efficient and environmentally safe. Also, it requires relatively low capital investments. Thermal efficiency analysis shows that the Allam cycle facilities have the best efficiency. Their thermodynamic parameters can be optimized with minimal primary costs and capital investments. This newly developed analysis was used to compare the investment efficiency of projects for the buildup of oxy-fuel and combined cycle facilities. Without emission quote payments, the NPV of combined cycle projects is 16% higher, as well as having a lower DPP. The electricity producti... [more]

One of the alternatives to reduce CO2 emissions from industrial sources (mainly the oil and gas industry) is CO2 capture. Absorption with chemical solvents (alkanolamines in aqueous solutions) is the most widely used conventional technology for CO2 capture. Despite the competitive advantages of chemical solvents, the technological challenge in improving the absorption process is to apply alternative solvents, reducing energy demand and increasing the CO2 captured per unit of solvent mass. This work presents an experimental study related to the kinetic and thermodynamic analysis of high-pressure CO2 capture using ethylenediamine (EDA) as a chemical solvent. EDA has two amine groups that can increase the CO2 capture capacity per unit of solvent. A non-stirred experimental setup was installed and commissioned for CO2 capture testing. Tests of the solubility of CO2 in water were carried out to validate the experimental setup. CO2 capture testing was accomplished using EDA in aqueous soluti... [more]

This study investigated the effect of HCl in biomass gasification producer gas on the CO2 capture efficiency and contaminants removal efficiency by CaO-Fe2O3 based sorbent material in the calcium looping process. Experiments were conducted in a fixed bed reactor to capture CO2 from the producer gas with the combined contaminants of HCl at 200 ppmv, H2S at 230 ppmv, and NH3 at 2300 ppmv. The results show that with presence of HCl in the feeding gas, sorbent reactivity for CO2 capture and contaminants removal was enhanced. The maximum CO2 capture was achieved at carbonation temperatures of 680 °C, with efficiencies of 93%, 92%, and 87%, respectively, for three carbonation-calcination cycles. At this carbonation temperature, the average contaminant removal efficiencies were 92.7% for HCl, 99% for NH3, and 94.7% for H2S. The outlet contaminant concentrations during the calcination process were also examined which is useful for CO2 reuse. The pore structure change of the used sorbent materi... [more]

We report on a simple electrochemical system able to capture gaseous carbon dioxide from a gas mixture and convert it into syngas. The capture/release module is implemented via regeneration of NaOH and acidification of NaHCO3 inside a four-chamber electrochemical flow cell employing Pt foils as catalysts, while the conversion is carried out by a coupled reactor that performs electrochemical reduction of carbon dioxide using ZnO as a catalyst and KHCO3 as an electrolyte. The capture module is optimized such that, powered by a current density of 100 mA/cm2, from a mixture of the CO2−N2 gas stream, a pure and stable CO2 outlet flow of 4−5 mL/min is obtained. The conversion module is able to convert the carbon dioxide into a mixture of gaseous CO and H2 (syngas) with a selectivity for the carbon monoxide of 56%. This represents the first all-electrochemical system for carbon dioxide capture and conversion.

This Editorial provides an overview of the 13 papers published in the Special Issue Environmental and Energetic Valorization of RenewableResources belonging to Section B: Sustainable Energy of the Energies journal, five being review papers and the remaining being scientific articles.

Plastic waste generation has increased dramatically every day. Indiscriminate disposal of plastic wastes can lead to several negative impacts on the environment, such as a significant increase in greenhouse gas emissions and water pollution. Therefore, it is wise to think of other alternatives to reduce plastic wastes without affecting the environment, including converting them into valuable products using effective methods such as pyrolysis. Products from the pyrolysis process encompassing of liquid, gas, and solid residues (char) can be turned into beneficial products, as the liquid product can be used as a commercial fuel and char can function as an excellent adsorbent. The char produced from plastic wastes could be modified to enhance carbon dioxide (CO2) adsorption performance. Therefore, this review attempts to compile relevant knowledge on the potential of adsorbents derived from waste plastic to capture CO2. This review was performed in accordance with PRISMA guidelines. The pl... [more]

