The European Union aims to reduce Greenhouse Gas (GHG) emissions by 55% before 2030 compared to 1990 as a reference year. One of the main contributions to GHG emissions comes from the household sector. This paper shows that the household sector, when organised into a form of prosumer microgrids, including renewable sources for electric, heating and cooling energy supply, can be efficiently decarbonised. This paper investigates one hypothetical prosumer microgrid with the model RES2GEO (Renewable Energy Sources to Geothermal). The aim is to integrate a carbon-free photovoltaic electricity source and a shallow geothermal reservoir as a heat source and heat sink during the heating and cooling season. A total of four cases have been evaluated for the Zagreb City location. The results represent a balance of both thermal and electric energy flows within the microgrid, as well as thermal recuperation of the reservoir. The levelised cost of energy for all cases, based on a 20-year modelling ho... [more]

Hybrid Renewable Energy Systems (HRES) are an attractive solution for the supply of electricity in remote areas like islands and communities where grid extension is difficult. Hybrid systems combine renewable energy sources with conventional units and battery storage in order to provide energy in an off-grid or on-grid system. The purpose of this study is to examine the techno-economical feasibility and viability of a hybrid system in Donoussa island, Greece, in different scenarios. A techno-economic analysis was conducted for a hybrid renewable energy system in three scenarios with different percentages of adoption rate (20%, 50% and 100%)and with different system configurations. Using HOMER Pro software the optimal system configuration between the feasible configurations of each scenario was selected, based on lowest Net Present Cost (NPC), minimum Excess Electricity percentage, and Levelized Cost of Energy (LCoE). The results obtained by the simulation could offer some operational r... [more]

Wind energy plays a major role in decarbonisation of the electricity sector and supports achieving net-zero greenhouse gas emissions. Over the last decade, the wind energy deployments have grown steadily, accounting for more than one fourth of the annual electricity generation in countries like the United Kingdom, Denmark, and Germany. However, as the share of wind energy increases, system operators face challenges in managing excessive wind generation due to its nondispatchable nature. Currently, the most common practice is wind energy curtailment in which wind farm operators receive constraint payments to reduce their renewable energy production. This practice not only leads to wastage of large volumes of renewable energy, but also the associated financial cost is reflected to rate payers in the form of increased electricity bills. On-site energy storage technologies come to the forefront as a technology option to minimise wind energy curtailment and to harness wind energy in a more... [more]

Production of synthetic natural gas (SNG) offers an alternative way to valorize captured CO2 from energy intensive industrial processes or from a dedicated CO2 grid. This paper presents an energy-efficient way for synthetic natural gas production using captured CO2 and renewable hydrogen. Considering several renewable hydrogen production sources, a techno-economic analysis was performed to find a promising path toward its practical application. In the paper, the five possible renewable hydrogen sources (photo fermentation, dark fermentation, biomass gasification, bio photolysis, and PV electrolysis) were compared to the two reference cases (steam methane reforming and water electrolysis) from an economic stand point using key performance indicators. Possible hydrogen production capacities were also considered for the evaluation. From a technical point of view, the SNG process is an efficient process from both energy efficiency (about 57%) and CO2 conversion rate (99%). From the evaluat... [more]

Photovoltaic (PV) systems encounter substantial losses throughout their lifespan due to the different derating factors of PV modules. Those factors mainly vary according to the geographical location and PV panel characteristics. However, the available literature does not explicitly concentrate on the technical and economic impact of the derating factors within the PV system. Owing to that necessity, this study performs a comprehensive analysis of various PV loss parameters followed by a techno-economic assessment of derating factors using the average value on a grid-connected and optimally tilted PV system located in Hatiya, Bangladesh. Some criteria linked to the derating factors such as PV degradation and ambient temperature are further explored to analyze their impact on the aforementioned power system. Simulation results show that PV power generation would vary around 12% annually, subject to a 10% variation in the derating factor. Again, a 10% difference in the derating factor cha... [more]

