The use of Fabric-Reinforced Cementitious Matrix (FRCM) systems as externally bonded reinforcement for concrete or masonry structures is, nowadays, a common practice in civil engineering. However, FRCM durability against aggressive environmental conditions is still an open issue. In this paper, the mechanical behavior of a glass FRCM system, after being subjected to saline, alkaline and freeze−thaw cycles, has been investigated. The experimental campaign includes tensile tests on the fabric yarns, compression and flexural tests on the matrix and tensile tests (according to AC434) on FRCM prismatic coupons. The effects of the different environmental exposures on the mechanical properties of both the constituent materials and the composite system have been investigated and discussed. Ion chromatography analysis has also been performed to better understand the damage mechanisms induced by environmental exposures and to evaluate the ions’ penetration within the inorganic matrix. Alkaline e... [more]

Since the discovery of graphene, there has been increasing interest in two-dimensional (2D) materials. To realize practical applications of 2D materials, it is essential to isolate mono- or few-layered 2D nanosheets from unexfoliated counterparts. Liquid phase exfoliation (LPE) is the most common technique to produce atomically thin-layered 2D nanosheets. However, low production yield and prolonged process time remain key challenges. Recently, novel exfoliation processes based on microfluidics have been developed to achieve rapid and high yield production of few-layer 2D nanosheets. We review the primary types of microfluidic-based exfoliation techniques in terms of the underlying process mechanisms and the applications of the 2D nanosheets thus produced. The key challenges and future directions are discussed in the above context to delineate future research directions in this exciting area of materials processing.

The newest generation of lubricants needs to adapt to stricter environmental policies. Simple and sustainable formulations with tunable rheological properties under the action of electric potentials may be the key. The present research explored the feasibility of producing electro-sensitive ecolubricants based on nanocellulose (crystalline and fibrillar) or nanoclay (Cloisite 15A montmorillonite and halloysite nanotubes) dispersions in castor oil, at concentrations that ranged from 2 to 6 wt.%. Broadband dielectric spectroscopy (BDS) measurements allowed for a first estimate on the electro-responsive potential of the nanofluids. The nanocelluloses and the montmorillonite suspensions presented a relaxation event in the dielectric loss, ε″, centered at ca. 2−4 kHz, which is related to interfacial polarization. Moreover, their actual electro-rheological (ER) effect under high electric potentials up to 4 kV/mm was assessed by determining the magnitude of the yield stress from steady flow c... [more]

A doped polymer nanoparticle (dPNP) of electrochemiluminescence (ECL) was prepared via doping the anionic polyelectrolyte polyacrylic acid (PAA) and the cationic polymer poly-ethyleneimine (PEI) into the polymer nanoparticle (PNP), which was self-assembled by Ru(bpy)32+ derivative-grafted PAA (PAA−Ru) with both cations and anions. The good electrical conductivity of the doped polyelectrolyte PAA enhanced the ECL intensity of PNP to 109.1%, and the involvement of a large number of tertiary amine groups of the doped PEI further enhanced that to 127.3%; meanwhile, doping low-molecular-weight PEI into PNP, while simultaneously doping high-molecular-weight PAA, avoided the precipitation of PAA and PEI, due to interaction of the two oppositely charged polymers; and these also made the self-assembly procedure more effective and the nanoparticle structure more stable than PNP and also led to the production of rich residual PAA chains on the surface of dPNP. The storage results showed that the... [more]

This paper reports the results of an experimental investigation on the mechanical properties of geopolymer foams incorporating filler from the coke dust waste (CDW). In this work, CDW was used to replace a part of geopolymer paste at 5%, 10%, 20%, and 30% by geopolymer binder mass. The physico-mechanical properties and thermal resistance against high temperatures of CDW/geopolymer foams are presented. The primary results obtained show that the use of CDW in the production of geopolymer foam composites made it possible for them to achieve relatively good mechanical properties. However, the incorporation of the CDW into the geopolymer had a slightly negative effect on thermal conductivity, but significantly improved the mechanical strength of the final product. Moreover, this waste also helped the composite foam to achieve a structure with more uniform open pores distribution, compared to the pure foam. After exposure to elevated temperatures, the residual strength of the composite foams... [more]