Capture conditions for CO2 vary substantially between industrial point sources. Depending on CO2 fraction and pressure level, different capture technologies will be required for cost- and energy-efficient decarbonisation. For decarbonisation of shifted synthesis gas from coal gasification, several studies have identified low-temperature CO2 capture by condensation and phase separation as an energy- and cost-efficient option. In the present work, a process design is proposed for low-temperature CO2 capture from an Integrated Gasification Combined Cycle (IGCC) power plant. Steady-state simulations were carried out and the performance of the overall process, as well as major process components, were investigated. For the baseline capture unit layout, delivering high-pressure CO2 at 150 bar, the net specific power requirement was estimated to 273 kJe/kgCO2, and an 85% CO2 capture ratio was obtained. The impact of 12 different process parameters was studied in a sensitivity analysis, the re... [more]

The performance of a plate heat exchanger (PHE), in comparison with the conventional shell and tube types, through a trade-off analysis of energy cost and capital cost resulting from different temperature approaches in the cross-exchanger of a solvent-based CO2 capture process, was evaluated. The aim was to examine the cost reduction and CO2 emission reduction potentials of the different heat exchangers. Each specific heat exchanger type was assumed for the cross-exchanger, the lean amine cooler and the cooler to cool the direct contact cooler’s circulation water. The study was conducted for flue gases from a natural-gas combined-cycle power plant and the Brevik cement plant in Norway. The standard and the lean vapour compression CO2 absorption configurations were used for the study. The PHE outperformed the fixed tube sheet shell and tube heat exchanger (FTS-STHX) and the other STHXs economically and in emissions reduction. The optimal minimum temperature approach for the PHE cases ba... [more]

The increasing demand for energy and commodities has led to escalating greenhouse gas emissions, the chief of which is represented by carbon dioxide (CO2). Blue hydrogen (H2), a low-carbon hydrogen produced from natural gas with carbon capture technologies applied, has been suggested as a possible alternative to fossil fuels in processes with hard-to-abate emission sources, including refining, chemical, petrochemical and transport sectors. Due to the recent international directives aimed to combat climate change, even existing hydrogen plants should be retrofitted with carbon capture units. To optimize the process economics of such retrofit, it has been proposed to remove CO2 from the pressure swing adsorption (PSA) tail gas to exploit the relatively high CO2 concentration. This study aimed to design and numerically investigate a vacuum pressure swing adsorption (VPSA) process capable of capturing CO2 from the PSA tail gas of an industrial steam methane reforming (SMR)-based hydrogen p... [more]

Lowering the regeneration temperature for solid CO2-capture materials is one of the critical tasks for economizing CO2-capturing processes. Based on reported pKa values and nucleophilicity, we compared two different polyethylenimines (PEIs): branched PEI (BPEI) and linear PEI (LPEI). LPEI outperformed BPEI in terms of adsorption and desorption properties. Because LPEI is a solid below 73−75 °C, even a high loading amount of LPEI can effectively adsorb CO2 without diffusive barriers. Temperature-programmed desorption (TPD) demonstrated that the desorption peak top dropped to 50.8 °C for LPEI, compared to 78.0 °C for BPEI. We also revisited the classical adsorption model of CO2 on secondary amines by using in situ modulation excitation IR spectroscopy, and proposed a new adsorption configuration, R1(R2)-NCOOH. Even though LPEI is more expensive than BPEI, considering the long-term operation of a CO2-capturing system, the low regeneration temperature makes LPEI attractive for industrial a... [more]

The removal of acidic gases and impurities from gas mixtures is a critical operation in the oil and gas industry. Several separation techniques, e.g., cryogenic fractionation, polymeric membranes, zeolites, and metal−organic frameworks, are employed to treat gas mixtures depending upon the nature of separation and contaminants present in the gas mixtures. However, removing N2, H2, H2S, and CO2 contents from industrial gas mixtures is a challenging step due to economic factors, high energy consumption, and effective separation. Hydrate-based separation for selective gas removal is a promising and efficient separation technique over a range of temperatures, pressures, and acidic gas contents. The enclathration of CO2, H2, N2, H2S, and other natural gas constituents effectively removes acidic gases and other contaminants from process gas streams. This work presents a novel process design to remove acidic gases and other contaminants from industrial waste gases and natural gas mixtures to... [more]

In order to obtain the cheap waste calcium-based sorbent, three wasted CaCO3 precursors, namely carbide slag, chicken eggshells, and analytical reagent-grade calcium carbonate, were selected and prepared at 700 °C to form calcium-based sorbents for CO2 capture. TGA was used to test the CO2 uptake performance of each calcium-based sorbent in 20 cycles. To identify the decay mechanism of CO2 uptake with an increasing number of cycles, all calcium-based sorbents were characterized by using XRF, XRD, and N2 adsorption. The specific surface area of calcium-based sorbents was used to redefine the formula of cyclic carbonation reactivity decay. The carbonation conversion rate of three calcium-based sorbents exhibited a decreasing trend as the cycle number increased. Chicken eggshells exhibited the most significant decrease rate (over 50% compared with Cycle 1), while carbide slag and analytical reagent-grade calcium carbonate showed a flat linear decline trend. The specific surface area of th... [more]