Wave energy converters (WECs) can play a significant role in the transition towards a more renewable-based energy mix as stable and unlimited energy resources. Financial analysis of these projects requires WECs cost and WEC capital expenditure (CapEx) information. However, (i) cost information is often limited due to confidentiality and (ii) the wave energy field lacks flexible methods for cost breakdown and parameterisation, whereas they are needed for rapid and optimised WEC configuration and worldwide site pairing. This study takes advantage of the information provided by Wavepiston to compare different costing methods. The work assesses the Froude-Law-similarities-based “Similitude method” for cost-scaling and introduces the more flexible and generic “CapEx method” divided into three steps: (1) distinguishing WEC’s elements from the wave energy farm (WEF)’s; (2) defining the parameters characterising the WECs, WEFs, and site locations; and (3) estimating elements that affect WEC an... [more]

Swine manure mono-digestion results in relatively low methane productivity due to the low degradation rate of its solid fraction (manure fibers), and due to the high ammonia and water content. The aqueous ammonia soaking (AAS) pretreatment of manure fibers has been proposed for overcoming these limitations. In this study, continuous anaerobic digestion (AD) of manure mixed with optimally AAS-treated manure fibers was compared to the AD of manure mixed with untreated manure fibers. Due to lab-scale pumping restrictions, the ratio of AAS-optimally treated manure fibers to manure was only 1/3 on a total solids (TS) basis. However, the biogas productivity and methane yield were improved by 17% and 38%, respectively, also confirming the predictions from a simplified 1st order hydrolysis model based on batch experiments. Furthermore, an improved reduction efficiency of major organic components was observed for the digester processing AAS-treated manure fibers compared to the non-treated one... [more]

In this study, a low-temperature drying plant based on renewable energies to dry food processing wastes is investigated. The demand-oriented heat supply is realized by a solar wall in combination with a biomass boiler. Due to the operational complexity of such a system with different sub-units and process parameters, steady-state simulations were performed in Aspen Plus to provide an insight into the process. Moreover, a time-resolved energetic evaluation was conducted to analyze the influence of varying capacity of the heat sources and operational strategy in addition to economic calculations. The simulations showed that an overall control strategy needs to consider the air properties as well as the flow rate of wet input material. In the reference case, the boiler must be operated at full load through the year to supply as much heat as possible. The revenue from the dried material was the most crucial parameter on the drying economics. Although the current plant configuration operati... [more]

Hybridizing a lead−acid battery energy storage system (ESS) with supercapacitors is a promising solution to cope with the increased battery degradation in standalone microgrids that suffer from irregular electricity profiles. There are many studies in the literature on such hybrid energy storage systems (HESS), usually examining the various hybridization aspects separately. This paper provides a holistic look at the design of an HESS. A new control scheme is proposed that applies power filtering to smooth out the battery profile, while strictly adhering to the supercapacitors’ voltage limits. A new lead−acid battery model is introduced, which accounts for the combined effects of a microcycle’s depth of discharge (DoD) and battery temperature, usually considered separately in the literature. Furthermore, a sensitivity analysis on the thermal parameters and an economic analysis were performed using a 90-day electricity profile from an actual DC microgrid in India to infer the hybridizati... [more]

Stand-alone microgrids integrating renewable energy sources have emerged as an efficient energy solution for electrifying isolated sites, such as islands and remote areas. The design of a microgrid involves various influential factors, including technological development, economic feasibility, and environmental impacts, based on the conditions and regulations of a particular site. This paper proposes a comprehensive microgrid design framework based on power system analysis and techno-economic analysis. The obtained optimal microgrid configuration satisfies both the design objective and power system performance regulations. The proposed design approach focuses on using practical data and can adapt to any microgrid design problems based on the local characteristics of a specific site. The practicality and effectiveness of the design framework are validated by applying it to the design of a stand-alone microgrid for Deokjeok Island in South Korea. The case study results justify the import... [more]