An increase of environmental awareness recently has increased the interest of researchers in using of biopolymer-based films. The films have been prepared extensively by utilizing starch, carboxymethyl cellulose, chitosan, protein, gelatin, carrageenan, alginate, pectin, guar gum and pullulan. They are typically modified with surface-active agents (surfactants) such as glycerol monostearate, sucrose ester, sodium stearoyl lactate, sodium dodecyl sulfate, ethyl lauroyl arginate HCl, Span 20 to 80, Tween-20 to 80 and soy lecithin for improving the functional properties of the films. In this brief review, two types of biopolymer-based films that prepared through casting method were categorized, specifically solution- and emulsion-based films. The four types of surfactants, namely non-ionic, anionic, cationic and amphoteric surfactants that are regularly used to modify biopolymer-based films are also described. The functional properties of the films modified with different types of surfact... [more]

The influence of post-processing conditions on the magnetic properties of amorphous and nanocrystalline microwires has been thoroughly analyzed, paying attention to the influence of magnetoelastic, induced and magnetocrystalline anisotropies on the hysteresis loops of Fe-, Ni-, and Co-rich microwires. We showed that magnetic properties of glass-coated microwires can be tuned by the selection of appropriate chemical composition and geometry in as-prepared state or further considerably modified by appropriate post-processing, which consists of either annealing or glass-coated removal. Furthermore, stress-annealing or Joule heating can further effectively modify the magnetic properties of amorphous magnetic microwires owing to induced magnetic anisotropy. Devitrification of microwires can be useful for either magnetic softening or magnetic hardening of the microwires. Depending on the chemical composition of the metallic nucleus and on structural features (grain size, precipitating phases... [more]

Ceramic matrix composites reinforced with carbon nanotubes are becoming increasingly popular in industry due to their astonishing mechanical properties and taking into account the fact that advanced production technologies make carbon nanotubes increasingly affordable. In the present paper, the most convenient contemporary methods used for the compaction of molding masses composed of either technical ceramics or ceramic matrix composites reinforced with carbon nanotubes are surveyed. This stage that precedes debinding and sintering plays the key role in getting pore-free equal-density ceramics at the scale of mass production. The methods include: compaction in sealed and collector molds, cold isostatic and quasi-isostatic compaction; dynamic compaction methods, such as magnetic pulse, vibration, and ultrasonic compaction; extrusion, stamping, and injection; casting from aqueous and non-aqueous slips; tape and gel casting. Capabilities of mold-free approaches to produce precisely shaped... [more]

Nuclear magnetic resonance (NMR) approaches have unique advantages in the analysis of crude oil because they are non-destructive and provide information on chemical functional groups. Nevertheless, the correctness and effectiveness of NMR techniques for determining saturates, aromatics, resins, and asphaltenes (SARA analysis) without oil fractioning are still not clear. In this work we compared the measurements and analysis of high-resolution 13C NMR spectra in B0 ≈ 16.5 T (NMR frequency of 175 MHz) with the results of SARA fractioning for four various heavy oil samples with viscosities ranging from 100 to 50,000 mPa·s. The presence of all major hydrocarbon components both in crude oil and in each of its fractions was established quantitatively using NMR spectroscopy. Contribution of SARA fractions in the aliphatic (10−60 ppm) and aromatic (110−160 ppm) areas of the 13C NMR spectra were identified. Quantitative fractions of aromatic molecules and oil functional groups were determined.... [more]

Water pollution is one of the major challenges facing modern society because of industrial development and urban growth. This study is directed towards assessing the use of multiwall carbon nanotube, after derivatization and magnetization, as a new and renewable absorbent, to remove toxic metal ions from waste streams. The adsorbents were prepared by, first oxidation of multiwall carbon nanotube, then derivatizing the oxidized product with hydroxyl amine, hydrazine and amino acid. The adsorbents were characterized by various techniques. The adsorption efficiency of the multiwall carbon nanotube adsorbents toward Pb(II) was investigated. The effect of adsorbent’s dose, temperature, pH, and time on the adsorption efficiency were studied and the adsorption parameters that gave the highest efficiency were determined. The derivatives have unique coordination sites that included amine, hydroxyl, and carboxyl groups, which are excellent chelating agents for metal ions. The thermodynamic and k... [more]

