Pyro-breaker, a fast-responding, highly reliable and explosive-driven circuit breaker, is utilized in several Quench Protection Systems (QPS). The commutation process and its parameters are the main technical considerations in the process of designing a new pyro-breaker. The commutation parameters, such as the commutation time and the current change rate, are not only determined by the electrical parameters of the commutation circuit but also the arc behavior during the operation. The arc behavior is greatly affected by the structure and the driving mechanism of the Commutation Section (CS) in the pyro-breaker. The arc model was developed decades ago and the black-box arc model is considered a valid method to study arc behavior. In this paper, the Schavemaker black-box arc model, an improved Mayr-type arc model, is applied to study the commutation process of a newly designed pyro-breaker. Unlike normal circuit breakers, the arc discussed in this paper is discharged in deionized water.... [more]

Widespread applications of AC motors fed by variable frequency drives in electrified vehicles have become a conventional technical solution. The flexibility of control, low cost, and high energy efficiency attract developers and engineers to apply these appliances in cars, railway trains, trams, etc. The distinctive characteristic of vehicles is a wide range of required rotation speed and torque. This circumstance means that the problems of the AC motor (nominal power, synchronous speed) and gearbox (transmission ratio) become non-trivial and necessitate optimal selection to ensure the best functionality of the entire driving system. This study proposes an approach for the optimal choice of a specific AC motor (nominal rating, synchronous speed) and the transmission ratio of the gearbox by analyzing the entire system’s losses. The optimal selection of an AC motor ensures maximum energy efficiency for a specific transportation driving cycle.

In 2020, residential sector loads reached 25% of the overall electrical consumption in Europe and it is foreseen to stabilise at 29% by 2050. However, this relatively small increase demands, among others, changes in the energy consuming behaviour of households. To achieve this, Demand Response (DR) has been identified as a promising tool for unlocking the hidden flexibility potential of residential consumption. In this work, a holistic incentive-based DR framework aiming towards load shifting is proposed for residential applications. The proposed framework is characterised by several innovative features, mainly the formulation of the optimisation problem, which models user satisfaction and the economic operation of a distributed household portfolio, the customised load forecasting algorithm, which employs an adjusted Gradient Boosting Tree methodology with enhanced feature extraction and, finally, a disaggregation tool, which considers electrical features and time of use information. T... [more]

The article describes an assessment of possible changes in constant fatigue life of a medium flow-coefficient centrifugal compressor impeller subject to operation at close-to-surge point. Some aspects of duct acoustics are additionally analyzed. The experimental measurements at partial load are presented and are primarily used for validation of unidirectionally coupled fluid-structural numerical model. The model is based on unsteady finite-volume fluid-flow simulations and on finite-element transient structural analysis. The validation is followed by the model implementation to replicate the industry-scale loads with reasonably higher rotational speed and suction pressure. The approach demonstrates satisfactory accuracy in prediction of stage performance and unsteady flow field in vaneless diffuser. The latter is deduced from signal analysis relying on continuous wavelet transformations. On the other hand, it is found that the aerodynamic incidence losses at close-to-surge point are un... [more]

The performance of a conventional Class-E2-based WPT system is sensitive to system parameters such as the coil coupling coefficient and load variation. System efficiency decreases rapidly when the coil coupling coefficient and load deviate from their optimum values. In this paper, an impedance matching method and a design procedure are proposed to maintain high system efficiency over a wider range of coupling coefficient and load variations. The load-pull technique is adopted to identify the high-efficiency load region of a Class-E power amplifier (PA), and a double-L-type impedance matching network (IMN) is proposed to transform the load impedance of a Class-E PA into a high-efficiency working region. Compared to a single L-type IMN, a double-L-type IMN is more flexible and has better tuning performance. A 6.78 MHz Class-E2-based WPT system was built to validate the proposed design method. The experimental results show that the proposed double-L-type IMN can significantly attenuate th... [more]

Different methods to achieve zero-energy and low carbon on the scale of a building are shown by most of the research works. Despite this, the recommendations generally offered by researchers do not always correspond to the realities found during the construction of new buildings in a determined region. Therefore, a standard may not be valid in all climate regions of the world. Being aware of this fact, a study was carried out to analyse the design of new buildings respecting the “zero-energy and low carbon emission” concept in tropical climatic regions when they are compared with a base case of temperate regions. To reach this objective, the comparison between real and simulated data from the different buildings studied was developed. The results showed that the renovation of existing residential buildings allows for reducing up to 35% of energy demand and a great quantity of CO2 emissions in both climate types. Despite this, the investment rate linked to the construction of zero-energ... [more]

The printed circuit heat exchanger (PCHE) is a promising waste heat recovery technology to improve energy efficiency. The current investigation presents the experimental results on the thermal performance of a novel PCHE for low-temperature waste heat recovery. The novel PCHE was manufactured using precision machining and diffusion bonding. The thermal performances, such as effectiveness and NTU values at different temperatures, are evaluated, and water is used as a working fluid. The experimental results indicate that the PCHE’s effectiveness is around 0.979 for an inlet flow temperature of 95 °C. The predominant factors affecting the thermal performance of the PCHE are the inlet flow temperature and the flow rate of the working fluid. In addition, a comparison of the experimental results and the literature shows that the effectiveness of the PCHE is better than the others, which have fewer layers of PCHE fins.