The resource endowment structure of being coal-rich and oil-poor makes China’s production of coal-based ammonia and urea, with a low production cost and a good market, a competitive advantage. However, the process suffers from high CO2 emissions and low energy efficiency and carbon utilization efficiency due to the mismatch of hydrogen-to-carbon ratio between raw coal and chemicals. Based on the coal-to-urea (CTU) process and coal-based chemical looping technology for urea production processes (CTUCLAS&H), a novel urea synthesis process from a coal and coke-oven gas-based co-feed chemical looping system (COG-CTUCLAS&H) is proposed in this paper. By integrating chemical looping air separation and chemical looping hydrogen production technologies and the synergies between coal gasification, low-energy consumption CO2 capture and CO2 utilization are realized; the excess carbon emissions of the CTU process are avoided through coupling the pressure swing adsorption of COG, and the low carbo... [more]

Life-cycle assessment (LCA) and techno-economic analysis (TEA) were applied to assess the economic feasibility and environmental benefits of utilizing multiple biomass feedstocks for bioenergy products under three different technological pathways with consideration of uncertainties. Three cases were studied for the production of pellets, biomass-based electricity, and pyrolysis bio-oil. A Monte Carlo simulation was used to examine the uncertainties of fossil energy consumption, bioenergy conversion efficiency, stochastic production rate, etc. The cradle-to-gate LCA results showed that pellet production had the lowest greenhouse gas (GHG) emissions, water and fossil fuels consumption (8.29 kg CO2 eq (equivalent), 0.46 kg, and 105.42 MJ, respectively). The conversion process presented a greater environmental impact for all three bioenergy products. When producing 46,929 Mg of pellets, 223,380 MWh of electricity, and 78,000 barrels of pyrolysis oil, the net present values (NPV) indicated... [more]

Large-scale deployment of both biochemical and thermochemical routes for advanced biofuels production is seen as a key climate change mitigation option. This study addresses techno-economic and environmental aspects of advanced liquid biofuels production alternatives via biomass gasification and Fischer−Tropsch synthesis integrated to a typical sugarcane distillery. The thermochemical route comprises the conversion of the residual lignocellulosic fraction of conventional sugarcane (bagasse and straw), together with eucalyptus and energy-cane as emerging lignocellulosic biomass options. This work promotes an integrated framework to simulate the mass and energy balances of process alternatives and incorporates techno-economic analyses and sustainability assessment methods based on a life-cycle perspective. Results show that integrated biorefineries provide greenhouse gas emission reduction between 85−95% compared to the fossil equivalent, higher than that expected from a typical sugarcan... [more]

This paper presents a techno-economic assessment of hydrokinetic energy of Cozumel Island, where ocean currents have been detected, but tourist activities are paramount. The main objective of this research is to identify devices that have been used to harvest hydrokinetic power elsewhere and perform an economic analysis as to their implementation in the Mexican Caribbean. First, the energy potential of the area was evaluated using simulated data available through the HYCOM consortium. Then, for four pre-commercial and commercial turbines, technical and economic analyses of their deployments were performed. Socio-environmental constraints were reviewed and discussed. Three optimal sites were identified, with an average annual hydrokinetic energy density of 3−6 MWh/m2-year. These sites meet the socio-environmental requirements for marine kinetic energy harvesting. Of the turbines considered in the analysis, the best energy price/cost ratio is that of SeaGen device, with a maximum theoret... [more]

A readily available source for renewable fuels and chemicals is corn stover, which consists of the leftover stalks, leaves, husks, and cobs from the corn plant and makes up nearly half of the yield of a corn crop. Common practice is to pretreat it with sulfuric acid to break down the hemicellulose, releasing xylose, followed by enzymatic hydrolysis to convert the cellulose into glucose. Using a Sn-Beta catalyst, it is possible to convert these monomeric sugars into lactic, levulinic, formic, and acetic acids. This paper presents the results of a techno-economic analysis (TEA) of the commercial feasibility of producing these acids from corn stover. Two preliminary process designs were evaluated which represent two separate reaction yields: a balanced yield of both lactic and levulinic acids and the yields from a co-catalysis with CaSO4 to produce primarily lactic acid. Both process designs are scaled to process 230,000 MT/year of corn stover. An AACS Class 4 factored broad capital cost... [more]