The technology of using metallic iron (Fe0) for in situ generation of iron oxides for water treatment is a very old one. The Fe0 remediation technology has been re-discovered in the framework of groundwater remediation using permeable reactive barriers (PRBs). Despite its simplicity, the improvement of Fe0 PRBs is fraught with difficulties regarding their operating modes. The literature dealing with Fe0 remediation contains ambiguities regarding its invention and its development. The present paper examines the sequence of contributions prior to the advent of Fe0 PRBs in order to clarify the seemingly complex picture. To achieve this, the current paper addresses the following questions: (i) What were the motivations of various authors in developing their respective innovations over the years?, (ii) what are the ancient achievements which can accelerate progress in knowledge for the development of Fe0 PRBs?, and (iii) was Fe0 really used for the removal of organic species for the first t... [more]

Hydrogen cyanide (HCN)-derived polymers have been recognized as sources of relevant organic molecules in prebiotic chemistry and material sciences. However, there are considerable gaps in the knowledge regarding the polymeric nature, the physicochemical properties, and the chemical pathways along polymer synthesis. HCN might have played an important role in prebiotic hydrothermal environments; however, only few experiments use cyanide species considering hydrothermal conditions. In this work, we synthesized an HCN-derived thermal polymer simulating an alkaline hydrothermal environment (i.e., HCN (l) 0.15 M, 50 h, 100 °C, pH approximately 10) and characterized its chemical structure, thermal behavior, and the hydrolysis effect. Elemental analysis and infrared spectroscopy suggest an important oxidation degree. The thermal behavior indicates that the polymer is more stable compared to other HCN-derived polymers. The mass spectrometric thermal analysis showed the gradual release of severa... [more]

As-synthesized oleic amido propyl betaine surfactant mixture was developed through a slight modification of a conventional two-step betaine synthesis process of amidation and quaternization reactions. This method is a “direct formulating through synthesis” to achieve a targeted interfacial property (interfacial tension or IFT) of the as-synthesized surfactant. Oil−water IFT was measured in the crude oil−seawater system at 96 °C. The result showed that the as-synthesized surfactant was able to reduce crude oil−seawater IFT to the ultra-low level (<0.01 mN/m). As the finding emerged, the investigation was conducted to identify the elements that would bring the characteristic of ultra-low IFT. The characterization of the surfactant using FTIR, TG-IR, and HPLC suggested that unreacted materials associated with the surfactant remained, such as the carryover of a fatty amide from the intermediate process, residues of N, N trimethylene dimethylamine and sodium chloride as a by-product, and... [more]

Stretchable and flexible graphite films can be effectively applied as functional layers in the progressively increasing field of stretchable and flexible electronics. In this paper, we focus on the feasibility of making stretchable and flexible films based on expanded graphite particles on a polymeric substrate material, polydimethylsiloxane (PDMS). The expanded graphite particles used in this work are prepared by utilizing bath sonication processes at the ultrasonic frequency of either the commercially available graphite flakes or graphite particles obtained through electrolysis under the interstitial substitution of silver and sulfate, respectively. The X-ray diffraction (XRD) patterns confirm that, due to the action of the bath sonication intercalation of graphite taking place, the resistances of the as-fabricated thin films is ultimately lowered. Mechanical characterizations, such as stretchability, flexibility and reliability tests were performed using home-made tools. The films w... [more]

Manufacturing-based carbon fibre-reinforced polymer (CFRP) and glass fibre-reinforced polymer (GFRP) wastes (pre-consumer waste) were recycled to recover valuable carbon fibres (CFs) and glass fibres (GFs), utilising a novel thermal recycling process with a cone calorimeter setup. The ideal conditions to recycle both the fibres occurred at 550 °C in atmospheric pressure. The processing time in the batch reactor to recycle CFs was 20−25 min, and to recycle GFs it was 25−30 min. The recovery rate of the recycled CFs was 95−98 wt%, and for GFs it was 80−82 wt%. Both the recycled fibres possessed a 100−110 mm average length. The resin phase elimination was verified by employing scanning electron microscopy (SEM). Furthermore, the fibres were manually realigned, compression moulded at room temperature, and cured for 24 h by a laminating epoxy resin system. The newly manufactured CFRP and GFRP composites were continuous (uniform length from end to end), unidirectionally oriented (0°), and no... [more]