In rural Nepal, micro-hydropower plant mini-grids provide renewable electricity to thousands of communities but the plants often have poor financial sustainability. Widespread uptake of electric cooking in such communities is currently not feasible due to high peak loads and limited capacity. In this paper, we develop a Remote-Areas Multi-Energy Systems Load Profiles (RAMP)-based stochastic techno-economic model for evaluating the economic viability of off-grid communities and improving their financial sustainability by introducing new appliances, productive end uses, and demand-side management measures. The model can be used to understand community electricity demand, assess economic status, determine equitable and profitable tariff structures, and plan new connections including electric cooking promotion or new industrial machines. Detailed electric cooking load modelling functionality was developed to represent Nepali cooking practices, scalable to approximate widespread uptake of e... [more]

Sewage sludge (SS) generation and its management still pose a problem in many countries. Anaerobic co-digestion (AcD) of SS with grease trap sludge (GTS) and organic fraction of municipal sewage waste (OFMSW), which are two easily biodegradable substrates, may improve biogas production and AcD kinetics. Algae biomass (AB) of the species Undaria pinnatifida can be the third co-digestion component that may also affect the AcD performance. The aim of the study was therefore to evaluate the performance of mesophilic and thermophilic SS batch AcD with OFMSW, GTS as well as AB through biochemical methane potential (BMP) assay in relation to cumulative specific biogas (YB) and methane yields (Ym). Three kinetic models were applied within the scope of the kinetic study. Results of the study showed that the mixture containing SS, GTS and AB brought the most noticeable improvements in Ym compared to other studied mixtures and in respect to standalone SS digestion, the improvement amounted to 88.... [more]

In the biogas industry, feedstock plans are used to estimate methane production and nutrient content in the digestate, however, these predictions do not consider the mineralized nitrogen fraction of the feedstock, which is useful when determining the quality of the digestate. In this study, the artificial fiber bag technique, which is commonly used to study feedstock degradation in ruminants, was implemented in anaerobic digestion to quantify mineralization of N and S. The artificial fiber bags were used to enclose substrates but with access to inoculum because of small pores in the bags, thereby enabling digestion. The content of the bags was analyzed before and after digestion to quantify residual mass as well as N and S concentration in the substrate. The method was validated through batch anaerobic digestion of a single substrate with and without bags, where the bags showed little influence on methane production and degradation. Semi-continuous anaerobic digestion experiments showe... [more]

High altitude airships possess tremendous potential for long-endurance spot hovering platforms for both commercial and strategic applications. The energy system, which is mainly made up of solar array and regenerative fuel cell, is the key component of a high altitude airship. The thermal effect is a major factor that affects the performance of the energy system of long endurance stratospheric vehicles. In this paper, a conceptual design method focusing on the thermal and power characteristics of an energy system for stratospheric airships is proposed. The effect of thermal behavior of solar array on the energy system is analyzed. An optimized case is obtained on the consideration of power supply, thermal behaviors of helium and solar array. Results show that the maximum temperature difference of the solar array may be reduced by about 20 K and the mass of payload can be improved by up to 5%.

Atmospheric factors, such as clouds, wind, dust, or aerosols, play an important role in the power generation of photovoltaic (PV) plants. Among these factors, soiling has been revealed as one of the most relevant causes diminishing the PV yield, mainly in arid zones or deserts. The effect of soiling on the PV performance can be analyzed by means of I−V curves measured simultaneously on two PV panels: one soiled and the other clean. To this end, two I−V tracers, or one I−V tracer along with a multiplexer, are needed. Unfortunately, these options are usually expensive, and only one I−V tracer is typically available at the site of interest. In this work, the design of a low-cost multiplexer is described. The multiplexer is controlled by a low-cost single-board microcontroller manufactured by ArduinoTM, and is capable of managing several pairs of PV panels almost simultaneously. The multiplexer can be installed outdoors, in contrast to many commercial I−V tracers or multiplexers. This adva... [more]