Hydrogen and biocarbon are important materials for the future fossil-free metallurgical industries in Sweden; thus, it is interesting to investigate the process that can simultaneously produce both. Process simulations of biomass pyrolysis coupled with steam reforming and water-gas-shift to produce H2, biocarbon, and bio-oil are investigated in this work. The process simulation is performed based on a biomass pyrolysis plant currently operating in Sweden. Two co-production schemes are proposed: (1) production of biocarbon and H2, and (2) production of biocarbon, H2, and bio-oil. Sensitivity analysis is also performed to investigate the performance of the production schemes under different operating parameters. The results indicated that there are no notable differences in terms of the thermal efficiency for both cases. Varying the bio-oil condenser temperature only slightly changes the system’s thermal efficiency by less than 2%. On the other hand, an increase in biomass moisture conte... [more]

In the grid-tied micro-grid context, energy resilience can be defined as the time period that a local energy system can supply the critical loads during an unplanned upstream grid outage. While the role of renewable-based micro-grids in enhancing communities’ energy resilience is well-appreciated, the academic literature on the techno-economic optimisation of community-scale micro-grids lacks a quantitative decision support analysis concerning the inclusion of a minimum resilience constraint in the optimisation process. Utilising a specifically-developed, time-based resilience capacity characterisation method to quantify the sustainability of micro-grids in the face of different levels of extended grid power outages, this paper facilitates stakeholder decision-making on the trade-off between the whole-life cost of a community micro-grid system and its degree of resilience. Furthermore, this paper focuses on energy infrastructure expansion planning, aiming to analyse the importance of m... [more]

Hybrid energy systems (HESs) generate electricity from multiple energy sources that complement each other. Recently, due to the reduction in costs of photovoltaic (PV) modules and wind turbines, these types of systems have become economically competitive. In this study, a mathematical programming model is applied to evaluate the techno-economic feasibility of autonomous units located in two isolated areas of Ecuador: first, the province of Galapagos (subtropical island) and second, the province of Morona Santiago (Amazonian tropical forest). The two case studies suggest that HESs are potential solutions to reduce the dependence of rural villages on fossil fuels and viable mechanisms to bring electrical power to isolated communities in Ecuador. Our results reveal that not only from the economic but also from the environmental point of view, for the case of the Galapagos province, a hybrid energy system with a PV−wind−battery configuration and a levelized cost of energy (LCOE) equal to 0... [more]

District heating-connected waste incineration plants face a serious operating challenge during the warmer months of the year when the heating load is quite low. The challenge is the difficulty of managing the extra municipal solid waste to be disposed of, exposing great pressure and cost on the plant. Conventionally, the solution is either burning the surplus waste and providing the extra cooling required for the condenser with a summer chiller and paying the tax of the total heat generation of the plant, or paying other industries to burn the waste for their specific applications. Both of these solutions are, however, costly. In this study, to address this challenge the utilization of the extra available resources of waste incineration plants for district cooling supply is proposed. Then, the proposed solution is analyzed from the thermodynamic and economic points of view. The feasibility of the proposal is investigated for a real waste incineration plant in Denmark and its 50 neighbo... [more]

The focus of this study is to provide a comparative techno-economic analysis concerning the deployment of small-scale gasification systems in dealing with various fuels from two countries, Portugal and Brazil, for electricity generation in a 15 kWe downdraft gasifier. To quantify this, a mathematical model was implemented and validated against experimental runs gathered from the downdraft reactor. Further, a spreadsheet economic model was developed combining the net present value (NPV), internal rate of return (IRR) and the payback period (PBP) over the project’s lifetime set to 25 years. Cost factors included expenses related to electricity generation, initial investment, operation and maintenance and fuel costs. Revenues were estimated from the electricity sales to the grid. A Monte Carlo sensitivity analysis was used to measure the performance of the economic model and determine the investment risk. The analysis showed an electricity production between 11.6 to 15 kW, with a general... [more]