Three 40 wt % Pt/C electrocatalysts prepared using two different approaches—the polyol process and electrochemical dispersion of platinum under pulse alternating current—and a commercial Pt/C catalyst (Johnson Matthey prod.) were examined via X-ray diffraction (XRD) and transmission electron microscopy (TEM). The stability characteristics of the Pt/C catalysts were studied via long-term cycling, revealing that, for all cycling modes, the best stability was achieved for the Pt/C catalyst with the largest platinum nanoparticle sizes, which was synthesized via electrochemical dispersion of platinum under pulse alternating current. Our results show that the mass and specific electrocatalytic activities of Pt/C catalysts toward ethanol electrooxidation are determined by the value of the electrochemically active Pt surface area in the catalysts.

Currently, the use of sustainable chemistry as an ecological alternative for the generation of products or processes that are free of a polluting substance has assumed a preponderant role. The aim of this work is to propose a bioinspired, facile, low cost, non-toxic, and environmentally friendly alternative to obtaining magnetic nanoparticles with a majority phase of magnetite (Fe3O4). It is important to emphasize that the synthesis was based on the chemical reduction through the Cnicus benedictus extract, whose use as reducing agent has not been reported in the synthesis of iron oxides nanoparticles. In addition, the Cnicus benedictus is an abundant endemic plant in Mexico with several medicinal properties and a large number of natural antioxidants. The obtained nanoparticles exhibited significant magnetic and antibacterial properties and an enhanced photocatalytic activity. The crystallite size of the Fe3O4 nanoparticles (Fe3O4 NP’s) was calculated by the Williamson-Hall method. The... [more]

Upgrading raw biogas to methane (CH4) is a vital prerequisite for the utilization of biogas as a vehicle fuel or the similar field as well. In this work, biogas yield from the anaerobic fermentation of food waste containing methane (CH4, 60.4%), carbon dioxide (CO2, 29.1%), hydrogen sulfide (H2S, 1.5%), nitrogen (N2, 7.35%) and oxygen (O2, 1.6%) was upgraded by dynamic adsorption. The hydrogen sulfide was removed from the biogas in advance by iron oxide (Fe2O3) because of its corrosion of the equipment. Commercial 13X zeolite and carbon molecular sieve (CMS) were used to remove the other impurity gases from wet or dry biogas. It was found that neither 13X zeolite nor CMS could effectively remove each of the impurities in the wet biogas for the effect of water vapor. However, 13X zeolite could effectively remove CO2 after the biogas was dried with silica and showed a CO2 adsorption capacity of 78 mg/g at the condition of 0.2 MPa and 25 °C. Additionally, 13X zeolite almost did not adsorb... [more]

This study reports the effect of high-temperature treatment on the electrical properties of charcoal, coal, and coke. The electrical resistivity of industrial charcoal samples used as a reducing agent in electric arc furnaces was investigated as a renewable carbon source. A set-up to measure the electrical resistivity of bulk material at heat treatment temperatures up to 1700 ∘C was developed. Results were also evaluated at room temperature by a four-point probe set-up with adjustable load. It is shown that the electrical resistivity of charcoal decreases with increasing heat treatment temperature and approaches the resistivity of fossil carbon materials at temperatures greater than 1400 ∘C. The heat treatment temperature of carbon material is the main influencing parameter, whereas the measurement temperature and residence time showed only a minor effect on electrical resistivity. Bulk density of the carbon material and load on the burden have a large impact on the electrical resistiv... [more]

A single polymer flooding is a widely employed enhanced oil recovery method, despite polymer vulnerability to shear and thermal degradation. Nanohybrids, on the other hand, resist degradation and maintain superior rheological properties at different shear rates. In this article, the effect of coupling CuO nanoparticles (NPs) and nanoclay with partially hydrolyzed polyacrylamide (HPAM) polymer solution on the rheological properties and the recovery factor of the nanohybrid fluid was assessed. The results confirmed that the NP agents preserved the polymer chains from degradation under mechanical, chemical (i.e., salinity), and thermal stresses and maintained good extent of entanglement among the polymer chains, leading to a strong viscoelastic attribute, in addition to the pseudoplastic behavior. The NP additives increased the viscosity of the HPAM polymer at shear rates varying from 10−100 s−1. The rheological properties of the nanohybrid systems varied with the NP additive content, whi... [more]