To explain the effect of tip leakage flow on the performance of an axial-flow transonic compressor, the compressors with different rotor tip clearances were studied numerically. The results show that as the rotor tip clearance increases, the leakage flow intensity is increased, the shock wave position is moved backward, and the interaction between the tip leakage vortex and shock wave is intensified, while that between the boundary layer and shock wave is weakened. Most of all, the stall mechanisms of the compressors with varying rotor tip clearances are different. The clearance leakage flow is the main cause of the rotating stall under large rotor tip clearance. However, the stall form for the compressor with half of the designed tip clearance is caused by the joint action of the rotor tip stall caused by the leakage flow spillage at the blade leading edge and the whole blade span stall caused by the separation of the boundary layer of the rotor and the stator passage. Within the inve... [more]

Currently, there are few studies on the influence of microscale thermal radiation on the equivalent thermal conductivity of microscale porous metal. Therefore, this paper calculated the equivalent thermal conductivity of high-porosity periodic cubic silver frame structures with cell size from 100 nm to 100 µm by using the microscale radiation method. Then, the media radiation characteristics, absorptivity, reflectivity and transmissivity were discussed to explain the phenomenon of the radiative thermal conductivity changes. Furthermore, combined with spectral radiation properties at the different cross-sections and wavelength, the radiative transmission mechanism inside high-porosity periodic cubic frame silver structures was obtained. The results showed that the smaller the cell size, the greater radiative contribution in total equivalent thermal conductivity. Periodic cubic silver frames fluctuate more in the visible band and have better thermal radiation modulation properties in the... [more]

Transportation electrification has kept pushing low-voltage inverter-fed electrical machines to reach a higher power density while guaranteeing appropriate reliability levels. Methods commonly adopted to boost power density (i.e., higher current density, faster switching frequency for high speed, and higher DC link voltage) will unavoidably increase the stress to the insulation system which leads to a decrease in reliability. Thus, a trade-off is required between power density and reliability during the machine design. Currently, it is a challenging task to evaluate reliability during the design stage and the over-engineering approach is applied. To solve this problem, physics of failure (POF) is introduced and its feasibility for electrical machine (EM) design is discussed through reviewing past work on insulation investigation. Then the special focus is given to partial discharge (PD) whose occurrence means the end-of-life of low-voltage EMs. The PD-free design methodology based on u... [more]

This paper identifies and explores regulatory issues that may have an impact on the use of flexibility services by distribution utilities to solve grid constraints. This can be done by flexible distributed energy resources which can be instructed, for instance, to reduce export generating capacity or increasing consumption. We want to identify how regulation can better support the development of the future distribution utility in its role as neutral market facilitator, enabling more competition in local flexibility markets and optimal use of resources. A set of questionnaires were designed to capture the insights around important aspects of the regulation of flexibility markets (utilities’ network incentives, network tariff structure, market design for flexibility markets, etc.). These were sent to distribution utilities, energy regulators, energy marketplaces, energy associations and relevant experts from seven jurisdictions. The responses suggest a collective interest in the procurem... [more]

Fractured rock masses below the water table are a problem in underground excavations because of their low strength and high permeability. Nowadays, these negative connotations can be reduced with techniques such as injection of cement, microcement, or resins grouts. These materials increase the rock mass cohesion while reducing the flow of water through the discontinuities. This paper describes the work carried out to design a waterproofing screen for a three-storey underground basement located in a building near the Bilbao estuary (Northern Spain) and with problems of water seepage from the river. First, a survey of the rock mass is carried out. This survey shows the presence of highly fractured zones and the variability of the permeability as functions of the fractures. Subsequently, the effect on permeability caused by the injection of cement grouts and microcement is studied by means of two pilot injection boreholes and eight control boreholes. Finally, a behavioural model is propo... [more]

In this work, an evaluation and quantification of the impact of using mixtures based on supercritical carbon dioxide “s-CO2” (s-CO2/COS, s-CO2/H2S, s-CO2/NH3, s-CO2/SO2) are made as a working fluid in simple and complex recompression Brayton s-CO2 power cycle configurations that have pressure drops in their components. These cycles are coupled with a solar thermal plant with parabolic-trough collector (PTC) technology. The methodology used in the calculation performance is to establish values of the heat recuperator total conductance (UAtotal) between 5 and 25 MW/K. The main conclusion of this work is that the cycle’s efficiency has improved due to using s-CO2 mixtures as working fluid; this is significant compared to the results obtained using the standard fluid (pure s-CO2). Furthermore, a techno-economic analysis is carried out that compares each configuration’s costs using pure s-CO2 and a mixture of s-CO2/COS with a molar fraction (70/30), respectively, as working fluid where rele... [more]

The recent reports from the Intergovernmental Panel on Climate Change (IPCC) urge for the reconceptualization of our design of the urban built environments. However, current efforts to integrate urban environmental assessment into practice in Egypt are proving insufficient. This paper utilises the Ladybug tools simulation plugins to investigate the impact of changing the morphological characteristics of three-block typologies (scattered, linear and courtyard) and their associated parameters to understand their multidimensional relationship with environmental conditions, outdoor thermal comfort and energy use intensity. This study based in Cairo, Egypt, considers 3430 hypothetical geometrical configurations comprising of a variety of design parameters and indicators. The results show a strong correlation between the design parameters and the combined performance of thermal comfort and energy consumption (R2 = 0.84), with urban density having the strongest impact on both thermal comfort... [more]