The increase of capital investments and operation and maintenance (O&M) costs represents a current limitation to the diffusion of carbon capture systems for the clean combustion of fossil fuels. However, post-combustion systems, such as calcium looping (CaL), for CO2 capture from flue gas are the most attractive carbon capture systems since they can be installed at new plants and retrofitted into existing power plants. This work investigates the pros and cons of employing a calcium looping system for CO2 capture and also as a desulphurization unit. A preliminary techno-economic analysis was carried out comparing a base case consisting of a coal-based power plant of about 550MWe with a desulphurization unit (Case 1), the same plant but with a CaL system added for CO2 capture (Case 2), or the same plant but with a CaL system for simultaneous capture of CO2 and SO2 and the removal of the desulphurization unit (Case 3). Case 2 resulted in a 67% increase of capital investment with respect t... [more]

The use of energy storage with high power density and fast response time at container terminals (CTs) with a power demand of tens of megawatts is one of the most critical factors for peak reduction and economic benefits. Peak shaving can balance the load demand and facilitate the participation of small power units in generation based on renewable energies. Therefore, in this paper, the economic efficiency of peak demand reduction in ship to shore (STS) cranes based on the ultracapacitor (UC) energy storage sizing has been investigated. The results show the UC energy storage significantly reduce the peak demand, increasing the load factor, load leveling, and most importantly, an outstanding reduction in power and energy cost. In fact, the suggested approach is the start point to improve reliability and reduce peak demand energy consumption.

Among the driving factors for the high production cost of cellulosic butanol lies the pretreatment and product separation sections, which often demand high amounts of energy, chemicals, and water. In this study, techno-economic analysis of several pretreatments and product separation technologies were conducted and compared. Among the pretreatment technologies evaluated, low-moisture anhydrous ammonia (LMAA) pretreatment has shown notable potential with a pretreatment cost of $0.16/L butanol. Other pretreatment technologies evaluated were autohydrolysis, soaking in aqueous ammonia (SAA), and soaking in sodium hydroxide solution (NaOH) with pretreatment costs of $1.98/L, $3.77/L, and $0.61/L, respectively. Evaluation of different product separation technologies for acetone-butanol-ethanol (ABE) fermentation process have shown that in situ stripping has the lowest separation cost, which was $0.21/L. Other product separation technologies tested were dual extraction, adsorption, and membra... [more]

District cooling and heating methods that can utilize highly efficient heat pumps and various unused new and renewable types of energy are required to achieve low carbon emissions and zero energy usage in buildings and community units. The technical requirements for the implementation of decentralized thermal networks and heat trading are increasing, both for thermal networks in new buildings and for those remodeled based on existing centralized thermal networks. In this study, a conventional centralized thermal network was implemented as a decentralized thermal network and the possibility of heat prosumers feeding thermal networks was demonstrated experimentally. A real-scale plant was constructed by employing unused thermal energy facilities as prosumers in a school and childcare center based on the existing small-scale block heating and cooling thermal network. The decentralized thermal network and heat prosumer concepts were proven through operation experiments performed on the con... [more]

The aims of this paper are to develop hybrid energy systems considering biomass energy sources as well as a framework and optimal configuration of hybrid systems of energy for a southern sub-urban area of Bhola district in Bangladesh, named Kukri Mukri island, and analyse the feasibility of the techno-economic prospects of these systems. In this work, electrification for the rural area is analysed for different configurations of the hybrid systems. The estimation of available resources with optimal sizing and analysis of techno-economic aspects is done through HOMER Pro software to satisfy the demand of peak load. Different configurations of hybrid energy systems, including PV/diesel, PV/wind, PV/diesel/wind, PV/wind/diesel/biomass, and wind/diesel, are analysed and compared through optimization of different energy sources in HOMER. The size of the system and components are optimized and designed depending on the net present cost (NPC) and the levelized cost of energy (LCOE). Due to th... [more]