Heterogeneous catalysts are widely used in the chemical industry. Compared with homogeneous catalysts, they can be easily separated from the reaction mixture. To design and optimize an efficient and safe chemical process one needs to calculate the energy balance, implying the need for knowledge of the catalyst’s specific heat capacity. Such values are typically not reported in the literature, especially not the temperature dependence. To fill this gap in knowledge, the specific heat capacities of commonly utilized heterogeneous catalytic supports were measured at different temperatures in a Tian−Calvet calorimeter. The following materials were tested: activated carbon, aluminum oxide, amberlite IR120 (H-form), H-Beta-25, H-Beta-38, H-Y-60, H-ZSM-5-23, H-ZSM-5-280, silicon dioxide, titanium dioxide, and zeolite 13X. Polynomial expressions were successfully fitted to the experimental data.

This study investigated influences of the open/close states of pores and porosity distribution of activated coke on the mechanical strength of common activated coke for the purification of coal-fired flue gas by analyzing pore structure, abrasive resistance, and compression strengths of 9 types of desulfurization and denitration activated cokes. Research conclusions are conducive to disclosing the influences of porosity characteristics of activated coke for the purification of coal-fired flue gas on mechanical strength, decreasing the physical consumption of activated coke in the recycling of flue gas purification systems, and lowering the purification cost of coal-fired flue gas. According to research results, pores in the ranges of 0−2 nm and 2−500 nm of activated coke are further developed after recycling using the coal-fired flue gas purification system, and the average compression strength of activated coke is about 70% of the added fresh activated coke. However, the abrasive resi... [more]

The mesoporous silica wall materials can achieve controlled load and sustained-release of active agents. An antimicrobial nanoscale silica microcapsule containing cinnamaldehyde (CA) was prepared by the sol-gel method and applied in poly (butyleneadipate-co-terephthalate) (PBAT) film. The surface morphology, physical and chemical properties, and antibacterial properties of microcapsules and films were studied. The effects of different temperatures and humidities on the release behavior of microcapsules were also evaluated. Results showed that CA was successfully encapsulated in silica microcapsule which had a diameter of 450−700 nm. The antibacterial CA agent had a long-lasting release time under lower temperature and relative humidity (RH) environment. At low temperature (4 °C), the microcapsules released CA 32.35% in the first 18 h, and then slowly released to 56.08% in 216 h; however, the microcapsules released more than 70% in 18 h at 40 °C. At low humidity (50%RH), the release rat... [more]

Ceria-based mixed oxides have been widely studied in catalysis due to their unique surface and redox properties, with implications in numerous energy- and environmental-related applications. In this regard, the rational design of ceria-based composites by means of advanced synthetic routes has gained particular attention. In the present work, ceria−titania composites were synthesized by four different methods (precipitation, hydrothermal in one and two steps, Stöber) and their effect on the physicochemical characteristics and the CO oxidation performance was investigated. A thorough characterization study, including N2 adsorption-desorption, X-ray diffraction (XRD), scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM/EDS), transmission electron microscopy (TEM) and H2 temperature-programmed reduction (H2-TPR) was performed. Ceria−titania samples prepared by the Stöber method, exhibited the optimum CO oxidation performance, followed by samples prepared by the hyd... [more]

CoO/Co3O4 nanoparticles (NPs) were synthesized by using a fresh egg white-assisted combustion method which acts as a new approach for green synthesis of this composite. This method was carried out by the direct heat of cobalt precursor with egg white at low temperature for very short period. In fact, this route is a novel, cheap and appropriate technique yielding nanoparticle-based materials. CoO/Co3O4 nanoparticles were characterized by examining the structure and identifying the elements and determining the morphology via XRD, FTIR, SEM, EDS and TEM techniques. The sample magnetic observations were measured through the use of a vibrating sample magnetometer (VSM). The results of XRD, EDS, SEM and TEM confirmed the positive synthesis of the cubic CoO/Co3O4 NPs with sponge crystals which proceed. For the as synthesized composite, 57.75 m2/g, 0.0148 cc/g and 10.31 nm were identified to be the SBET, Vp and ȓ, respectively. The cobalt oxide particles in their nature were polycrystalline,... [more]