Nowadays, municipal solid waste (MSW) management is one of the most critical issues. MSW may threaten the environment; however, the concerning high organic fraction content can be useful. This study aimed to compare the suitability of mechanically sorted organic fraction (OF) of MSW and source-segregated biowaste for biofertilizer usage. The compost and the effluents compositions were analyzed. Compost derived from biowaste can be applied to the soil, while, after processing OFMSW, the metal contents are too high. The exceeding limit values were noted, e.g., lead (over 80 mg/kg) and chrome (75 mg/kg). Effluents from biowaste treatment fulfill the national and UE fertilizers’ requirements, considering the heavy metal contents, while effluents from OFMSW treatments exceed the limit values. The biggest exceedings were observed for nickel (over 3 mg/kg) and zinc (over 500 mg/kg). In general, the heavy metal contamination of byproducts from the OFMSW treatment was much higher. At the same t... [more]

The effect of reducing particle size on physical properties, the methane yield and energy flow were investigated through the biochemical methane potential (BMP) experiment of aerobic-anaerobic digestion (AAD) of rice straw (RS). The whole straw was crushed through four sieves of different aperture sizes (1, 3, 5, and 7 mm) to obtain the actual and non-uniform particle size distribution (PSD). The results indicated that the actual particle sizes were normally or logarithmic normally distributed. Reducing particle size could significantly promote the aerobic hydrolysis and acidification process, increase the content of volatile fatty acids (VFAs) from 4408.78 to 6225.15 mg/L and the degradation of volatile solids (VS) from 40.56% to 50.49%. The results of path analysis suggested that particle size reduction played an important role in improving lignocellulosic degradability, which was the main factor affecting methane production with the comprehensive decision of 0.4616. The maximum meth... [more]

This paper presents the results of a multi-disciplinary effort to clarify the state of the art and the state of practice, and necessary future research for creating the seamless integration and application of light in buildings, regardless of source, which is purposely modulated to illuminate surfaces and designed in a way that is comfortable, healthy, pleasing, cost-effective, and energy efficient. The authors unwrap the research, tools, and technical gaps preventing the full integration of electric lighting and daylighting with advanced façades through the coordination of lighting and windows research activities. The study and a stakeholder workshop captured current technology readiness levels (TRL), as well as research thrusts and implementation guidelines, and identified research priorities, presenting an analysis of the current landscape of lighting metrics—and which metrics are in the critical path for developing integrated daylighting and electric lighting systems, and their des... [more]

In order to obtain the full impedance characteristics of a lithium-ion capacitor as a function of temperature, the authors proposed the use of dynamic electrochemical impedance spectroscopy. Impedance tests were carried out under wide range of dynamic temperature changes for lithium-ion supercapacitors. Significant differences in electrochemical processes were observed as a result of working temperature. Moreover, the quality of fitting of the equivalent circuits most frequently used in impedance analysis of lithium-ion capacitors was discussed. The proposed methodology allows for a comprehensive characterization of the performance of these devices and provides key information for their optimization in wide range of operations.

This article presents a proposal for a wireless diagnostic system for checking the air tightness of the ventilation network. The solution is designed to increase crew safety in underground mining plants and increase the energy efficiency of the ventube ventilation system. The system is based on sensors measuring the pressure inside the ventilation duct in relation to the barometric pressure in the immediate vicinity of the duct. The flow of diagnostic data is based on a cascade transfer. The data from the first sensor are transferred successively to the last one. Based on the prior calibration of alarm thresholds in each device, the leakage or factor influencing the increase of air flow resistance is located. The article presents the genesis of the creation and discusses the principle and purpose of the system. In the following chapters, the progress of work related to testing the system in laboratory, industrial, and underground conditions at the Velenje Premogovnik mine (Slovenia) is... [more]

This paper introduces a case study on the failure mechanism and support design of a roadway tunnel in the fault fracture zone of the 106 mining area in the Yuandian no.2 coal mine. Based on the on-site geological conditions (in-situ stress test, borehole television imaging, and lithological analysis), the failure mechanism of the roadway tunnel in the fault fracture zone was studied. The test results showed that the high tectonic stress, fractured rock, and poor lithology are the primary reasons for the roadway instability. According to the support principles of grouting reinforcement, pre-reinforced support, and rational support range, a new type of combined support technology was proposed, including advanced grouting, grouting bolts, and grouting anchor cables. A 100 m roadway section was selected for field testing using the new support scheme, and detailed deformation monitoring was performed. Monitoring results showed that the roadway deformation under the new support was significa... [more]