The rise of carbon dioxide (CO2) levels in the atmosphere emphasises the need for improving the current carbon capture and storage (CCS) technology. A conventional absorption method that utilises amine-based solvent is known to cause corrosion to process equipment. The solvent is easily degraded and has high energy requirement for regeneration. Amino acids are suitable candidates to replace traditional alkanolamines attributed to their identical amino functional group. In addition, amino acid salt is a green material due to its extremely low toxicity, low volatility, less corrosive, and high efficiency to capture CO2. Previous studies have shown promising results in CO2 capture using amino acids salts solutions and amino acid ionic liquids. Currently, amino acid solvents are also utilised to enhance the adsorption capacity of solid sorbents. This systematic review is the first to summarise the currently available amino acid-based adsorbents for CO2 capture using PRISMA method. Physical... [more]

Hydrogen is a versatile vector for heat and power, mobility, and stationary applications. Steam methane reforming and coal gasification have been, until now, the main technologies for H2 production, and in the shorter term may remain due to the current costs of green H2. To minimize the carbon footprint of these technologies, the capture of CO2 emitted is a priority. The in situ capture of CO2 during the reforming and gasification processes, or even during the syngas upgrade by water−gas shift (WGS) reaction, is especially profitable since it contributes to an additional production of H2. This includes biomass gasification processes, where CO2 capture can also contribute to negative emissions. In the sorption-enhanced processes, the WGS reaction and the CO2 capture occur simultaneously, the selection of suitable CO2 sorbents, i.e., with high activity and stability, being a crucial aspect for their success. This review identifies and describes the solid sorbents with more potential for... [more]

To achieve net-zero iron and steel production by 2050, many iron and steel producers are turning to direct reduced iron (DRI)—electric arc furnace (EAF) steel production as an opportunity to achieve significant CO2 emissions reductions relative to current levels. However, additional innovations are required to close the gap between DRI and net-zero steel. Pressurized chemical looping-DRI (PCL-DRI) is a novel technology explored to meet this target, in which the reformer firebox and fired process gas heaters are replaced with PCL combustion units. Captured CO2 is conditioned and compressed for pipeline transportation and storage/utilization. The performance of two different PCL-DRI configurations relative to traditional DRI processes was explored via process simulation: a Midrex-type process and an Energiron-type process. The PCL-DRI processes were shown to have equivalent or lesser total fuel consumption (8% reduction) compared to the base cases, and greater process water production (1... [more]

Carbon dioxide (CO2) has reached a higher level of emissions in the last decades, and as it is widely known, CO2 is responsible for numerous environmental problems, such as climate change. Thus, there is a great need for the application of CO2 capture and storage, as well as of CO2 utilization technologies (CCUS). This review article focuses on summarizing the current CCUS state-of-the-art methods used in Europe. Special emphasis has been given to mineralization methods/technologies, especially in basalts and sandstones, which are considered to be suitable for CO2 mineralization. Furthermore, a questionnaire survey was also carried out in order to investigate how informed about CO2 issues European citizens are, as well as whether their background is relative to their positive or negative opinion about the establishment of CCUS technologies in their countries. In addition, social acceptance by the community requires contact with citizens and stakeholders, as well as ensuring mutual trus... [more]

Global warming, along with increasing global energy demands, has led to the need for a sustainable and low-carbon-based energy economy. In addition to renewable energy technologies, such as biomass, solar, hydro, and wind, another possible strategy to mitigate climate change is the capture/conversion and recycling of CO2. In recent years, many methods for both CO2 capture (mainly adsorption, absorption, and membrane) and conversion (many electrolysis, catalyst, and plasma) have been investigated. Conversion technology is less studied but seems to be very promising. Within that, non-thermal plasma technology has received much interest because it works at low temperatures and atmospheric pressure, and there is no need for high temperature and high electricity consumption, which are typical of the catalyst and electrolysis conversion processes, respectively. Therefore, in order to optimize this emerging technology, simulative kinetic models have been developed with the aim of maximizing b... [more]